An axial load P is supported by the short steel column shown in the figure. The column has a cross-sectional area of 0.0105 m. If the average normal stress in the steel column must not exceed 125 MPa, determine the minimum required dimension a so that the bearing stress between the base plate and the concrete slab does not exceed 8 MPa. Assume b = 750 mm P 9.

An axial load P is supported by the short steel column shown in the figure. The column has a cross-sectional area of 0.0105 m. If the average normal stress in the steel column must not exceed 125 MPa, determine the minimum required dimension a so that the bearing stress between the base plate and the concrete slab does not exceed 8 MPa. Assume b = 750 mm P 9.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Similar questions

A steel column of hollow circular cross section shown in Figure 2 is supported on a circular steel base plate and a concrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680 kN. a. Determine the bearing stress induced by the column to the base plate in MPa. b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.
A steel column of hollow circular cross section shown in Figure 2 is supported on a circular steel base plate and aconcrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680kN.a. Determine the bearing stress induced by the column to the base plate in MPa.b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
An axial load P is supported by the short steel column shown in the figure. The column has a cross-sectional area of 14,400 mm2. If the average normal stress in the steel column must not exceed 69 MPa, determine the minimum required dimension a (in mm rounded to the nearest tenths) so that the bearing stress between the base plate and the concrete slab does not exceed 8 MPa. Assume b = 400 mm.
An axial load P is supported by a short steel column, which has a cross-sectional area of 10500 mm2. If the average normal stress in the steel column must not exceed 140 MPa, determine the minimum required dimension “a” so that the bearing stress between the base plate and the concrete slab does not exceed 11 MPa.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The f'c is 28 and the fy is 420. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam
A simply supported wood beam with overhang is subjected to uniformly distributed load q. * Inserted Photo * The beam has a rectangular cross section with width b = 200 mm and height h = 250 mm.Determine the maximum permissible value q if the allowable bending stress is ?all = 11.2 MPa, and the allowable shear stress is ?all = 1.50 MPa. (Enter the magnitude in kN/m.)
A trailer truck crossing a 10-m span circular beam ( D = 400 mm ) has axle loads of 7 kN, 9 kN, and 16 kN separated respectively by distances of 2 m and 5 m. Calculate the maximum bending stress and transverse stress developed in the beam.( detailed solution with FBD please, thank you) τmax = ? MPa σfmax = ? MPa
Two steel [E = 29,800 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.750 in. and a wall thickness of 0.278 in. Pipe (2) has an outside diameter of 3.750 in. and a wall thickness of 0.209 in. Assume L= 10 ft and L›= 15 ft. If the normal stress in each steel pipe must be limited to 15 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).
A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and carries a concentrated load of 25 KN at the midspan. What is the maximum flexural stress of the beam? Blank 1 (use two decimal places)
The simple beam carries a concentrated load P = 15kN. Dimension a and b are 2.5m and 1.2m. respectively. What is the required section modulus of the beam, in mm^3, if the stress is 120Mpa?