An ideal vapor compression refrigeration cycle with R-134a as the working fluid operates between the pressure limits of 120.0 kPa and 1.0 MPa. The mass fraction of the refrigerant that is in the liquid phase at the evaporator inlet is

An ideal vapor compression refrigeration cycle with R-134a as the working fluid operates between the pressure limits of 120.0 kPa and 1.0 MPa. The mass fraction of the refrigerant that is in the liquid phase at the evaporator inlet is

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter28: Special Refrigeration Applications

Section: Chapter Questions

Problem 15RQ: Why is two-stage compression popular for extra-low-temperature refrigeration systems?

See similar textbooks

Similar questions

A simple saturation cycle using ammonia between pressures of 10 psia and 165 psia is to be replaced with two stages of compression and water intercooling of vapor from the first stage to 50 OF as entering temperature to the second stage . For the same stroke and working characteristics in both stages , what would be the ratio of the cylinder diameters of the first stage to the second stage . A) 1.75 B) 2.95 C) 1.95 D) 2.75 With diagram
An amonia vapor Refrigeration cycle operates at an evaporator temperature of -16°C and a condesing temperature of 32°C. Determine the coefficient of performance (a) for an ideal saturation cycle, (b) for wet compression with saturated vapor leaving the compressor, and (c) if the vapor at suction to the compressor is superheated 6 degrees.
If an ideal refrigeration cycle (using R-134a) operation at evaporator temperature -10 °C and Condenser temperature +30 °C, what is the dryness factor of the Refrigerant at entering evaporator?
A steam power plant operates on an ideal reheat Ran¬kine cycle between the pressure limits of 15 MPa and 10 kPa. The mass flow rate of steam through the cycle is 12 kg/s. Steam enters both stages of the turbine at 525°C. The moisture con¬tent of the steam at the exit of the low-pressure turbine is not to exceed 5 percent.Show the cycle on a T-s diagram with respect to saturation lines. determine:(a) the pressure at which reheating takes place, (b) the total rate of heat input in the boiler, and(c) the thermal efficiency of the cycle.
The events of the Frick, split -stage , low temperature refrigerating cycle are as follows : AFreon-12 vapor compression system operates between O deg F and 90 deg F with saturatedliquid on the high side of the expansion valve and saturated vapor entering the compressorwhose volumetric efficiency is 88% . An NH3 compression operates between -63.11 deg F and11.66 deg F with saturated liquid entering the expansion valve and saturated vapor enteringthe compressor whose volumetric efficiency is 85% .The Freon -12 evaporator serves as thecondenser for the NH3 . For the ideal cycle and 1 ton of refrigeration , find the totalhorsepower required for compression efficiencies of 85% .A) 2.187 B) 2.96 C) 3.96 D) 1.6
A rankine cycle with three stages of reheating is executed with steam expanding initially from 18.111 Mpa and 540oC. The pressure of three reheaters are 4.0111 Mpa, 2.5111 Mpa and 0.98111 Mpa, and the steam leaves the first reheater at 500oC, the second 480oC. Condensation occurs at 0.4111 Mpa. Calculate W,ec, and ee.
Drow the h-s diagram of the actual and isentropic processes of an adiabatic nozzle.
Steam at 10 MPaa, 550 degrees Celsius enters an ideal enginethat has one stage of regenerative cycle; condenser pressure is 10 kPaa and extraction of steam is at 1 MPa
In a steam power plant, the condenser pressure is 10 kPa. The turbine and pump isentropic efficiencies are both 85 %. Draw the schematic and T-S diagrams. Label the points by setting point 1 at the condenser outlet, point 2 at the pump outlet, point 3 at the boiler outlet, and point 4 at the turbine outlet. Use the label 2a and 4a for the points due to the isentropic efficiency of the pump and turbine, respectively. Use 2 decimal places for the enthalpy and other energies in solving and for the final answers. For the steam quality (x) and entropy (s), use 4 decimal places in solving. For the specific volume, use 6 decimal places. The pressure and the temperature of steam that enters the turbine are 4.5 MPa and 800 oC Determine the following: (INPUT YOUR ANSWERS ON THE BLANK SPACES PROVIDED.) Enthalpy at point 1 in kJ/kg = Enthalpy at point 2 in kJ/kg = Enthalpy at point 3 in kJ/kg = Enthalpy at point 4 in kJ/kg = Actual Enthalpy at point 2a in kJ/kg = Actual Enthalpy at point…
A 330 MW steam power plant operates according to the simple ideal Rankine cycle. Water vapor enters the turbine at a pressure of 10 MPa and a temperature of 525 ° C and expands to a condenser pressure of 15 kPa. Show the cycle in a T-s diagram with the saturated liquid and saturated vapor curves and calcualte the; a)The degree of dryness of the steam at the turbine outlet. b)Thermal efficiency of the cycle. c)The mass flow of water vapor circulating in the cycle.
In a Refrigerant 12 system which serves a 212 kw evaporator at - 30 0C. The system uses two stage compression with intercooling and removal of flash gas. The condenser temp is 400C . Given that, h2=356kJ/kg, h4=367kJ/kg Compute the following: a.) mass flow rate at low stage compressor (m1)ANSWER: 1.53661 kg/s b.) mass flow rate at high stage compressor (m3)ANSWER: 2.11791 kg/s c.) low stage compressor workANSWER: 27.43931 kw d.) high stage compressor workANSWER: 32.63926 kw e.) total compressor workANSWER: 60.078575 kw f.) COPANSWER: 3.52871 g.) heat rejected in the condenserANSWER: 272.07857 kw
The pressure in the boiler of a steam power plant operating on the ideal Rankine cycle is 1250 psia. The condenser pressue is 2 psia. The mass flow rate of steam through the system is 75 lbm/s and the quality of the steam at the turbine exit is 0.9. Show the cycle on a T-s diagram, and determine (a) the turbine inlet temperature, (b) the rate of heat input in the boiler, and (c) the thermal efficiency of the cycle.