analyzing a process with an average processing time of 1 minute and an interarrival time of 10 seconds. There are 7 servers and CVa is 1.3 and CVp is .80. What is average time in queue? What is the average total flow time? Answer both parts correct to

analyzing a process with an average processing time of 1 minute and an interarrival time of 10 seconds. There are 7 servers and CVa is 1.3 and CVp is .80. What is average time in queue? What is the average total flow time? Answer both parts correct to

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.5: Quality Assurance, Process Planning, And Quality Control

Problem 10RQ: If an X-bar chart graph falls below the LCL or rises above the UCL, a machining process is said to...

See similar textbooks

Related questions

Q: What are the first two areas that should be identified in value stream mapping? (Choose two.)

A: 1st two areas are: The Steps The Bottlenecks

Q: Following data refers to the jobs (P, Q, R, S) which have arrived at a machine for scheduling. The…

A: Given:Shortest possible theory is used to reduce the flow time.

Q: It takes an operator 2 min to service a machine and 0.5 min to walk to the next machine. Each…

Q: What do you think are the limitations of operation/outline process chart? Give 3 limitations and…

Q: The following four jobs must be processed through a three-machine flow shop.MachineJob A B C1 4 262…

A: Here, Minimum time taken in machine C>Maximum time taken in machine B Hence we turn the problem…

Q: A commodity is to be supplied at the constant rate of 200 units per day. Supplies of any amount can…

Q: A product development project is planned to contain the activities shown in the table below, along…

A: CPM diagram is given below.

Q: The table below lists the time estimates and immediate predecessor(s) for each activity in a product…

A: Given Data

Q: The key to profitable operation for project cost control is: To keep the project cost equal to…

A: Project cost: It is the total amount of fund required to complete the project. Types of project…

Q: You are given a line balancing problem with the following diagram. The processing time is above each…

A: given; number of workstation=?cycle time(t)=11line efficiency(η)=?

Q: gy and what is its pro

A: introduction: here we have describe six sigma statergy.

Q: Answer the following problems in Job Sequencing

A: Consider the table shown below. S. No. Machine A Machine B 1 8 7 2 10 15 3 11 10 4 12 14…

Q: In a Dumbbell production line connected with 3 workstation centers with the sum of total tasks time…

A: Given: The number of workstations is, n=3. The value of total task time is, T=155 seconds. The…

Q: are you able to upload a word document for example as a solution to a question?

A: Yes, we can upload a word document.

Q: Write the advantages of Gantt Charts in project Management

A: Gantt chart is a special type of bar chart which is used to represent various important correlations…

Q: An gold & iron plant company has 4 machines available for assignment to 4 tasks in one of its…

Q: The processing times of the jobs are given belo

A: option c.

Q: In production, the decision to "Make" versus "Purchase" is very critical. Discuss how and based on…

A: A make-or-buy decision is an act of choosing between manufacturing a product in-house or purchasing…

Q: Which of the following element is used to meet project objectives in project management, ? O a. Time…

Q: These are the work elements and you are supposed to Prepare flow process chart for regular work…

Q: Suppose you are Maintenance Engineering Technologist and facing some production problem in industry,…

A: Using PDSA plans are developed more systematically, progress on plans is carefully monitored,…

Q: A total of 15-day data was collected for a work sampling study at a mechanized production line which…

A: given data

Q: Six jobs arrived in a sequence as given below: [GATE-2009] Jobs Processing Time (days) I 4 II III 5…

Q: What is Critical Path Method (CPM) and how it is useful in project Management.

A: CPM is basically a procedure of scheduling in which a network diagram is used to depict the entire…

Q: Define process cycle time

A: Process Cycle Time: Process cycle time is the time of a product that takes on a work station. When…

Q: There are five jobs (namely 1,2,3,4 and 5), each of which must go through machines A, B and C in the…

A: To determine the sequence of job operations.

Q: process is

A: Given, Following are the process given for a TD process:Where, During a non-flow TD process (1-2)…

Q: A new generator has been installed. There will be no maintenance cost until the end of the sixth…

A: It is required to calculate the present value of the cost of generator with P500 cost from the year…

Q: Robot Ltd. wishes to maintain en

A: Safety stock= 36.67

Q: In a job shop scheduling problem, all the jobs will have the same sequences.

A: In a job shop scheduling problem, all the jobs will have the same sequences. Answer: True

Q: If all jobs can be processed on all machines, assign the jobs to the machines and find the minimum…

Q: The need of scheduling in the production system is to Select one: O a. Find the project time O b.…

A: Scheduling - It is a process in which arrangement, control, and optimization of workload are done in…

Q: Q1/b -A company needs a certain type of inventory materials in a quantity of 150,000 pieces, the…

A: Given data:

Q: Table 3 shows the process sequence in a production line and its related direct time study data. The…

A: Given: During a time study of processing of a product, it is found that operations performed in…

Q: A flow-line mass production operation consists of six manual workstations. Work units are moved…

A: (a) Given: No. of workstations = 6 Transfer time of each station = 10 sec Cycle Time: The cycle time…

Q: In a factory, the direct cost is also called variable cost because: It is connected with the…

Q: Explain and use the EOQ model for independent inventory demand

A: The economic order quantity (EOQ) refers to the ideal order quantity a company should…

Q: produce washing and dryer machines Ditteret are manufactured by press and ferts for each product The…

A: As per honor code and answering guidelines I can answer 1st question at a time.If you want other…

Q: ssing tim

A: given: Station 1 Processing time:5 min station 2 processing time 3 min station 3 processing time 2…

Question

If you give wrong answer - i will report you... and dislike this

Q1. You are analyzing a process with an average processing time of 1 minute and an interarrival time of 10 seconds. There are 7 servers and CVa is 1.3 and CVp is .80.

What is average time in queue?

What is the average total flow time?

Answer both parts correct to get upvote.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

If an X-bar chart graph is between LCL and the UCL, a machining process is said to be ____________.
please solve in 4o mins i will give you positive feedback
What is an example of a WBS in project management thats a home improvement project? How do you create an AOA or AON diagram of this WBS?
Please help and explain process to solve
Hi. Can you please give some advie here to calculate my problems. regards.
A toy factory is planning to make an additional item, which would be processed in 4 departments. The company is proposing to produce 600,000 units per year, working 250 days per year. The estimates of times made by an industrial engineer are in the table: Departments Times 1 2 3 4 Average processing time (second/part) 8 13 10 50 Average maintenance, time/day (minutes) 20 30 20 15 Average daily setup, time (minutes) 20 15 30 20 Average bookkeeping, time/day (minutes) 10 8 12 5 Machine adjustment, time/day (minutes) 15 10 15 15 Defective items, (% of production) 5 6 4 4 The parts are produced within the departments in a sequential manner (from department 1 to 2 to 3 to 4). Determine the efficiency of each departmental operation if only one shift is operated between 7:30 am-4:30 pm, with a 40 minute lunchbreak and two 10 minute coffee breaks.
The BOM for product A is shown in Figure 11.40, and datafrom the inventory records are shown in Table 11.9. In theMPS for product A, the MPS start row has 100 units in week 3and 200 in week 6. Develop the material requirements planfor the next 6 weeks for items C, D, and E.a. Develop the material requirements plan for the next6 weeks for items C, D, and E.b. What specific managerial actions are required inweek 1?
Consider a line consisting of only one machine. This machine takes on average 4 minutes (te=4 min) to complete a job and Ca2=Ce2=1. The arrival rate of the parts to this machine is 1/8 part/minutes. Assume that there is enough space for only 5 parts between the machines (Hint: the buffer size, b, is 5.) Compute the expected CT of this production line. CT=_________
please solve in 5o mins i will give you positive feedback. i need handwritten solution on pages
A company makes two kinds of door Knobs, standard and deluxe ,the making process cost the company 15$ for the standard and 20$ for the deluxe by making on a grinder and a smoother machines, which they can be run for at most 80 hours a week, each standard one needs 2 hours on the grinder, and 4 hours on the smoother, and each deluxe one needs 4 hours on the grinder and 3 hours on the smoother ,the company sales at 25$,35$ for the standard and the deluxe respectively. To have the profit it wants the company decide to make at least 15 knobs from them at a week, formulate the linear programming model?
A CNC milling machine has a purchase price of £120,000 and it is considered from an accounting standpoint to be depreciated to zero value over a period of 5 years. If the machine is to be used for 2 shifts with each shift working for 37 hours/ week and 45 weeks/ year. What is the machine cost/ hr which must be charged in order to amortise/repay the costs over the 5 year period? To make the calculation simpler, you can assume that over the 5 year period you will be required to pay back 8% interest on the sum borrowed. Express your answer in § / hour rounded up to the nearest penny
The analyst in the Dorben Company wishes to assign a number of like facilities to an operator based on minimizing the cost per unit of output. A detailed study of the facilities revealed the following: Loading machine standard time = 0.30 minutes Unloading machine standard time = 0.25 minutes Walk time between two machines = 0.09 minutes Operator rate = $12.00 per hour Machine rate (both idle and working) = $18.00 per hour Machine cycle time = 1.55 minutes TEC = The Expected Cost a) With your initial estimation, how many machines can be serviced exactly?(please keep a non-integer with three decimal places) b) How much is your TEC per piece if the operator has idle time? (please keep three decimal places) c)How much is your TEC per piece if the machine has idle time? (please keep three decimal places) d) How many of these machines should be assigned to each operator?(please write down a numerical number)