an operational amplifier is working as differential amplifier it takes input voltage 41 volt at inverting terminal and 5`1 volt at non inverting terminal. by keeping these voltages find following parameters. evaluate the output voltage for inverting terminal if gain is 3 options a=-113 volt b=-133 volt c=-123 volt d=-143 volt

an operational amplifier is working as differential amplifier it takes input voltage 41 volt at inverting terminal and 5`1 volt at non inverting terminal. by keeping these voltages find following parameters. evaluate the output voltage for inverting terminal if gain is 3 options a=-113 volt b=-133 volt c=-123 volt d=-143 volt

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

Design a differential amplifier stage with Add = 40 dB, Rid ≥ 250 kΩ, and an input commonmode input range of at least ±5 V. Specify a current source to give CMRR of at least 80 dB for a single-ended output. MOSFETs are available with Kn = 50 μA/V2, λ = 0.0133 V−1, and VT N = 1 V. BJTs are available with IS = 0.5 fA, βF = 100, and VA = 75 V.
Suppose that each output channel of a computer’ssound card can be represented by a 1-V ac sourcein series with a 32-Ω resistor. Each channel ofthe amplifier in the external speakers has an inputresistance of 20 k , and must deliver 10 W intoan 8-Ω speaker. (a) What are the voltage gain, currentgain, and power gain required of the amplifier?(b) What would be a reasonable dc power supplyvoltage for this amplifier?
The common-mode gain of the front-end circuit for the instrumentation amplifier is equal to ACM= 1 V/V. If the instrumentation amplifier is not reducing the common-mode signal, then why is the CMRR of an instrumentation amplifier higher than a differential amplifier, in general?
A differential amplifier has a differential gain of 500 and negligible common-mode gain. The input terminals are tied to ground through 1-kΩ resistors having tolerances of ±5 percent. What are the extreme values of the output voltage caused by a bias current of 100 nA? What is the output voltage if the resistors are exactly equal?
In a differential amplifier, we have: Ient(in) = 300nA and Ient(off) = 100nA. Calculate the values of IB1 and IB2. 350nA,250nA
The transistors in the differential amplifier as shown have mismatched transconductances. Calculate Add , Acd , and the CMRR of the amplifierif the output is the differential output voltage υOD, and R = 100 kΩ, gm = 3 mS, Δgm/gm = 0.01, VCC = VEE = 15 V, and REE = 100 kΩ.
True or False Increasing RE improves the CMRR for single-ended output by increasing the differential-mode gain anddecreasing the common-mode gain. Increasing RE reduces the transistor DC currents and increases the DC output voltages. The double-ended output of the differential amplifier is always zero if vs1=vs2 for any value of RE.
What is the voltage gain for the small signall differential amplifier showed in the image. The other is grounded. rπ = 3.5kohms. ICQ = 1.5mA (in case is needed). Beta = 200. Note: for this differential amplifier there is only one input signal at the base of the transistor, the other base of the transistor is grounded.
Assume an operational amplifier is working on inverting amplifier in which it takes input resistance and feedback resistance of 30ohm and 60ohm respectively.If input voltage is applied at 150 volt then examine following parameters. Evaluate the overall gain of amplifier. Options: A)5 B)4 C)2 D)5
Q2.4 Which of the following is true for an ideal difference amplifier?A) The Common Mode Suppression Rate is zero.B) The Common Mode suppression ratio is always negative.C) The common mode gain is zero.D) The differential mode gain is zero.
a. Determine the dc levels for the currents (IB1, Ic, IC1, IE1, IB2, IC2, and IE2) and voltages (VB1, VC1, VE1,and VE2) of the direct-coupled amplifier. b. Determine the value of RE2 if VB2 = 6.38V for the direct-coupled amplifier for part (a).
Which is not the internal circuit of operational amplifier?a) Differential amplifierb) Level translatorc) Output driverd) Clamper