An eight-pole 60-Hz ac induction motor produces an output power of 2 hp and has rotational losses of 100 W at a speed of 850 rpm. Determine the slip, the frequency of the stator currents, the frequency of the rotor currents, and the rotor copper loss.

An eight-pole 60-Hz ac induction motor produces an output power of 2 hp and has rotational losses of 100 W at a speed of 850 rpm. Determine the slip, the frequency of the stator currents, the frequency of the rotor currents, and the rotor copper loss.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 13RQ: A squirrel-cage induction motor is operating at 1175 RPM and producing a torque of 22 Ib-ft. What is...

See similar textbooks

Related questions

Q: For a 4 pole induction motor find the synchronous speed if its running at 440V, 50 Hz A.C. supply.

A: Given Pole, p = 4 Frequency, F =50Hz

Q: A 220-V dc shunt motor runs at 500 rpm, when the armature current is 50 A. Calculate the speed if…

A: Given, Problem regarding to shunt motor. Please find the below attachments for the clear…

Q: A 1200 rpm, 700V Series DC motor has an armature resistance of 20 and the field resistance of 90. If…

A: efficiency = output powerinput power = input power - lossesinput power input power to motor =…

Q: The torque–speed curve of a particular 10-pole induction motor is approximately linear for low…

Q: A synchronous motor is running at 75 percent of rated load with unity power factor. If the load…

Q: A permanent-magnet dc motor has RA=0.5 Ω. With no load, it operates at 1070 rpm and draws 0.5 A from…

Q: A 6 pole, 50 Hz, 3 phase induction motor running on full load develops a useful torque of 150 N.m at…

A: The solution can be achieved as follows.

Q: A three-phase, 50-Hz, 6-pole induction motor develops a useful torque of 120 Nm at full-load, while…

A: Given : Pole = 6 Frequency =50 HZ Useful Torque = 120 Nm Rotor Frequency = 2 HZ torque Lost = 10…

Q: A three-phase, 50 Hz, 160 kW, 400 V (line-line rms) delta connected squirrel cage induction machine…

A: Given, A 3-phase delta connected squirrel cage induction machine, Rated frequency, f=50 Hz Rated…

Q: We want a four-pole synchronous motor that operates at a speed of 1000 rpm. Determine the frequency…

A: The operating speed of synchronous machine is defined as follows: Here P = number of magnetic…

Q: A 220-V-rms (line-to-line), 60-Hz, three-phase induction motor operates at 3500 rpm while delivering…

A: From problem description we have: Vin = 220 V rms Iin = 8 A rms Nfull load = 3500 rpm f = 60Hz Pout…

Q: A 440-V-rms (line-to-line voltage) three-phase induction motor runs at 1150 rpm driving a load…

A: The given values are ,VL = 440 vN = 1150 rpmT = 15 Nmpf = 0.8iL = 3.4 AThe expression of o/p…

Q: A two-pole 60-Hz induction motor produces an output power of 5 hp at a speed of 3500 rpm. With no…

A: given: P = 2 ; f= 60 Hz ; nm1 = 3500 rmp ; nno load = 3538 rmp ; Tloss = constant Pout = 5 hp…

Q: A synchronous motor is running at 100 percent of rated load with unity power factor. If the field…

A: Given: Pdev = Pload ; PF = 1 a) the output power is independent of field current. Hence if the…

Q: A 750 kW, 3300V, 50 Hz, wound-rotor three-phase induction motor with a star-connected stator winding…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: A separately excited dc motor has the following nameplate data: 100 hp, 440 V, 2000 rpm. (a)…

A: According to question: The rated torque is calculated as ∵T=60P2πN⇒T=60×100×7462π×2000⇒T=356.2N-m

Q: A 4-pole, 50-Hz induction motor has a full-load slip of 5%. Each rotor p resistance of 0.3 2 and…

A: In this question we will find ratio of maximum torque to full load torque and speed at which maximum…

Q: See attached.

Q: A four-pair of pole, 50-Hz squirrel-cage induction motor runs on load at a shaft speed of 720 rpm.…

Q: A 20 hp, 4 pole, 50 Hz, induction motor has a full-load slip of 4%, find its (A) Synchronous speed…

A: Given: Power=20 hpP=4f=50 Hzs=4 % (A) Calculate the Synchronous speed; Ns=120fPNs=120×504Ns=1500 rpm…

Q: (A)Give a clear explanation of the following effects in a three-phase induction motor: (1) the…

Q: A 60-Hz wound-rotor induction motor operates at 40 percent slip with added rotor resistance to…

Q: A 230-V, 60-Hz, 6-pole, Y-connected, three-phase induction motor has the following parameters in…

A: Note: As per our honor code, we are authorized to answer only 3 sub-parts, we’ll answer the first…

Q: A 6600-V, star-connected, 3-phase synchronous motor works at constant voltage and constant…

A: Given: A 6600-V, star-connected, 3-phase synchronous motor works at constant voltage and constant…

Q: induction

Q: Design a DC motor circuit to drive A fan-type load with a torque equation equal to:…

Q: A three-phase, 50-Hz, 6-pole induction motor develops a useful torque of 120 Nm at full-load, while…

A: Here 3 phase induction motor is given and the rotor frequency is given so find the slip synchronous…

Q: A 250 V dc shunt motor takes a current of 30A on a certain load. R= 12 and Rh= 125 Q. Find the…

A: Given: A DC shunt motor has, Load voltage, VL=250 V Load current, IL=30 A Armature resistance, Ra=1…

Q: 8. A 18600 W induction motor with six poles operates at 60HZ and shows a full-load slip of 6%: i)…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: Questióñ 1 A four pole, 50HP, 440V three phase induction motor with an operational frequency of…

A: airgap field speed of rotation is same as Speed of rotating magnetic field which is same as…

Q: A 10-hp six-pole 60-Hz three-phase induction motor runs at 1160 rpm under full-load conditions.…

A: In this question, We need to determine the the slip and the frequency of the rotor currents at full…

Q: A 1200 rpm, 700V Series DC motor has an armature resistance of 20 and the field resistance of 90. If…

A: Efficiency = output power/ input power. Total losses = cupper loss + rotational losses.

Q: Q5// A: The below curve represents Ta/la characteristic of a dc series motor. Briefly discuss this…

Q: A DC series motor of 240 V as input voltage has an armature resistance of 0.5 N and a field…

A: Given DC series motor of Input voltage V=240 vArmature resistance Ra=0.5 ΩField resistance Rf=10…

Q: A 3-phase, 4-pole, 230-V, wound rotor induction motor has both its stator and rotor connected in Y.…

A: Given data- No. of Phase ϕ=3 No. of Pole P=4 Voltage V=230 v…

Q: A 40Hp, 230V, 10pole, 50Hz three-phase induction motor is running at 585 rpm at rated load. If the…

Q: A three-phase, 230 V, 30 hp, 60 Hz, six-pole induction motor is operating with a shaft load that…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: a) What is the operating principle of induction motor?

A: As per the honour code I will only do part a question 1. Kindly repost the other questions again.…

Q: 7. A 3-phase, 4 pole, 230 V, 60 Hz wound-rotor induction motor has both its stator and rotor…

A: Induction motor: Induction motor is use in our daily life like kitchen, water pumps, automobiles,…

Q: a) A 2hp, 8-pole, 30 induction motor is connected to a 60 Hz power supply. From this motor, find; i)…

Q: Design a DC motor circuit to drive A fan-type load with a torque equation equal to:…

A: Given:

Q: A 15-hp, 230 V single-phase synchronous motor is taking a current of 50 A at a power factor of 0.85…

A: we need to determine rotational losses.

Q: 2. A 40-HP, 230-V., 8-pole, 25 Hz three-phase induction motor is running at 355 rpm at rated load.…

Q: a) In the experiment of performance study of three-phase wound rotor induction motor, what are the…

Q: A certain shunt-connected DC motor has RA =1 Q, a total field resistance Rp Q, and VT = 200 V. At a…

Q: The rotor of a 6-pole, 50-Hz induction motor is rotated by some means at 100 rpm. Compute: a. Rotor…

Q: 3. A4-pole, 50-Hz induction motor has a full-load slip of 5%. Each rotor phase has a resistance of…

Q: The full-load slip of a 54 Az, a four-pole induction motor is 4 %. The power converted from…

A: Given data, In induction motor f=54 HzP=4sfl=4%=0.04P0=23.1 kW

Q: A three-phase 60 Hz two-pole induction motor runs at a no-load speed of 3500 rpm and a full-load…

Concept explainers

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A squirrel-cage induction motor is operating at 1175 RPM and producing a torque of 22 Ib-ft. What is the horsepower output of the motor?
A 10-hp six-pole 60-Hz three-phase induction motor runs at 1160 rpm under full-load conditions. Determine the slip and the frequency of the rotor currents at full load. Also estimate the speed if the load torque drops in half.
A 10-hp six-pole 60-Hz three-phase induction motor runs at 1160 rpm under full-load conditions. Determine the slip and the frequency of the rotor currents at full load. Estimate the speed if the load torque drops in half.
An 8-pole, 3-phase, 50 Hz, induction motor is running at a speed of 710 rpm with an input power of 35 kW. The stator losses at this operating condition are known to be 1200 W while the rotational losses are 600 W. Find: the net torque and the mechanical power output
A two-pole 60-Hz induction motor produces an output power of 5 hp at a speed of 3500 rpm. With no load, the speed is 3598 rpm. Assume that the rotational torque loss is independent of speed. Find the rotational power loss at 3500 rpm.
A 10hp six-pole 60-Hz three-phase induction motor runs at 1090 rpm under full-load conditions. a)Determine the slip of the rotor currents at full load. b) Determine the frequency of the rotor currents at full load. c) Estimate the speed if the load torque drops in half.
A four-pole, three-phase induction motor drives aturbine load. At a certain operating point the machinehas 4 percent slip and 87 percent efficiency. The motordrives a turbine with torque–speed characteristic givenby TL = 20 + 0.006ω2. Determine the torque at themotor-turbine shaft and the total power delivered tothe turbine. What is the total power consumed by themotor?
Q#1: a) What is the operating principle of induction motor? b) Differentiate between induction motor and synchronous motor; give at least one practical example. c) What are the principle characteristics of DC series motor and DC compound motor, and what are its uses?
A three-phase, 50-Hz, 6-pole induction motor develops a useful torque of 120 Nm at full-load, while the rotorfrequency is 2 Hz. The torque lost due to friction and windage is 10 Nm. Calculate:1.output power 2. rotational losses
A 6-pole, 50 Hz, 3-phase induction motor runs at 960 rpm while delivering a shaft torque of 120 N-m. If friction and windage loss amount to 180 W., determine the rotor copper loss.
{Q.1} A three-phase induction motor runs at almost 1198 revolutions per minute (rpm) at no load and 1112 rpm at full load when supplied from a 60-Hz, three-phase source. (a) How many poles does this motor have? (b) What is the slip in percent at full load? (C) What is the corresponding frequency of the rotor currents? (D) What is the corresponding speed of the rotor field with respect to the rotor and with respect to the stator?
A 60-Hz wound-rotor induction motor operates at 40 percent slip with added rotor resistance to achieve speed control. The stator resistance is negligible compared with the rotor resistance. Neglect rotational losses. Find the efficiency of this motor.