4. The 10-kg rod AB is pin-connected at A and subjected to a couple moment of M = 15 Nm. If the rod is released from rest when the spring is unstretched at 8 = 30°, determine the angular velocity of the rod at the instant 8 = 60°. Thanks to the roller support at C, the spring always remains horizontal when the rod rotates.

4. The 10-kg rod AB is pin-connected at A and subjected to a couple moment of M = 15 Nm. If the rod is released from rest when the spring is unstretched at 8 = 30°, determine the angular velocity of the rod at the instant 8 = 60°. Thanks to the roller support at C, the spring always remains horizontal when the rod rotates.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rod AB has a mass of 20 kg，the mass of the piston A and B are both 5kg. Piston B is attached to a spring of constant k = 1200 N/m. The spring is un-stretched when θ = 0. If the rod is released from rest whenθ = 45° Please find÷ (1) the moment inertia of the rod AB about its mass center G (2)The angular velocity of rod AB at θ = 0° (3）the velocity of piston A at θ = 0° (4) the velocity of Piston B at θ = 0° (hint: regard the piston A, B, rod as a system, during the motion, except the spring, the weight of rod AB, the weight of pistonB also does work). g = 9.8 m/s2
The 3.8 kg block is descending at a rate of 1.2 m/s when the hydraulic cylinder BC exerts a force F=500 N on the brake arm. Determine the number of radians the wheel will rotate before the system comes to rest. The wheel has a mass of 25 kg and a radius of gyration about its center kO=300 mm. The coefficient of kinetic friction between the brake arm and the wheel is 0.25.
The 10-kg uniform slender rod is suspended at rest when the force of F = 150 N is applied to its end. Determine the angular velocity of the rod when it has rotated 180° clockwise from the position shown. The force is always perpendicular to the rod.
The 25-kg cylinder A is free to slide along rod BC. When the cylinder is at x=0, the 46-kg circular disk D is rotating with an angular velocity of 4.8 rad/s. (Figure 1) If the cylinder is given a slight push, determine the angular velocity of the disk when the cylinder strikes B at x=600mm. Neglect the mass of the brackets and the smooth rod.
In the figure, rod AB has a mass of 10 kg, and must slide within the slots as shown. If the spring is unstretched when θ = 0°, determine the angular velocity of the bar when it reaches that angle after being released from θ = 30°.
The body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slipping
The thin 12 kg bar has an angular velocity in a clockwise direction ω = 1.5 rad/s when in position shown. Determine its angular acceleration and the normal reactions of the smooth surface A and B at that time. i = (1/12) M . L² for a homogeneous thin bar of mass M and length L.
The 2.5-kgkg rod ACBACB supports the two 4.1-kgkg disks at its ends. If both disks are given a clockwise angular velocity (ωA)1=(ωB)1=4.6rad/s(ωA)1=(ωB)1=4.6rad/s while the rod is held stationary and then released, determine the angular velocity of the rod after both disks have stopped spinning relative to the rod due to frictional resistance at the pins AA and BB. Motion is in the horizontal plane. Neglect friction at pin CC.
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.
The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheels
While the system shown is in equilibrium, a counter-clockwise torque T =T0sin(ωt) N-m(with T0 = 226.6 and ω=7) is applied to teh disk. What is the disk angular speed ω0 = ? in rad/s at time t = 4.2 sec? ( I = 0.2 kg.m2, b = 7.8 N-m-s/r, k = 1,504 N/m, r = 0.52m )
The 30-kg turbine disk has a centroidal radius of gyration of 175 mm and is rotating clockwise at a constant rate of 60 rpm when a small blade of weight 0.5 N at point A becomes loose and is thrown off. Neglecting friction, determine the change in the angular velocity of the turbine disk after it has rotated through (a ) 90°, (b ) 270°.