An op-amp comparator in a firing circuit can produce waveforms at the output of up to 28 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +14 to -14 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is 5.92 volts, the delay angle (in degrees) would be:

An op-amp comparator in a firing circuit can produce waveforms at the output of up to 28 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +14 to -14 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is 5.92 volts, the delay angle (in degrees) would be:

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter11: Thermostats, Pressure Switches, And Other Electric Control Devices

Section: Chapter Questions

Problem 23RQ

See similar textbooks

Similar questions

A clamping circuit has to have an independent source, a diode, a resistor, and a capacitor. To keep a constant voltage on the capacitor over the period of the input, the RC time constant must be large. A design rule of thumb is to make the RC time constant at least five times the half period of the input signal. Why do we need to make the RC time constant at least five times the half period of the input signal greater? Is having a 2, 3, or 4 times RC time constant, not enough?
One way to control power, in an electronic system is to using the PWM (pulse width modulation) method. To create an adjustable signal pulse width, one of which is used a window comparator as shown in the figure (VCC = +12 V, VEE = -12 V). If a 10 Vpp 10 kHz signal is given as an input, determine the complete output waveform by displaying the reference voltage. (compare with the input)
Given a inverting op-amp with Vin= 1Vpk,1kHz and Rin=1kΩ , Rf=10kΩ, VEE=-5V, VCC= 5V, Explain the output waveform, why does the wave became square (Blue wave).
A sinusoidal signal of 2 kHz frequency is applied at the input of a delta modulator with a step size of 0.1 volt. The sampling rate of the delta modulator is 20000 samples per second. What will be the maximum amplitude of the sinusoidal signal if there is no slope overload distortion?
13. The purpose of the __________ is to periodically sample the continuallychanging analog signal and covert those samples to a series of constantamplitude pulses that can more easily be converted to binary PCM.14. In ___________, the input analog waveform is sampled by a sampling pulsewith an output waveform that is flattened at the top.15. The simplest form of pulse modulation is ______________.
Multiple Choice directions: Circle the letter of the answers that best answer the question. 13. When using microwave tubes as amplifiers, what is used as bandpass filters? a. Transistors b. Oscillator c. All of the above d. Power tubes 14. The microstrip lines used to achieve maximum power transfer are intended for a. Signal coupling b. Decoupling to prevent feedback c. Low-noise amplification d. Impedance matching and tuning 15. A diode that when reverse biased will momentarily and will abruptly turn off. a. Varactor diode b. IMPATT c. Step recovery diodes d. PIN diodes 16. A microwave transmission line used to minimize noise and crosstalks. a. Stripline b. Hard line cable c. Waveguide d. Microstrip 17. The major difference between a low frequency transistors and microwave types is/are. a. B & C b. Packaging c. Material d. Internal geometry 18. Which of the following band belongs to the millimeter waves a. C b. Ku c. U d. L 19. Overcrowding in the frequency spectrum is prevalent…
Question: What is the maximum frequency of an sine wave with a 1.5V peak amplitude that can be produced at the output terminal of an op-amp that has a slew rate of 0.5V/μs
For an ideal op-Amp differentiator circuit C = 10 uF and R = 10 kohm . If a triangular wave is fed through the input with a voltage rise of 5 V in 50 ms, what would be the magnitude of output voltage? None of the options are accurate Can't be determined from the given information 5 V peak square signal 1 mV peak square signal 10000 mV square signal 100 V peak square signal 1 V peak square signal 0.1 V peak square signal
The output of the op-amp comparator is a --------. a. rectangular waveform b. sinusoidal waveform c. sawtooth waveform
a.Derive the excitation equations b. Determine transition and output equations c. Derive the transition/output table and Draw the state diagram.
A boost converter is required to have an output voltage of 8 V andsupply a load current of 1 A. The input voltage varies from 2.7 to4.2 V. A control circuit adjusts the duty cycle to keep the outputvoltage constant. If the switching frequency is 200 kHz, determine:i. a value for the inductor such that the variation in inductorcurrent is no more than 40% of the average inductor current forall operating conditions.ii. a value for the capacitor such that the output voltage ripple isno more than 2%.iii. in case the OFF period is reduced by 30% for constantfrequency operation, find the new output voltage
Figure 3 shows a Hartley oscillator. Assume that the op-amp employed in the figure is an ideal op-amp, and R1= 20 kΩ, R2 = 60 kΩ, L1=10 mH. b) State the Barkhausen criterion for sustained oscillation.c) Explain briefly how the phase shift requirement for sustained oscillation ismet in the circuit of Figure 3.d) The feedback ratio and oscillation frequency of Figure 3 are givenrespectively by, B = -L2/L1 and w0 = 1 / sqrt(L1 +L2)C Determine the values of C and L2 in order for the circuit to oscillate at a frequency of 200 Hz.