Question 5 The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the magnitude of the force P that would result in a 0.18-in. horizontal displacement of bar AB. Use G = 70 x 10° psi for the plastic, and neglect the deformation of the steel frame. A 3 ft B 2 ft Plastic sheet 2.

Question 5 The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the magnitude of the force P that would result in a 0.18-in. horizontal displacement of bar AB. Use G = 70 x 10° psi for the plastic, and neglect the deformation of the steel frame. A 3 ft B 2 ft Plastic sheet 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

USING CONJUGATE BEAM METHOD Consider 150 mm x 200 mm (bxh) mm section and e = 80 GPa DETERMINE REACTION AT D Values: A = 9.4 M B = 5.5 kN/m C = 20 kN
Determine the force P required to force the 11° wedge under the 93-kg uniform crate which rests against the small stop at A. The coefficient of friction for all surfaces is 0.46.
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
Determine the vertical displacement of joint A if members AB and BC experience a temperature increase of ΔT = 200°F. Take A = 2 in2 and E = 29(103) ksi. Also, α = 6.60 (10-6) /°F.
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.
The standard length of a tape is 100m having a weight of 1.2kg with the standardtemperature of 20 C and standard pull of 5.5kg. The young modulus of elasticity of thetape is 200GPa, cross sectional area is 2.8mm? and the coefficient of linear expansionis 0.0000116/°C. Determine the normal tension of the tape.
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Draw a free body diagram of rigid bar ABD, and determine the magnitude of the vertical reaction force at pin D.Answer:D = kN
Compute the value of EIy at 2.5 m from the left support.
H.W The uniform thin pole has a weight of 50 N and a length of 26m. If it is placed against the rough wall and on the rough box in the position d= 10 m, us =0.3 at points A, B and C P= 150 N Box weight= 100N Determine the distanice x when the motion of the pole impend
Determine the smallest force P needed to lift the 3000-lb load. The coefficient of static friction between A and C and between B and D is μs = 0.3, and between A and B μ's = 0.4. Neglect the weight of each wedge.