An radial express feeder used on rural distribution and is connected to a lumped-sum (or concentrated) load at the receiving end. Assume that the feeder impedance is 0.12 + j0.12 p.u. The sending end voltage is 1.05 p.u. and Pr is 1.05 p.u. constant power load, and the power factor at the receiving end is 0.9 lagging. Determine the following a. K (b) Vr (c) ô (d) Ir

An radial express feeder used on rural distribution and is connected to a lumped-sum (or concentrated) load at the receiving end. Assume that the feeder impedance is 0.12 + j0.12 p.u. The sending end voltage is 1.05 p.u. and Pr is 1.05 p.u. constant power load, and the power factor at the receiving end is 0.9 lagging. Determine the following a. K (b) Vr (c) ô (d) Ir

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.30MCQ: Under balanced operating conditions, consider the three-phase complex power delivered by the...

See similar textbooks

Similar questions

Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
Consider a 3-phase delta induction motor that is operating at 120 Hz. The motor (load) impedance, Z_Δ is given as (9+j12)Ω. The line-to-line voltage at the load is, ?_ab=416 ∠30ºVrms. Let the source be wye-connected, and line impedance be negligible. a) Draw the single-phase wye equivalent circuit and label all known parameters numericallyincluding load voltage. b)Determine the rms phase current phasors for each phase. c) Calculate the complex power consumed by the 3-phase load. d) Determine the capacitance value of each capacitor in a 3-phase delta capacitor bank needed to correct the load to a power-factor of 0.9, lagging.
A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 + j10 Ω.a. What is the value of the load impedance when referred to the primary?b. (in A rms) What is the current out of the source?
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
Consider a 3-phase delta induction motor that is operating at 120 Hz. The motor (load) impedance, Z_Δ is given as (9+j12)Ω. The line-to-line voltage at the load is, ?_ab=416 ∠30ºVrms. Let the source be wye-connected, and line impedance be negligible. b)Determine the rms phase current phasors for each phase. c) Calculate the complex power consumed by the 3-phase load. d) Determine the capacitance value of each capacitor in a 3-phase delta capacitor bank needed to correct the load to a power-factor of 0.9, lagging.
Consider an ac network with an ideal transformer (with turns ratio of n:1) shown below where ZL=(1+j0) is the load impedance and Zs=(7−j24). Ideal transformer turns ratio n is chosen so that the average power delivered to the load is maximized. Under this scenario, the average power delivered to the load is given by
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ??.and ??Find the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)