An antenna in the shape of a cylindrical rod projects from the top of a locomotive. If the antenna is 42 in long and 0.200 in. in diameter, compute the drag force on it when the locomotive is traveling at 160 mph in still air at -20°F.

An antenna in the shape of a cylindrical rod projects from the top of a locomotive. If the antenna is 42 in long and 0.200 in. in diameter, compute the drag force on it when the locomotive is traveling at 160 mph in still air at -20°F.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.55P

See similar textbooks

Related questions

Q: For the single degree of freedom system shown below in Figure Q6, and considering only the steady…

A: In order to solve this problem, we must first determine the natural frequency of the vibration and…

Q: A 25 hp suction pump operating at 70.00% efficiency draws water from a suction line whose diameter…

Q: (a) Determine the maximum tensile and compressive flexural stresses if the bending moment in the…

A: Given the bending moment and stress. Required: Corresponding maximum tensile and compressive stress…

Q: Determine the moments of inertia of the shaded area about the x- and y-axes. Answers: 04 94

Q: In the FAPT programming language, the following format of statement Si= is used to define:…

A: Format of statement is a standard way of giving a command in FAPT language to perform any specific…

Q: A stream of air at 110°F and 10 per cent relative humidity merges with a stream at 70° and 90 per…

Q: (b) Show that the lightest cantilever beam of length (b) L and square section (area free) that will…

Q: A body of has a dimension 1.5m × 1m × 2m having weight inside water is 1962 N. Find its weight

A: Given:Body dimesion=1.5 m×1.0 m×2 mweight of body inside water=1962 NFind,weight in air, W=?

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: Problem 2.2 Draw the free body diagram for the following beam with the distributed load replaced…

A: Given the loading conditions. Required: Free body diagram and reaction forces

Q: Learning Goal: To understand how to use the relative position and velocity equations to find the…

Q: In a C.I. engine working on the dual combustion cycle the compression ratio is 12.5:1. Air at…

Q: 9 Find the moment of inertia of the rod and solid sphere combination about the ans & shows in The…

Q: The spur gear arrangement shown has a pinion (driver Gear A) that rotates at 625 rpm, an idler Gear…

Q: 3-56. A 2-in. Younded orifice exists in the horizontal bottom of a large tank. The water in the tank…

A: According to the given data H=12ft h=6ft Cc=1 d=2in=0.16667 ft we need to find Discharge of the…

Q: The following table gives data, in kJ, for a system undergoing a power cycle consisting of four…

Q: 4. The 10-kg rod AB is pin-connected at A and subjected to a couple moment of M = 15 Nm. If the rod…

A: Given moment , mass and length of bar. Required: Angular velocity of rod.

Q: ermine the moment about the origin O of the force F = 4i + 10j + 6k that acts at a the position…

A: F=4i+10j+6k To find moment about O

Q: 3.21 Before the trunk of a large tree is felled, cables AB and BC are attached as shown. Knowing…

A: TBA =555N TBC=660 N To find moment of resultant force about point O

Q: efrigerant 22 at a pressure of 1500 kPa leaves the condenser

A: Given: The pressure of refrigerant leaving the condenser is, Pc=1500 kPa=1500×103 Pa. The vertically…

Q: Water jacketed compressor compresses 5 m³/min of air having an initial specific volume of 0.8m³/kg.…

A: Given data Volume flow rate = 5 m3/min Specific volume = 0.8m3/kg The increase in enthalpy =…

Q: Consider the steady-state model of the universe. In this model, the universe is made up of matter…

A: The rate of creation of matter per unit volume can be calculated using the equation: MV=ρ(1+3Ht)…

Q: For the system given in Q4 and shown again in Figure Q5, if k = 2.6 N/m, and m = 4.8 kg, find the…

A: According to the question m=4.8kg k=2.6 N/m We need to find Natural frequency

Q: A quarter car model of an automotive vehicle suspension system is shown in Figure Q2 below, where k,…

A: m1=257.5kg m2=28.8kg k1=24.4kN/m k2=83.2kN/m we need to find The first system natural frequency i.e…

Q: A tension test was performed on a specimen having an original diameter of 11.5 mm and a gauge length…

A: To plot: (a) The stress strain diagram and approximate the modulus of elasticity. (b) The ultimate…

Q: Problem 1. The following equation is given. W(P) = K (K₁ +7+) Find the differential equation and…

A: Given: The equation is: →W(p)=KK1+1Tip+TdpTf Because this is function of p so the by differentiating…

Q: A flow develops between two parallel plates, each of area (A). The plates are separated by a gap (H)…

A: The velocity expression in the x- direction is u(y)=12μ∆PLHy-y2+sgnUtyH The area of the plate is A.…

Q: Q3) A rectangular rosette is mounted on a steel plate having E = 29 × 10° psi and µ = 0.3. The th…

A: GivenE=29×106 psiμ=0.3ε1=+500 μ in/inε2=+400 μ in /inε3=-100 μ in/in

Q: 10) If the dynamic vircocity of water in ft2/sec? at 20°C is 0.0010 Pa-sec: What is its kinematic…

Q: What type of preloading system of ball screws is shown on the figure below? Tension Nut B Nut B…

Q: Find the natural frequency of the system shown in Fig. 2.55 with and without the springs k₁ and k₂…

A: Solution: Given Data: To Find: (a) Find the natural frequency when both the springs are present.…

Q: The following reaction 2 NO(g) + O₂(g) → 2 NO₂(g) was found to be first order in each of the two…

A: To choose: The correct option. Given: The reaction is 2NOg+O2g→2NO2g

Q: n has a heat loss of 6 W. The effectiveness of the fin is 3 and efficiency of the fin is 0.75 , what…

A: Given:actual heat transfer, Qa=6 Wefficiency of fin, η=0.75effectiveness of the fin, ε=3Find,The…

Q: For the single degree of freedom system shown below in Figure Q11, and considering only the steady…

A: Solution: Given Data: m=14.6 kgk=571.8 N/mc=7.5 N-s/mω=11.1 rad/s To Find: The phase difference…

Q: Calculate the following efficiencies for an assumed pumping system: a. Electric drive motor…

A: Using the conventional efficiency formula, we will compute the efficiency of the motor, the…

Q: 4-4. Determine the moment about point 4 of each of the three forces acting on the beam. F₂ = 500 lb…

A: Given that: F1 = 375 lb F2 = 500 lb F3 = 160 lb It is required to determine the moment of the three…

Q: determine the tension in all three cables if the bouyancy force on the balloon is 1035 N, the mass…

A: According to the given data F→=1035 j N W→=-87.7x9.81 j=-860.337 j Co-ordinates of the point…

Q: The beam of 15 m length and mass of 530 Kg is connected to the vertical wall by a hinge and is…

A: given L = 15m m = 530 kg so selfweight W = mg = 530*9.8 = 5194 N Let us consider tension in…

Q: An inclined, circular gate with water on one side is shown in the figure. Determine the total…

Q: Problem Statement Based on Problem 4-32 from the textbook. Determine the magnitude and coordinate…

A: Given data F = 45i+65j+30k Find the magnitude and direction angle of resultant moment about point A…

Q: Which of the five groups of the primary refrigerants has the adverse impact on the environment?…

A: Primary Refrigerants: The primary refrigerants are the fluids that are directly used as a working…

Q: 7. The relative humidity on a 90°F day is 30 per cent. a. How many pounds of water vapor are in a…

Q: Your manager asked you to explain the difference between three-point bending test and four-point…

A: The force is F=30 kN. The thickness is t=5 cm=0.05 m The width is b=10 cm=0.1 m. The length is L=25…

Q: Q4. A high-performance four-stroke SI engine has a swept volume of 875 cm and a compression ratio of…

A: (a) To find: The overall efficiency and SFC. Given: The swept volume is Vs=875 cm3=875×10-6 m3. The…

Q: Change multiview drawings to isometric

A: The required isometric views of the given orthographic views are drawn below.

Q: PROBLEM 1 Find the support reactions and joint force of the construction, shown on the figure, if:…

A: Write the given data. q=9 kN/mP=20 kNM=25 kNmL=1m

Q: antilever beam has flexural rigidity is EI=200 × 106 N.m2 is loaded with a concentrated force at its…

A: Given:EI=200 × 106 N.m2Area of bending moment diagram =10000 N.m2Find,Slope at free end?

Q: Q2. A 40 lbs lamp is suspended by cables as shown. What are the tensions in each of the 4 cables if…

A: To find: The tension in each of the cables. Given: The weight of the lamps suspended by cable is…

Q: A rigid tank contains saturated liquid - vapor water at 85°C. For this state, the specific volume,…

A: To find: The mixture's quality. Given: The mixture's temperature is T=85°C. The specific volume of…

Q: In the figure shown below, the deflection of mercury is initially 250mm . If the pressure at A is…

A: Given: Initial deflection of mercury =250 mm=0.25 m The pressure at A is increased by PA'=33 kPa

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Fick’s Law of Diffusion and Mass Transfer

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Answer correctly. Here is the Translation. "A luxury sports car has an area of 2 m² and there is a drag coefficient of 0.29 at a speed of 90 km/h. Calculate the drag force exerted on the car at this speed"
The wing loading on an airplane is defined as the aircraft weight divided by the wing area. An airplane is cruising with a wing loading of 2500 Pa. The lift coefficient and drag coefficient are 0.30 and 0.06, respectively. Calculate the drag force if the wing planform area is 12 m2. Assume that the air density is unknown and not given.
A truck having projected area of 6.5 m² and travelling at 72 km/h has a total resistance of 1.6 kN. Out of this resistance, 30% is due to rolling, 20% due to surface friction and rest is due to drag. Calculate the coefficient of drag if specific weight of air is 12 N/m^3.
A given airfoil develops a lift of 120 lb/ft at a given velocity of 120 mph under standard sea level conditions. Calculate the lift coefficient when the chord length is 9 ft. Round off answer to the nearest hundredths.
A small, fast boat has a specific resistance ratio of 0.06 (see Table 17.2) and displaces 125 long tons. Compute the total ship resistance and the power required to overcome drag when it is moving at 50 ft/s in seawater at 77°F.
A flat plate has a surface roughness of 0.1 mm, a width of 3 m, and a length of 2 m. Air with a velocity of 3 m/s flows over the plate. a. Calculate the drag exerted on the plate if the flow at the leading edge of the plate is laminar. b. Calculate the drag exerted on the plate if the flow at the leading edge of the plate is immediately tripped to turbulence due to the presence of an exposed bolt
A bulk liquid transport truck incorporates a cylindrical tank 3m in diameter and 10m long. For the tank alone, calculate the pressure drag when the truck is traveling at 80km/h in air at 0°C
Name some applications in which a large drag is desired.
Fairings are attached to the front and back of a cylindrical body to make it look more streamlined. What is the effect of this modification on the (a) friction drag, (b) pressure drag, and (c) total drag? Assume the Reynolds number is high enough so that the flow is turbulent for both cases.
A rotary mixer is constructed from two circular disks as shown. The mixer is rotated at 60 rpm in a large vessel containing a brine solution (SG = 1.1, μbrine=1.07×10-3 Pa-s). Determine the appropriate coefficient of drag using Low Reynolds Drag Coefficient. Neglect the drag on the rods and the motion induced in the liquid. Estimate the minimum torque and power required to drive the mixer. only HANDWRITTEN answer needed ( NOT TYPED)
The airplane as described has a stalling speed at sea level of 100 mph at the maximum take-off weight of 15,900 lb. The ambient air density at standard sea level is 0.002377 slug/ft3. Calculate the value of the maximum lift coefficient for the airplane.
Kindly give me both right solutions with clear calculations The drag polar of a glider is given by CD=0.01+0.022CL2 . If it is launched from a height of 400m in still air. Please determine:(a) the maximum lift to drag ratio ??;(b) the greatest possible ground distance it can cover.