An automobile tire is shown in the figure below. The tire is made of rubber with a uniform density of 1.10 x 103 kg/m3. The tire can be modeled as consisting of two flat sidewalls and a tread region. Each of the sidewalls has an inner radius of 16.5 cm and an outer radius of 30.5 cm as shown, and a uniform thickness of 0.660 cm. The tread region can be approximated as having a uniform thickness of 2.50 cm (that is, its inner radius is 30.5 cm and outer radius is 33.0 cm as shown) and a width of 17.8 cm. What is the moment of inertia (in kg m2) of the tire about an axis perpendicular to the page through its center? Sidewall 33.0 cm 16.5 cm 30.5 cm Tread

An automobile tire is shown in the figure below. The tire is made of rubber with a uniform density of 1.10 x 103 kg/m3. The tire can be modeled as consisting of two flat sidewalls and a tread region. Each of the sidewalls has an inner radius of 16.5 cm and an outer radius of 30.5 cm as shown, and a uniform thickness of 0.660 cm. The tread region can be approximated as having a uniform thickness of 2.50 cm (that is, its inner radius is 30.5 cm and outer radius is 33.0 cm as shown) and a width of 17.8 cm. What is the moment of inertia (in kg m2) of the tire about an axis perpendicular to the page through its center? Sidewall 33.0 cm 16.5 cm 30.5 cm Tread

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter1: Physics And Measurement

Section: Chapter Questions

Problem 1.67AP: A rod extending between x = 0 and x = 14.0 cm has uniform cross-sectional area A = 9.00 cm2. Its...

See similar textbooks

Similar questions

How would you determine the density of an irregularly shaped rock?
Check Your understanding Repeat ExampIe12.4 assuming that the forearm is object of uniform density that weighs 8.896 N.
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
A straightforward method of finding the density of an object is to measure its mass and then measure its volume by submerging it in a graduated cylinder. What is the density of a 240-g rock 89.0 cm3 of water? (Note that the accuracy and practical applications of this technique are more limited than a variety of others that are based on Archimedes' principle.)
A container of water has a cross-sectional area of A=0.1m2 . A piston sits top of the water (see be following figure). There is a spout located 0.15 m from the bottom of tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spat is As=7.0104m2 . (a) What is the velocity of the water as it leaves the spout? (b) If the opening of the spout is located 1.5 m above the grand, how far from be pout does water hit the floor? Ignore friction and dissipative forces.
Suppose you have a coffee with a circular cross-section and vertical sides (uniform radius). What is its inside radius if it holds 375 g of coffee filled to a depth of 7.50 cm? Assume coffee has the same density as water.
A rod extending between x = 0 and x = 14.0 cm has uniform cross-sectional area A = 9.00 cm2. Its density increases steadily between its ends from 2.70 g/cm3 to 19.3 g/cm3. (a) Identify the constants B and C required in the expression = B + Cx to describe the variable density. (b) The mass of the rod is given by m=allmaterialdV=allxAdx=014.0cm(B+Cx)(9.00cm2)dx Carry out the integration to find the mass of the rod.
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
Show that the Reynolds number NRis unitless by substituting units for all the quantities in its definition and cancelling.
A certain hydraulic system is designed to exert a force 100 times as large as the put into it. (a) What must be the ratio of the area of the cylinder that is being controlled to area of the master cylinder? (b) What must be the ratio of their diameters? (c) By what factor is the distance through which the output force moves reduced relative to the distance through which input force moves? Assume no losses due to friction.
Check Your Understanding Explain why the concepts of Young’s modulus and shear modulus do not apply to fluids.
Logs sometimes float vertically a lake because one end has become water-logged and denser than the other. What is the average density of a uniform-diameter log that floats with 20.0% of its length above water?