An Otto cycle engine is operating on the following conditions: The pressure and temperature at the beginning of compression are 150 kPa and 300 K, respectively. The maximum pressure and temperature are 5100 kPa and 2900 K. Assume cold air standard. Determine: a. The compression ratio b. The net cycle work, Wnet/m (kJ/kg) c. The cycle efficiency in percent.

An Otto cycle engine is operating on the following conditions: The pressure and temperature at the beginning of compression are 150 kPa and 300 K, respectively. The maximum pressure and temperature are 5100 kPa and 2900 K. Assume cold air standard. Determine: a. The compression ratio b. The net cycle work, Wnet/m (kJ/kg) c. The cycle efficiency in percent.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 1950 K. The compression ratio is 23.24 Find the cutoff ratio, thermal efficiency, and mean effective pressure
The compression ratio of an air-standard Otto cycle is 7.5. P1 = 85 kPa and T1 = 32 Celsius at the startof compression. The highest temperature in the cycle is 960 K, and the mass of air is 3 g. determine the: (a) the heat rejection, in kJ, (b) the network, in kJ (c) the thermal efficiency, and the (d) mean effective pressure, in kPa. Show complete solution.
An SI engine uses a four-stroke Otto cycle with turbocharging that is air-standard. The air-fuel mixture enters the cylinders at 70°C, with a compression ratio of rk = 8. Determine the amount of effort done during the compression stroke.
In a spark ignition engine working on the ideal Otto cycle, the compression ratio is 5.5. The work output per cycle (ie, area of the P-v diagram) is equal to 23.625 x 105 x Vc J. where Vc is the clearance volume in m³ What is the indicated mean effective pressure?
4] A Diesel engine operates on the air-standard cycle and has a displacement of3.5 liters. The engine’s compression ratio is 19, and the cutoff ratio is 2.4. The conditionsat the beginning of compression are 37 oC, 98 kPaa, and 3.7 liters. If the engine operatesat 1500 rpm, determine a) the compression ratio; b) the cycle work; and c) the powereddeveloped.
An Otto cycle operates on 1lb/s of air from 15 psia and 130 F at the beginning of compression. The temperature at the end of combustion is 5,000 R; compression ratio is 5.5. for hot-air standard k=1.32. find (a) T4, OR; (b)P4, psia; (c) Qr, BTU/s; (d) thermal efficiency, and (e) work net in horsepower. (Please provide complete solution and write legibly)
An ideal Diesel engine operates on 1.5 lb of air with a suction state at 14.1 psia and 100 F. The pressure at the end of compression is 475 psia and the cut -off is 6% of the stroke from head -end dead - center. Using air properties (R=53.34 ft-lbf/Ibm-R, k=1.4, Cp =.24, Cv=. 1714 Btu/lbm-R), determine compression ratio, percentage clearance, Qa, Qr, Thermal Efficiency, mean effective pressure.
An SI engine operates on an Otto cycle at 3800 RPM, with maximum cycle temperature andpressure of 3100 K and 7846 kPa. The engine has a compression ratio of 9.8:1, and immediately after combustion there is 0.000622 kg of exhaust gas in eachcylinder.During exhaustblowdown, the average mass flow rate through the single exhaust valve is 0.218 kg/sec. Atthe end of blowdown, cylinder pressure is reduced to exhaust pressure of 101 kPa.Calculate:(a) Temperature in cylinder at end of exhaust blowdown. [K](b) Mass of exhaust gas in cylinder at end of blowdown. [kg](c) Crank angle when exhaust valve opens. [° bBDC]
In an air standard dual cycle two –thirds of the total heat supply occurs at constant volume . The state at the beginning of the compression process is 90kPa and 20°C and the compression ratio is 9. if the total heat supply is2100kJ/kg, Determine the efficiency of the cycle.
The rc of an air-standard dual cycle is 12, and P1 is 14.7 psia, the v1 is 75 in3, T1 is 100 F. During the heat-addition processes, 0.4 Btu is transferred at constant volume and 1.0 Btu at constantpressure. Determine T5.
An ideal diesel cycle has a compression ratio of 30 and a shear ratio of 2. If this cycle produces 300 hp, what is the maximum cycle temperature and heat input. Speed 1500 rpm, atmospheric conditions 100 kPa, 300 K.
Plot the efficiency of Otto cycle for range of compression ratio of 6 to 14. At which compression ratio, the efficiency is maximum?