An electric motor drives a compressor by use of V-belt. The pulley diameter of the compressor shaft is 1.2 meter while the pulley diameter of the motor shaft is 1 meter. The belt speed runs at 30 m/s. The center distance between pulleys is 1.75 m. The groove angle of the pulleys is 35%. Determine the power generated in kW if the tension at the tight side of the belt is 670.5 N. The coefficient c friction between the belt and the pulley is 0.27.

An electric motor drives a compressor by use of V-belt. The pulley diameter of the compressor shaft is 1.2 meter while the pulley diameter of the motor shaft is 1 meter. The belt speed runs at 30 m/s. The center distance between pulleys is 1.75 m. The groove angle of the pulleys is 35%. Determine the power generated in kW if the tension at the tight side of the belt is 670.5 N. The coefficient c friction between the belt and the pulley is 0.27.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A man produces a power output P as he lifts a weight of 200 newtons to height H in time T. If a second person is to lift the same weight to height of 2H in time T/2 he would produce a power output of *P/4P/22P4P
In a belt–pulley wheel system, the effective tension in the belt is 500 N and the diameter of the driver wheel is 200 mm. If the power output from the driving motor is 5 kW, the driver pulley wheel turns at: 50 rad/s 2500 rad/s 100 rad/s 0.1 rad/s
In an air compressor, the compression takes place at constant internal energy, and 50 kJ of heat is rejected to the cooling water for every one kilogram of air. Find the work required for the compression. 2- In a compression stroke of a gas engine, the work done on the gas by the piston is 70 kJ and the heat rejected to the cooling water is 42 kJ. Find the change of the internal energy. Stating whether it is gain or lost. 3- A mass of gas with an initial internal energy of 1500 kJ, is contained in a cylinder which has perfectly thermal insulated. The gas is allowed to expand behind a piston until its internal energy is 1400 kJ. Calculate the work done by the gas. If the expansion follows a lawPV2=C and the internal energy is changed. The initial pressure and volume are 28 bar and 0.06 m3 respectively. Calculate the final pressure and volume.
An automobile of weight 2500 kg moves downward on incline plane of angle (30°) with constant velocity (12.5) m/s. The resistance equal (2/100) from the weight of the automobile. Find the horsepower of the automobile.
A truck and trailer must be able to accelerate at 0.3 m/s2 up an incline of 1 in 20. The truck’s engine generates a torque of 900Nm. It has a moment of inertia of 30kg.m2 . The efficiency of the truck’s transmission is 83%. The mass of the truck is 12 tons, and that of the trailer is 9tons. The tractive resistance for both the truck and the trailer combined is 60N/ton. The truck has 12 wheels and the trailer has 8 wheels. The wheels on both vehicles are identical. Each wheel has a diameter of 1.2m, a mass of 75kg and a radius of gyration of 500mm. Determine two suitable overall gear ratios.
A stone crusher machine working 8 hours a day is driven by an electric motor with a narrow-V belt-pulley mechanism. The transmitted power is P = 18.5 kW, the speed of the motor is n1 = 1450 RPM, and the required rotational speed for the stone machine is n2 = 690D / d. Sizing of the narrow-V belt-pulley mechanism is required according to the given. Recommended value for the axle spacing a = k. (dw1 + dw2) k = 0.9
A belt drives a pulley of 200mm diameter such that the ratio of tensions in the tight side and slack side is 1.2. If the maximum tension in the belt is not to exceed 240KN. Find the safe power transmitted by the pulley at a speed of 60rpm.
A motor drives four loads, two have rotational motion and two have translational motion. The momentof inertia of the motor is 1.2kg-m^2. The motor runs at a speed of 1000rpm. The table below shows thedetails of the four loads. Calculate the power developed by the motor. (Load ;Type of Motion; Speed; Inertia / Mass; Torque / Force) 1; Rotational; 200 rpm; 7 kg-m^2; 10 N-m 2; Rotational; 200 rpm; 5 kg-m^2; 6 N-m 3; Translational; 10 m/s; 10 kg; 20 N4; Translational; 10 m/s; 20 kg; 30 N
An electric motor drives a gearbox of a conveyor belt via a fluid coupling. The motor delivers 40 kW at a speed of 1550 r/min. Take the efficiency of the coupling as 96% and calculate: a. the torque on the gearbox shaft, b. the speed of the gearbox shaft, c. the heat developed in the couplin
1) A 100-V shunt motor is developing 6 hp while operating at an overall efficiency of 86%. The armature and shunt field resistances are 0.06 and 50 ohms respectively. Determine the stray power losses. 2) The field and armature resistance of a 400 V shunt motor are 200 ohms and 0.1 ohms, respectively. The motor takes 30 A of current while running at 1000 rpm. If the frictional losses are 400 W, determine the motor efficiency. 3) In a brake test of an elevator door, the ammeter and voltmeter measuring the input read 34 A at 220 V. The speed of the motor is found to be 910 rpm and the balance on the 0.61 m brake arm reads 11.9 kg. The dead weight of the arm is found to be 1.09 kg. What is the hp output of the motor?
Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The diameter of the larger pulley is ‘3’ m and that of smaller pulley ‘3’ m. The initial tension in the belt when stationary is ‘4’ kN. The coefficient of friction between the belt and the pulley is 0.3. Calculate the power transmitted, when the smaller pulley rotates at ‘700’ r.p.m. and length of the belt.
the torque-velocity (T/(w)) relations of the two machines with their shafts clamped together at constant voltage; T1(w)=a1-b1w a1=150Nm b1=1Nm . s/rad T2(w)=a2-b2w a2=270Nm b2=2Nm . s/rad friction will be neglected and there is also no load. question= Find the idle speed of the motors alone (not clamped).?