An impeller (axial-flow turbine propeller) in an agitated tank has an output torque (T) whose dimension is ML2/T2 which is proportional to the volumetric flow rate (Q) and also depends upon the density (ρ), rotor diameter (D), and rotation rate (N). Perform Dimensional Analysis.

An impeller (axial-flow turbine propeller) in an agitated tank has an output torque (T) whose dimension is ML2/T2 which is proportional to the volumetric flow rate (Q) and also depends upon the density (ρ), rotor diameter (D), and rotation rate (N). Perform Dimensional Analysis.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.13P: 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its...

See similar textbooks

Related questions

Q: pressure line and a sus specific entropy snocific hoat

A: solution of above question is below:

Q: The pressure in an automobile tire depends on the temperature of the air in the tire. When the air t...

A: To solve this problem, we have used ideal gas equation. we calculated mass of air for condition 1 an...

Q: A suppressed weir (C = 1.84) under a constant head of 90mm feeds a tank containing a 75 mm diameter ...

Q: A sub-marine with its axis 15 m below water surface fitted with pitot tube moves horizontally in sea...

A: We must determine the speed of a sub-marine with an axis 15 m below the water surface and a pitot tu...

Q: hydraulic lift is to be used to lift a truck weighing 5000 lb. What is the pressure (gage) must be a...

A: Given:W=5000 lbd=12 in

Q: A soap bubble with a diameter of 2.28" is to be enlarged by blowing air into it. If the surface tens...

Q: A cylindrical pipe with water flowing downward at 0.02 cubic m/s having top diameter of 0.08, bottom...

Q: Compute for the composition, in atom percent, of an alloy that consists of 92.5 wt% Ag and 7.5 wt% C...

A: Consider the alloy sample has a mass of 100 g. Then according to the problem, the 100 g alloy sample...

Q: Determine the stress acting in members AB, BD and BE of th members is 15 in2

A: Need to determine Stress.

Q: soap bubble with a diameter of 2.03" is to be enlarged by blowing air into it. If the surface tensio...

A: Given:d1=2.03 inσ=0.0041 lbf/ftd2=4.85 in

Q: The roller track is to be swiveled by means of a double-acting cylinder. The signals to extend and t...

A: Draw the pneumatic circuit diagram using ISO symbols and connecting the ports with solid lines.

Q: 2. The 1-m diameter cylinder in the figure is 8 meters long (dimension perpendicular to the paper) a...

A: Static Equilibrium Static harmony alludes to any framework where the amount of the powers, and force...

Q: (a) Two simple harmonic vibration acting at right angles to each other have the time period in the r...

A: SIMPLE HARMONIC MOTION In mechanics and material science, straightforward consonant movement (at tim...

Q: A venturi tube is used to determine the airspeed at the throat/test section. During the test, a rais...

Q: Outside air at 95°F DB and 0.0168 Ibs/lb Humidity Ratio is mixed with air returning from a room at 7...

Q: A 6.2m diameter balloon is filled with helium at 24°C and 183.18kPa. Determine the mass of the heliu...

Q: An open cylindrical tank 1.2 meters in diameter and 2.1 meters high is 2/3 full of water. After rota...

Q: The position of a particle along a straight line is given by s = (1.5t3 – 13.5t2 + 22.5t), where t i...

Q: Explain any one type of ball bearing with a neat diagram and write their applications?

Q: Solve for the ratio of the initial to final speed of sound if an air expands isentropically from 164...

Q: 3 We covered the idea of a streamfunction in Cartesian (x, y) coordinates. In a similar fashion, whe...

Q: A steel shaft 8 ft long that has a diameter of 5 inches is subjected to a torque of 47 kip ft. Deter...

Q: The 2.4-Mg car increases its speed uniformly from rest to 22 m/s in 38 s up the inclined road. (a) D...

Q: A 4ft long rod with a 0.29 inch diameter is subjected to a 10,130lb tensile load. What is the tensil...

Q: ected to torsion by torques T applied at the ends (see figure). The bar is 10 in. long, and the insi...

Q: A rectangular plate 20-kg is supported by three cables as shown etermine: 1.1 Drawing Free-Body-Diag...

Q: 2. The 1-m diameter cylinder in the figure is 8 meters long (dimension perpendicular to the paper) a...

Q: 180 mm |T2 T1 T

A: Givenμ=0.2m=20kg

Q: roller coaster car has mass of 880 kg and has a speed that increases at a = (6.0 – 0.04 s) m/s, wher...

Q: A wheel tractor has a 200 HP engine. Calculate the available rimpull of this tractor if it is operat...

Q: Which one of the following expressions for v is valid?

A: Given; The velocity field of an incompressible flow in a Cartesian system,It is represented by: V→=...

Q: A 50-mm-diameter aluminum compound shaft is loaded by torques at the gears as shown in the figure. D...

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces sho...

A: To determine the moment and rection about point A.

Q: 1 Awall bracket, as shown in Fig, is subjected to a force P = 5 kN, The cross-section of bracket is ...

Q: An 8 in-diameter air compressor is operating with a maximum pressure of 10 psi. The bolts have a yie...

Q: 1.5 m The rigid L-shaped member ABC is supported by a ball-and-socket joint at A and by three cables...

Q: For a profit-maximizing monopoly that charges the same price to all consumers, what is the relations...

A: A profit maximizer is a vital feature of a monopolist. There is no competition in a monopolistic ...

Q: Determine the maximum diameter of a ball floating on water at 20°C if it has a density of 5060 kg/m3...

A: It is required to determine max diameter of ball

Q: Omar, a Professional Engineer (P. Eng.) with many years of experience and a valid Certificate of Aut...

A: 1. The issue here is that the design is free of flaws or defects, but the correct installation is no...

Q: A solid circular shaft 2.5 m long and 75 mm in diameter is subjected to torsional moment. Use G=78 G...

Q: 4. A differential band brake is shown in the figure. The diameter of the drum is 800 mm. The coeffic...

Q: Calculate the dynamic viscosity of an oil, which is used for lubrication between a square plate of s...

Q: The two blocks started at rest. The surface of the inclined plane is frictionless. (note: neglect ma...

A: Given:WA=300 lbWB=400 lb

Q: The initially closed valve in Figure III..6.1(b) suddenly opens. Find the flow velocity 5 seconds af...

Q: Use the plot command to plot the function f(x) = (0.5x* +1.1x -0.9x²)e-07* for -3<x<10.

A: Code for the plotting of f(x);% The range of the function is -3 to 10. x=-3:1:10; % The given equati...

Q: A 1000 kg homogenous bar 2 m long is suspended horizontally from two vertical cables A and B each 1...

A: Given Datam=1000kgA=400m2σA=100MPaσB=50MPa I had Given Required figure

Q: Determine the pressure difference between the inside and outside of the 0.13 mm diameter air bublle ...

Q: For the beam and loading shown, determine the absolute values of the shear and bending moment at 2.5...

Q: A copper tube with wall thickness of 8 mm must carry an axial tensile force of 175 kN. The allowable...

Q: Match the following non-dimensional numbers with the corresponding definitions: Non-dimensional numb...

A: GIVEN DATA - MATCH THE FOLLOWING GIVEN OF NON-DIMENSIONAL NUMBER WE HAVE TO MATCH IT CORRECTLY

Question

An impeller (axial-flow turbine propeller) in an agitated tank has an output torque (T) whose dimension is ML²/T²which is proportional to the volumetric flow rate (Q) and also depends upon the density (ρ), rotor diameter (D), and rotation rate (N). Perform Dimensional Analysis.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.
The radius R of a mushroom cloud generated by a nuclear bomb grows in time. We expect that R is a function of time t, initial energy of the explosion E, and average air density ? . Use dimensional analysis to express the relationship between R, t, E, and ? in dimensionless form.
Dimensional analysis is to be used to correlate data on bubble size with the properties of the liquid when gas bubbles are formed by a gas issuing from a small orifice below the liquid surface. Assume that the significant variables are bubble diameter D, orifice diameter d, liquid density rho, surface tension sigma (in N/m), liquid viscosity mu, and g. Select d, rho, and g as the core variables.
The period of a pendulum T is assumed to depend only on the mass m, the length of the pendulum `, the acceleration due to gravity g, and the angle of swing θ. By means of dimensional analysis, simplify this problem and express this dependence in nondimensional terms.
The thrust F of a propeller is generally thought to be afunction of its diameter D and angular velocity V , the forwardspeed V , and the density ρ and viscosity μ of the fl uid.Rewrite this relationship as a dimensionless function.
The speed of sound c in an ideal gas is known to be a function of the ratio of specific heats k, absolute temperature T, and specific ideal gas constant Rgas. Showing all your work, use dimensional analysis to find the functional relationship between these parameters.
The force, F, acting on a billboard due to wind depends on it length, l, height, h, the modulus of elasticity of the board, E, and the specific weight, γa, of the air. Using dimensional analysis, find an appropriate dimensionless relationship.
The speed of sound c in an ideal gas is known to be a function of absolute temperature T, universal ideal gas constant Ru, molar mass (molecular weight) M of the gas, and ratio of specific heats k. Showing all your work, use dimensional analysis to find the functional relationship between these parameters.
List the three primary purposes of dimensional analysis.
An automobile has a characteristic length and area of 8 ft and 60 ft2, respectively. When tested in sea-level standard air, it has measured velocities of 20, 40, and 60 mi/h and drag forces of 31, 115, and 249 lbf, respectively. The same car travels in Colorado at 115 mi/h at an altitude of 3500 m. Using dimensional analysis, estimate its drag force (in lbf). Using dimensional analysis, estimate the horsepower required to overcome air drag (in hp)
The output power W. of a spinning shaft is a function of torque T and angular velocity ? . Use dimensional analysis to express the relationship between W., T, and ? in dimensionless form. Compare your result to what you know from physics and discuss briefly
The pressure coefficient is defined by the ratio between the static pressure difference and the dynamic pressure (pictured): Where P is the static pressure [Pa], P∞ is the reference static pressure [Pa], ρ is the density [kg/m3], and V is the velocity [m/s]. Using the primary dimensions and their units, show that the pressure coefficient is dimensionless.