An automobile engine develops 33.5 hp at 1,000 rpm. The clutch used to transmit this power in a single plate clutch with two pair of contact surfaces. The coefficient of friction is 0.4 and the mean diameter of the disk is to be 190 mm. The average normal stres on the clutch lining is 120 kPa. 3. Determine the axial force to engage the clutch based on uniform wear. A. 1.57 kN B. 3.14 kN С. 5.28 kN D. 7.46 kN

An automobile engine develops 33.5 hp at 1,000 rpm. The clutch used to transmit this power in a single plate clutch with two pair of contact surfaces. The coefficient of friction is 0.4 and the mean diameter of the disk is to be 190 mm. The average normal stres on the clutch lining is 120 kPa. 3. Determine the axial force to engage the clutch based on uniform wear. A. 1.57 kN B. 3.14 kN С. 5.28 kN D. 7.46 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum, minimum and average pressure in a plate clutch when the axial force is 3.3kN. The inside radius of the contact surface is 81mm and the outside radius is 110 mm. Assume uniform wear.
The inner and outer radii of a hollow steel shaft are 50 mm and 100 mm, respectively. The hub of a steel gear wheel that is shrunk onto the hollow shaft has an outer radius of 150 mm. The maximum allowable tangential stress developed by shrinking the gear wheel onto the hollow shaft is 200 MPa. The length of hub parallel to the shaft axis is 200 mm, and the coefficient of static friction between the hub and the shaft is 0.40. Determine the maximum torque that may be transmitted by the gear wheel without slipping on the shaft.
An engine developing 40 hp at 1250 rpm is fitted with a cone clutch built into the flywheel. The con a face angle of 12.5 degrees and a mean diameter of 14 in. The coefficient of friction ta 0.20 and the n pressure on the clutch face is not to exceed 12 psl. Determine the required face width and the force m sary to engage the clutch, assuming uniform wear. Ans. 2.96 in.. 592 lb
A pulley is keyed to a 2.5 in diameter by means of a 5/8’’ x 7/16’’ x 3’’ flat key. The allowable bearing stresses for the key, hub and shaft are 66 ksi, 59 ksi and 72 ksi, respectively. Determine the maximum power that the pulley can safely transmit at 300 rpm.
Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of friction between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm2.
A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone is 200 mm, the cone face is 50 mm and the cone face makes an angle of 12 degrees with the horizontal. Determine the axial force necessary to engage the clutch to transmit 7 kW if the coefficient of friction of the contact surfaces is 0.15. What is the maximum pressure on the contact surfaces assuming uniform wear?
An multi axial plate clutch used in injection molding machine consist of a three pairs of contact surfaces for engaging and disengaging power from the engine. The engine used for power has a maximum torque capacity of 120 N-m and is transmitted to machine without losses. The permissible intensity of pressure is 350 kPa and the coefficient of friction is 0.35 for the clutch system used in the machine. It was determined that the machine will operate on maximum capacity of torque if the ratio of inner diameter to outside diameter of the axial clutch is 0.577. Assuming uniform wear theory, calculate the inner and outer diameters of the friction lining.
A pulley is keyed to a 56.8mm diameter shaft by a 7/16 in x 3 in flat key. The shaft rotates at 697 rpm. The allowable compressive stress for the key, hub and shaft are 66 ksi. 59 ksi and 72 ksi, respectively. Determine the maximum torque, in lb-in, the pulley can safety deliver. Express your answer in 3 decimal places.
An automotive plate clutch consists of two pairs of contacting surfaces with asbestos friction lining. The maximum engine torque is 200 N-m. The coefficient of friction is 0.35. The inner and outer diameters of friction lining are 200 and 300 mm respectively. Clamping force is provided by nine springs, each compressed by 4 mm to give a force of 700 N, when the clutch is new.(i) What is the factor of safety with respect to slippage when the clutch is brand new?(ii) What is the factor of safety with respect to slippage after initial wear has occurred?(iii) How much wear of friction lining can take place before the clutch will slip?
for q1) B at the point : frictional force at A is...the frictional force in the vertical direction wasnt included. is this correct? should it not be Rb+Tsin30-W+Fa?
A mild steel cover plate is to be designed for an inspection hole in the shell of a pressure vessel. The hole is 120 mm in diameter and the pressure inside the vessel is 6 N/mm2. Design the cover plate along with the bolts. Assume allowable tensile stress for mild steel as 60 MPa and for bolt material as 40 MPa
(6) A double square-threaded power screw transmits 1,800in-lb of torque and raises a machine head; the head is guided by linear slides with anti-friction bearings, and thus no appreciable friction is involved. If the coefficient of friction for the threads is 0.1, find: (a) the load that can be raised if the screw has 2 threads/in and an outside diameter of 2½in; (b) if a 4000-lb load is to be lowered, what torque must the screw transmit? (c) if the power screw of rotates 10 rpm, what is the linear speed of the driven head in feet per minute?