An ideal Diesel cycle has the air inlet temperature and pressure of 21 °C and 92 kPa respectively. The compression ratio is 22:1 while the maximum cycle temperature is 1200 ºc. the diagram ithat represents this process is the process 1-2 on this diagram is the process 2-3 on this diagram is the process 3-4 on this diagram is the process 4-1 on this diagram is Use the followng words to answer B-E: rejection, supply, expansion, compression, heat, isentropic, constant, pressure, volume, temperature

An ideal Diesel cycle has the air inlet temperature and pressure of 21 °C and 92 kPa respectively. The compression ratio is 22:1 while the maximum cycle temperature is 1200 ºc. the diagram ithat represents this process is the process 1-2 on this diagram is the process 2-3 on this diagram is the process 3-4 on this diagram is the process 4-1 on this diagram is Use the followng words to answer B-E: rejection, supply, expansion, compression, heat, isentropic, constant, pressure, volume, temperature

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. In an ideal air-standard Otto cycle, the initial conditions are 1 bar and 300 K. The compression ratio is 12:1, and the maximum cycle temperature is 2500 K. Assuming cp = 1.004 kJ/kg-K & k = 1.4, find: (a) show the cycle in both P-v and T-s diagrams. Clearly label all states and energy transfers. (b) temperature at the end of compression, T₂ in K. (c) heat added during the combustion process in kJ/kg. (d) thermal efficiency of the cycle. (e) net work output from the cycle in kJ/kg.
At the beginning of the compression process of air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and the mass flow rate in the system is 1900 kg/hr. Cp=1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) calculate the thermal efficiency of the cycle in %? 2) which formula should be used to determine the thermal efficiency of the cycle ?
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 1950 K. Determine: (a) the compression ratio, r. (b) the cutoff ratio, rc. (c) the thermal efficiency of the cycle, ?th (%). (d) the mean effective pressure, mep (kPa).
In an air standard brayton cycle, air enters the compressor at 27 degree C and 100 kPa. The pressure ratio is 10, and the maximum allowable temperature is 1350 K. the compressor and turbine efficiencies are 85%, and pressure drops 27 kPa between the compressor discharge and turbine inlet. Determine the pressure and temperature at each state in the cycle, the compressor and turbine work, and the cycle thermal efficiency. Please show the PV and TS diagram. Please show complete formulas and solutions.
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 100 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 2050 K. Determine:(a) the compression ratio.(b) the cutoff ratio.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.
The pressure and temperature at the beginning of compression of a cold air-standard Diesel cycle are 95 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 7.2 MPa and the temperature is 2050 K. Assume constant specific heats evaluated at 300 K.Determine:(a) the compression ratio.(b) the cutoff ratio.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.
1.) In an ideal Brayton cycle, air enters the compressor section at 14.7 psia and 55°F. The pressure ratio is 12. Turbine inlet condition of 1300°F. Draw the P-V and T-S diagrams and determine the following: a. Pressure, specific volume & temperature at each state b. Compression ratio c. Work, per unit mass
Show how an ideal Otto cycle can estimate the operation of a spark ignition piston engine [NOTE: Diagrams may be used to explain this question]
6. Determine the maximum cycle temperature of a diesel cycle working on air-standard conditions. The cycle has a compression ratio of 16 and a cut-off ratio of 2.5. a. 2001.5615 C b. 2001.5616 C c. 2001.5617 C d. 2001.5618 C
7 - In the ideal Diesel cycle, the highest temperature of the air is 2241 K, the compression ratio is 17, and the pre-expansion ratio is 2.2. Assuming the specific heats are constant, which of the following is the temperature of the air at the exhaust outlet? a) 1045.8K B) 889.4K NS) 989.1K D) 814.2K TO) 1119.7 K
A gas turbine power plant working on Brayton cycle as per the following specifications Pressure and temperature of air at inlet to compressor = 1 bar and 10oC Power output of the plant = 8 MW Temperature at inlet to the turbine = 780 oC Pressure ratio = 12 Isentropic efficiency of compressor = 100% Isentropic efficiency of turbine = t(%)= 91 Discuss any three methods to improve performance of the cycle with justification based on the data given in the question
Consider an ideal Rankine thermodynamic cycle with H2O as the working fluid. Draw a clear and fully labelled process flow diagram for the cycle. Enumerate points around the cycle starting at point 1 as feed to the pump. Draw a clear and fully-labelled absolute temperature–specific entropy ( T –s ) diagram for the cycle. Use the same enumeration for the cycle. Briefly describe the states of the working fluid around the cycle and the processes between them.