An electrical circuit is shown in Figure B1 with the load resistor as 10K 2. 5KN зока 10 KN 25KN 12V Figure B1 By using Thevenin's Theorem calculate the following: i. Current flowing through the load resistor10K 2. ii. Power dissipated across the load resistor10K 2.

An electrical circuit is shown in Figure B1 with the load resistor as 10K 2. 5KN зока 10 KN 25KN 12V Figure B1 By using Thevenin's Theorem calculate the following: i. Current flowing through the load resistor10K 2. ii. Power dissipated across the load resistor10K 2.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 55P: A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any...

See similar textbooks

Similar questions

Consider the circuit below, (a) What is the initial current through resistor R2? when the switch is closed? (b) What is die current through resistor R2 when the capacitor is fully charged, long after die switch is closed? (c) What happens if the switch is opened after it has been closed for some rime? (d) If the switch has been closed for a time period long enough for the capacitor to become fully charged, and then the switch is opened, how long before the current through resistor R1 reaches half of its initial value?
A person with body resistance between his hands of 10.0k accidentally grasps the terminals of a20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation, (b) If the internal resistance of the power supply is 2000 , what is thecurrent through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low- resistance devices? Explain your reasoning.
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,
Integrated Concepts (a) An aluminum power transmission line has a resistance of 0.0580/km. What is its mass per kilometer? (b) What is the mass per kilometer of a copper line having the same resistance? A lower resistance would shorten the heating time. Discuss the practical limits to speeding the heating by lowering the resistance.
Integrated Concepts A flashing lamp in a Christmas earring is based on an RC discharge of a capacitor through its resistance. The effective duration of the flash is 0.250 s, during which it produces in average 0.500 W from an average 3.00 V. (a) What energy does it dissipate? (b) How much charge moves through the lamp? (c) Find the capacitance. (d) What is the resistance of the lamp?
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
A 20.00-ohm; 5.00-watt resistor is placed in series with a power supply, (a) What is the maxim tun voltage that can be applied to the resistor without hanniug the resistor? (b) What would be the current through the resistor?
Integrated Concepts (a) An immersion heater utilizing 120 V can raise the temperature of a 1.00 102 -g aluminum cup containing 350 g of water from 20.0°C to 95.0°C in 2.00 min. Find its resistance, assuming it is constant during the process. (b) A lower resistance would shorten the heating time. Discuss the practical limits to speeding the heating by lowering the resistance.
Ralph has three resistors, R1, R2, and R3, connected in series. When connected to an ideal emf source E1, current I1 flows through the resistors. a. If the resistors are instead connected to a second source with E2=2E1, what is the new current through the resistors in terms of the first current? b. Show that, if each resistance is doubled and the resistors are connected in series to the second emf source, the current through the resistors is equal to I1.
. An electric car is being designed to have an average power output of 4,000 W for 2 h before needing to be recharged. (Assume there is no wasted energy.) (a) How much energy would be stored in the charged batteries? (b) The batteries operate on 30 V. What would the current be when they are operating at 4,000 W? (c) To be able to recharge the batteries in 1 h, how much power would have to be supplied to them?
The human body can exhibit a wide range of resistances to current depending on the path of the current, contact area, and sweatiness of the skin. Suppose the resistance across the chest from the left hand to the right hand is 1.0 106 . (a) How much voltage is required to cause possible heart fibrillation in a man, which corresponds to 500 mA of direct current? (b) Why should rubber-soled shoes and rubber gloves be worn when working around electricity?
Unreasonable Results (a) What current is needed to transmit 1.00 102 MW of power at 10.0kV? (b) Find the resistance of 1.00 km of wire that would cause a 0.0100% power loss. (c) What is the diameter of a 1.00-km-long copper wire having this resistance? (d) What is unreasonable about these results? (e) Which assumptions are unreasonable, or which premises are inconsistent?