An ideal refrigeration cycle that has a condenser temperature of 25°C and an evaporator temperature of -25°C. Compute for the work input to the compressor, heat absorbed by the evaporator from the cold space, heat released to the hot space, and the COP of this refrigerator for the working fluid R-410a.

An ideal refrigeration cycle that has a condenser temperature of 25°C and an evaporator temperature of -25°C. Compute for the work input to the compressor, heat absorbed by the evaporator from the cold space, heat released to the hot space, and the COP of this refrigerator for the working fluid R-410a.

Name: An ideal refrigeration cycle that has a condenser temperature of 25°C
Uploaded: 2022-11-23T13:49:29.000Z
Channel: Bartleby
Description: An ideal refrigeration cycle that has a condenser temperature of 25°C and an evaporator temperature of -25°C. Compute for the work input to the compressor, heat absorbed by the evaporator from the cold space, heat released to the hot space, and the C

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 20RQ: Welded ______sealed compressors are normally used in household refrigerators.

See similar textbooks

Similar questions

at a stage in a reaction turbine, the mean blade ring diameter is 1 m. the turbine runs at 3000 rpm. the blades are designed for a degree of reaction of 50% with exit angles of 30° and inlet angles of 50°. the turbine is supplied with a steam at 10000 kglh and the stage efficiency is 85%. determine (a) power output of the stage, (b) specific enthalpy drop in kj/kg, (c) percentage increase in relative velocity of steam over moving blades, (d) the specific steam consumption
An impulse steam turbine with a nozzle effeciency 0.9, blade velocity ratio 0.5 and mean blade velocity 150m/s. Determine isentropic heat drop in the nozzle of an impulse steam turbine.
Help me explain the derivation of thermal energy of the Stirling cycle
A turboprop engine consists of a diffuser, compressor, combustor, turbine, and nozzle. The turbine drives a propeller as well as the compressor, delivering a net power of 1 MW to the propeller. Air enters the diffuser at 8000 m altitude (Ta = 236K, pa = 36 kPa) with a velocity of 550 km/h, and decelerates essentially to zero velocity. The compressor pressure ratio is 5.3 and the compressor has an isentropic efficiency of 83%. The turbine inlet temperature is 1360 K, and its isentropic efficiency is 86%. The turbine exit pressure is 10 kPa higher than the ambient pressure at that altitude. Flow through the diffuser and nozzle is isentropic. Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Using an air-standard analysis, determine: a) The mass and volumetric flow rates entering the diffuser, in kg/s and m3/s, respectively.b) The rate of heat addition to the combustor, in MW.c) The velocity at the nozzle exit, in m/s.
Help me explain the derivation of thermal efficiency of the Stirling cycle.
In a reaction turbine, the drum diameter is 2.15 m, speed of turbine is 750 rev/min and the steam flow is 14.2 kg/sec. At a particular ring of blades, the blade height is 15.875 cm and the discharge angle (α & ϕ) is 25°. Here, the pressure of steam is 0.04 N/mm2 abs, and its dryness fraction is 0.97. Determine the following: 2. Heat drop, in kJ, through this turbine pair, assuming turbine efficiency of 80%
Dual cycle's four processess in P-V and t-s DIAGRAM, explanation, equations, efficiency derivation, advantages and disadvantages
Describe the Carnot cycle.
Explain why a certain amount of thermal energy rejected intentionally incondensers and pumps are employed instead of compressors in steam power cycles?
Air enters the compressor of a regenerative gas-turbine engine at 100 kPaand 300 K and is compressed to 800 kPa. The regenerator has aneffectiveness of 65 percent, and the air enters the turbine at 1200 K. For acompressor efficiency of 75 percent and a turbine efficiency of 86 percent,determine(a) The heat transfer in the regenerator.(b) The back work ratio.(c) The cycle thermal efficiency
A steady-flow system operating on the ideal Ericsson cycle can achieve the Carnot efficiency. One of the salient features of this cycle is the isothermal expansion through a heated turbine, as shown in Fig. a. Heat is added to the turbine such that the outlet temperature is equal to the inlet temperature, i.e. T₁=T₂, and the overall pressure ratio for this process is rₚ=P₁/P₂. However, an isothermal expansion through a heated turbine is very difficult to achieve in practical engineering applications. An alternate approach is two use a multi-stage expansion process with reheating. In this approach, the gas expansion process is carried out in multiple stages with reheating in between each stage. Consider the two-stage turbine expansion with reheating shown in Fig. b. The gas enters the first stage of the turbine at state A1, is expanded isentropically to an intermediate pressure Pₐ₂, is reheated at constant pressure to state B1, and is expanded in the second stage isentropically to the…
A steady-flow system operating on the ideal Ericsson cycle can achieve the Carnot efficiency. One of the salient features of this cycle is the isothermal expansion through a heated turbine, as shown in Fig. a. Heat is added to the turbine such that the outlet temperature is equal to the inlet temperature, i.e. T₁=T₂, and the overall pressure ratio for this process is rₚ=P₁/P₂. However, an isothermal expansion through a heated turbine is very difficult to achieve in practical engineering applications. An alternate approach is two use a multi-stage expansion process with reheating. In this approach, the gas expansion process is carried out in multiple stages with reheating in between each stage. Consider the two-stage turbine expansion with reheating shown in Fig. b. The gas enters the first stage of the turbine at state A1, is expanded isentropically to an intermediate pressure Pₐ₂, is reheated at constant pressure to state B1, and is expanded in the second stage isentropically to the…