Question

Fluid Mechanics Question

An incompressible fluid flows in the converged nozzle provided in the figure.

nozzle area -> A=Ao*(1-b*x)

entry speed -> V=Vo*(0.5+0.5*cos(w*t))
Vo:20m/s
Ao=1.5 m2
L=13m
b=0.2/22
W=0.16rad/s
Find the acceleration in the nozzle center as a function of time
 
* (to multiplication)
/ (to divide)
 
 
 
 
Expand

Expert Answer

1 Rating

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Fluid Mechanics

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: The nature of surfaces affects the absorption and the reflection of radiation. Assume that you are g...

A: The black painted piece of wood will absorb more heat when the given two pieces of the wood used for...

Q: Home Work 2 The articular Cartilage is subjected to plane stress ith normal stresses ox, Oy and shea...

A: Write the expression of the normal stress developed on an oblique surface when θ = 30°.

Q: Using Maximum shear stress theorem, determine the factor of safety at point H, on the surface of the...

A: Consider the sectional diagram of the beam at H, Here, M2 and M3 are the bending moments due to for...

Q: Determine the total support reactions at A and 8 for the truss loaded below. -5 at 3 m- 15 m- 12 AN ...

A: Click to see the answer

Q: Water vapor at a flow rate of 20000 kg / hour enters a steam boiler with a specific volume of 150 kP...

A: Given data: The specific volume of the water vapour at 150 kPa is nearly equal to the specific volu...

Q: Explain why a 92% copper – 8% nickel can or cannot be age hardened. Please solve Urgent!!!

A: Age hardening is a heat treatment process that is used to increase the yield strength of malleable m...

Q: A circular Euler column with one end fixed and the other pinned (or hinged or simply-supported) is u...

A: Let us consider a column AB of length L and uniform cross sectional area fixed at the end A and hing...

Q: The mass of crate D is held in position by two blocks, B and C, which are attached to the ring at A....

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If y...

Q: The solid shaft has a diameter of 0.85 in . It is subjected to the torques shown in the figure below...

A: Click to see the answer

Q: Please help me

A: Hello, since the question has multiple sub-parts and you did not specify which parts are needed to b...

Q: Air at 80 kPa and 127°C enters an adiabatic diffuser steadily at a rate of 6000 kg/h and leaves at 1...

A: Click to see the answer

Q: Engineering Mechanics (Equilibrium):   The mass of the uniform bar AB is 40kg. Calculate the couple ...

A: Click to see the answer

Q: 30.13 A stent is used to "prop up" a clogged artery to allow blood to pass through it. But stents ca...

A: Click to see the answer

Q: Refrigerant-134a at 800 kPa and 25°C is throttled to a temperature of 20°C. Determine the pressure a...

A: Note: The temperature after the throttling process should be -20 degrees Celsius.   The enthalpy of ...

Q: Question 4 2 Your answer is partially correct. Try again. Determine the reactions at A and B for the...

A: Click to see the answer

Q: Q4. Obtain i, in the instrumentation amplifier circuit 6.98 Vo 40 K2 20 ka www ww 20 k 7V 40 k2 Q5. ...

A: Click to see the answer

Q: Please help me

A: Consider the free body diagram shown below for the given system. Here, x is the displacement of the...

Q: 1)a) Why is automation of the covered electrode arc source difficult?b) what properties is a metal w...

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: A gable frame is subjected to a wind loading, as shown. Determine the reaction components at its sup...

A: Click to see the answer

Q: A small centrifugal pump is used to deliver 0.005 m/s of water to level 2 as shown in Fig. 2. Neglec...

A: Click to see the answer

Q: As a researcher in the field of heat transfer, how will you distinguish between radiation by black b...

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: Define process cycle time

A: Process Cycle Time: Process cycle time is the time of a product that takes on a work station. When t...

Q: A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and tempe...

A: Assumptions related to the design parameters of the cooker are: The total volume of the cooker (V) =...

Q: In the beam given with the section; a) Calculate the location and value of the maximum tensile and s...

A: Click to see the answer

Q: 5.5-18 Determine the maximum tensile stress o, and maximum compressive stress o due to the load P ac...

A: Click to see the answer

Q: Given that, h = [0.1a] m, P = [10a] kN,-4 2 A1 =A2 =A3=2x10 m,E1=E2=E3=2x105 MPa,α=30°.Allthejoints ...

A: Given data as per the question A1 =A2 =A3=2x10-4 m2  P = [10a] kN, E1=E2=E3=2×105 Mpa α = 300 calcul...

Q: (a) Steam at 20 bar and 375 °C expands reversibly in a perfectly thermally insulated cylinder behind...

A: Draw the PV and Ts diagram of the process.

Q: The sketch for the warm water heating system of a studio apartment is shown in the figure. The volum...

A: Given : The volumetric flow rate through the piping system = 0.000162 m3/s The different losses are ...

Q: A gold-alloy microbeam attached to a silicon wafer behaves like a cantilever beam subjected to a uni...

A: Given data:-

Q: Gas turbine may be modified to be used for propulsion usage as for turbo jet-engine and prop-engine,...

A: The Brayton cycle is an ideal jet-propulsion cycle. The ideal jet-propulsion cycle is known as the r...

Q: ID=114629

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: 19) In fabrication process, steel components are formed hot and then quenched in water. Consider 2 m...

A: Click to see the answer

Q: Air at 100 kPa and 280 K is compressed steadily to 600 kPa and 400 K. The mass flow rate of the air ...

A: The initial condition is given as, The final condition is given as, The heat loss is given as, Th...

Q: The figure below shows a rectangular OB element made of 0.5 cm thick aluminum sheet, attached to the...

A: Click to see the answer

Q: 15-23. The motor exerts a force F on the 40-kg crate a shown in the graph. Determine the speed of th...

A: From the graph, the force equation can be determined as, Consider the free body diagram of the pull...

Q: m = 40 kg 4) Determine the magnitude and direction of the friction force which the vertical wall exe...

A: Click to see the answer

Q: Determine the member forces in eachmember of the the truss and state if they arein tension or compre...

A: Click to see the answer

Q: You are a structural Engineer who works in Dar Al Handasah company. Your manager has called for a me...

A: As the question is having more than three sub parts, first three are solved.

Q: An inventor claims that he can generate power from the hot spring of Ain Akisfah in Rustaq which its...

A: Click to see the answer

Q: The mass moment of inertia of a helicopter’s rotor is 5000 ???2. The rotor starts from rest at ? = 0...

A: Click to see the answer

Q: The 10-kg block is subjected to the forces shown. In each case, determine its velocity when t = 2 s ...

A: Click to see the answer

Q: 5.5-21 A cantilever beam, a UPN 300 section, is subjected to its own weight and a point load at B. F...

A: Click to see the answer

Q: Find the applied force to CK element which is in the cage system 1.5m 15m 15m 15m 1m -3m M 2.25 m 15...

A: Click to see the answer

Q: Using the table below:a. Develop separate schedules using the SPT and EDD rules.b. Compare the two s...

A: Click to see the answer

Q: A water heater supplies (25)kw of power in the form of heat to water. If the(323)kg of water is heat...

A: The specific heat of water is given as, The heat required to heat the water from -5 oC to 55 oC is ...

Q: A piston-cylinder arrangement contains air at pressure of 1 MPa and expands according to a process r...

A: Click to see the answer

Q: The mass moment of inertia of a helicopter’s rotor is 5000 kgm2. The rotor starts from rest at t=0. ...

A: Click to see the answer

Q: Fluid mechanics problem

A: Write the expression of the velocity of water in the pipe. Write the expression of the frictional h...

Q: Body A with a mass of 10 kg is in balance in the middle of the inclined plane with the help of the A...

A: The vector diagram of the above system is given as, The co-ordinates of point A is written as, The...

Q: Draw the load (FBD) and the bending moment diagrams that correspond to the given shear force diagram...

A: we know that in SFD for UDL there is an inclined line. Sign convection taken for shear force Sign ...