An open-air" parallel plate capacitor is connected to a 11 V power source, which charges each plate with an absolute value of 9.2 mC. While the capacitor is still connected to the power source, a material with a dielectric constant of 5.5 is inserted, completely filling the space in between the capacitor plates. In considering the system of the charges on the parallel plates and the material, how much external** work was done in inserting the material? Give your answer in units of J.

An open-air" parallel plate capacitor is connected to a 11 V power source, which charges each plate with an absolute value of 9.2 mC. While the capacitor is still connected to the power source, a material with a dielectric constant of 5.5 is inserted, completely filling the space in between the capacitor plates. In considering the system of the charges on the parallel plates and the material, how much external** work was done in inserting the material? Give your answer in units of J.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter8: Capacitance

Section: Chapter Questions

Problem 48P: A parallel-plate capacitor is made of two square plates 25 cm on a side and 1.0 mm apart. The...

See similar textbooks

Similar questions

The dielectric to be used in a parallel-plate capacitor has a dielectric constant of 3.60 and a dielectric strength of 1.60107 V/m. The capacitor has to have a capacitance of 1.25 nF and must be able to withstand a maximum potential difference 5.5 kV. What is the minimum area the plates of the capacitor may have?
Earth can be considered as a spherical capacitor with two plates, where the negative plate is the surface of Earth and the positive plate is the bottom of the ionosphere, which is located at an altitude of approximately 70 km. The potential difference between Earth’s surface and the ionosphere is about 350,000 V. (a) Calculate the capacitance of this system, (b) Find the total charge on this capacitor, (c) Find the energy stored in this system.
A capacitor is constructed from two square, metallic plates of sides and separation d. Charges +Q and Q are placed on the plates, and the power supply is then removed. A material of dielectric constant K is inserted a distance x into the capacitor as shown in Figure P20.85. Assume d is much smaller than x. (a) Find the equivalent capacitance of the device. (b) Calculate the energy stored in the capacitor. (c) Find the direction and magnitude of the force exerted by the plates on the dielectric. (d) Obtain a numerical value for the force when x = /2, assuming = 5.00 cm, d = 2.00 mm, the dielectric is glass ( = 4.50), and the capacitor was charged to 2.00 103 V before the dielectric was inserted. Suggestion: The system can be considered as two capacitors connected in parallel. Figure P20.85
A 2.0F capacitor and a 4.0F capacitor are connected in series across a 1.0-kV potential. The charged capacitors are then disconnected from the source and connected to each other with terminals of like sign together. Find the charge on each capacitor and the voltage across each capacitor.
An air-filled capacitor is made from two flat parallel plates 1.0 mm apart. The inside area of each plate is 8.0cm2. (a) What is the capacitance of this set of plates? (b) If the region between the plates is filled with a material whose dielectric constant is 6.0, what is the new capacitance?
A variable air capacitor used in a radio tuning circuit is made of N semicircular plates, each of radius R and positioned a distance d from its neighbors, to which it is electrically connected. As shown in Figure P20.38, a second identical set of plates is enmeshed with the first set. Each plate in the second set is halfway between two plates of the first set. The second set can rotate as a unit. Determine the capacitance as a function of the angle of rotation , where = 0 corresponds to the maximum capacitance. Figure P20.38
A parallel-plate capacitor is connected to a battery. What happens to the stored energy if the plate separation is doubled while the capacitor remains connected to the battery? (a) It remains the same, (b) It is doubled. (c) It decreases by a factor of 2. (d) It decreases by a factor of 4. (e) It increases by a factor of 4.
A capacitor has parallel plates of area 12 cm2 separated by 2.0 mm. The space between the plates is filled with polystyrene, (a) Find the maximum permissible voltage across the capacitor to avoid dielectric breakdown, (b) When the voltage equals the value found in part (a), find the surface charge density on the surface of the dielectric.
A parallel-plate capacitor is made of two square plates 25 cm on a side and 1.0 mm apart. The capacitor is connected to a 50.0-V battery. With the battery still connected, the plates are pulled apart to a separation of 2.00 mm. What are the energies stored in the capacitor before and after the plates are pulled farther apart? Why does the energy decrease even though work is done in separating the plates?
When a Leyden jar is charged by a hand generator (Fig. 27.1, page 828), the work done by the person turning the crank is stored as electric potential energy in the jar. When a capacitor is charged by a battery, where does the electric potential energy come from?
(i) A battery is attached to several different capacitors connected in parallel. Which of the following statements is true? (a) All capacitors have the same charge, and the equivalent capacitance is greater than the capacitance of any of the capacitors in the group, (b) The capacitor with the largest capacitance carries the smallest charge, (c) The potential difference across each capacitor is the same, and the equivalent capacitance is greater than any of the capacitors in the group. (d) The capacitor with the smallest capacitance carries the largest charge. (e) The potential differences across the capacitors are the same only if the capacitances are the same, (ii) The capacitors are reconnected in series, and the combination is again connected to the battery. From the same choices, choose the one that is true.