4.The vehicle is designed to combine the feel of amotorcycle with the comfort and safety of an automobile. Ifthe vehicle is traveling at a constant speed of 80 km/h alonga circular curved road of radius 100 m, determine the tiltangle 0 of the vehicle so that only a normal force from theseat acts on the driver. Neglect the size of the driver.

Answered: angle 0 o:

Engineering

Mechanical Engineering

angle 0 o:

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.78P: The chain OA is 25 ft long and weighs 5 lb/ft. Find the maximum force in the chain and the distance...

See similar textbooks

Related questions

Q: is q in < q out in power cycles, heat pump cycles, or refrigeration cycles?

Q: For the discharge coefficient C, What else factors can influence its magnitude besides the diameter

A: Besides the diameter, the other factors that influence the magnitude of discharge coefficient are, 1...

Q: Determine the Miller indices for the planes shown in the following unit cell: ja2 a3 (c)

Q: Why is Selenium the tool of choice for automation testing?

A: selenium is the most used tool for automation testing. Because of the following reasons, It enables...

Q: If you are given the K and n values of two different materials, respectively. Is this information su...

Q: The Rankine cycle with one closed feedwater heater (CFWH). Superheated water vapor enters the turbin...

Q: An alloy of Component A and Component B, which do not react but are miscible in all proportions in ...

A: Phase Diagrams: It is an equilibrium diagram which represents the composition of constituent element...

Q: Determine optimum velocity ?

A: Given: Rotor diameter,d=9 mSpeed,N=2700 rpmNozzle angle,α=300Optimum velocity: It is defined as t...

Q: -) Front panel design is A PCB schematics A wiring and pinout layout A wiring design and electronic ...

A: 7. Ans: First option is correct. (A PCB schematics) Front panel design for PCB schematics.

Q: Tyre mass 5 Kg bearing 170 cm rotunting handle by humon 2 cm please find all the specifications for ...

A: LIFE OF BEARING It is defined as the life of an individual bearing in number of revolution or hours ...

Q: If under standard conditions a certain gas weighs 0.14 lb/ft3, then its corresponding specific volum...

A: To find specific volume of gas

Q: A two-stage, single-acting reciprocating air compressor draws in air at 1 bar and 300 K. The deliver...

A: Given that, X=2 two stage, p1=1 bar,T1=300 K, p3=12 barn=1.3 , m=0.15 kg/sec,cp=1 kJ/kg·K,R=0.287 kJ...

Q: The truss is supported by a pin connection at A and a roller at E. It is loaded as shown. Use the pi...

Q: Find the value of Pressure (MPa), volume (m^3/kg), enthalpy, and internal energy if the T=321 ℃ and ...

A: Given Data T=321°Cs=5.544kJ/kg.K

Q: Your steam has a Data of 5.32 MPa and 325 ℃. Find v, u, h and s.

Q: A pelton wheel is supplied with water under a head of 100 m at the rate 1000 litres/s. The bucket de...

Q: A refrigerating system operates on the reversed Carnot cycle. The higher temperature of the refriger...

A: Given data Refrigeration system works on reversed Carnot Cycle.Higher Temperature of the refrigerant...

Q: (S) Sonic wave of air kg) "M2s 413 = o Z (to a longer liquid KG (M3 950) and quickly sound) 's cm 75...

A: Given DataZair=413 kgm2/sρL=950kgm3VL=750m/s

Q: An U- inside the tube, findl the equation of motion for the oscillafion of diquid if the density of ...

A: Consider a U-tube column of uniform cross-sectional area. mass per unit length = m If h is the tota...

Q: Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load ...

A: Answer: The stress in each of the two vertical rods are: (a) Steel : 185.9158 MPa (Tensile stress). ...

Q: How does changing the diameter of an Orifice Plate affect the discharge coefficient and why?

Q: A 9 ft A = 0.5 in.2 12 ft C A = 16 in.?

A: Find the stresses in each member

Q: 8. Consider an iron bar, of diameter 4 cm and length 1m, with specific heat c = 0.437 J/(g K), densi...

A: The movement of heat down a temperature gradient between two bodies in close physical contact is kno...

Q: A hot steam pipe having an inside surface temperature of 250°C has an inside diameter of 8 cm and a ...

A: GIVEN DATA- A COMPOSITE CYLINDER GIVEN COVERED WITH DIFFERENT INSULATION WE HAVE TO FIND HEAT TRANSF...

Q: 12. A 60 lb suitcase slides from rest 5 meters down the smooth ramp. Determine the distance R where ...

Q: (s) (s + 15)(s² +4s + 100) a. 0 (s + 4)(s² + 2s + 90) b. G(s) =

Q: polypropylene PP rod attached ceiling 200 mm tick , 25 mm width ,3 mm length in loaded with 30 kg . ...

A: Given dimensions of polypropylene rod Thickness = 200 mm Width = 25 mm Length = 3 mm Load = 30 kg C...

Q: A propped cantilever beam is loaded by atriangular distributed load from A to C (see figure).The loa...

A: Given data as per question q0 = 10 lb/ft The length of the beam = 12 ftCalculations from equlibirium...

Q: A propeller shaft for a small yacht is made ofa solid steel bar 104 mm in diameter. The allowablestr...

A: (a) Write the given data. d=104 mmθL=2.083.5G=80 GPa

Q: 1. Why is discharge coefficient always less than 1. 2. What is the difference between discharge co...

A: DISCHARGE release pipe - a line through which liquids can be released. hydrant - a release pipe with...

Q: A buildup of brake dust and dirt between the lining and the drum is the most common cause of a. a. ...

A: A buildup of brake dust and dirt between the lining and the drum is the most common cause of a Score...

Q: The true stress beyond initial yielding

A: Given: In a linearly hardening plastic material. True stress beyond yielding is?Where, True stress i...

Q: An oil radiator has an outside surface area of 0.18 m2 and operates at a surface temperature of 85 d...

A: GIVEN DATA- AREA A=0.18m2 T1=85'C T2=16'C h=38.25 W/m2K

Q: Find the mass in metric tons per day of at -5 °C that would theoretically made in a refrigerating pl...

A: Let's first calculate heat absorbed (Qabs) by CO2 in a day: Qabs = m˙(h1 - h2) h1 = specific enthalp...

Q: Determine the force in members JI of the truss. State if the members are in tension or compression. ...

A: Find the force in member JI

Q: A prismatic object 200 mm thick by 200 mm wide by 400 mm long is weighed in water at a depth of 500 ...

Q: 1. The 10-lb block A travels to the right at VA = 2 ft/s at the instant shown. If the coefficient of...

Q: The higher temperature of a refrigerating system operating at a Reverse Carnot Cycle is 240 °F and t...

A: Higher temperature in the cycle, TH=240oF=388.706 KLower temperature in the cycle, TL=266.483 KRefri...

Q: Consider the system formed by three ideal springs, a rigid rod of negligible mass and a body of mass...

Q: Deturmine M- sy B- IN S = Im * (E). L2 - am • &N. filt) O (t) e0.1t 19 cos t+) -t+ ) 8/15 ¤ (t) : VI...

A: Deriving Equation of motion using Newton's 2nd law.

Q: Determine the total force and location of centre of pressure on one face of the plate shown in Fig. ...

A: Total force, F=ρgAh¯h¯=2+22=3 mF=0.9×1000 kg/m39.81 m/s2π422-123F=62408.52 N,

Q: A composite beam is constructed using a steel plate(0.5 in.x 6 in.) with two wood beams (3in. X 6 in...

A: Given Data The length of the steel plate is: l=0.5 in The breadth of the steel plate is: b=6 in The...

Q: Determine the maximum shearing stress in each springs supporting the rigid bar shown. Neglect the ma...

A: We have a rigid bar pivoted at an end and supported by two rigid springs, with a force of 5 KN actin...

Q: Using 1st Angle Projection, draw the following views for the part shown in below (dimensions need to...

A: According to the details provided in the question, we need to calculate THREE PROJECTION VIEW

Q: Determine the force in members BC, GA, and BG of the truss shown in the figure below. Let P = 175 kN...

A: Find the force in member BC,GA and BG

Q: ate is 30 kg/min. Determine a) the tons of refrigeration b) the power required c) the COP.

Q: An ideal Rankine cycle has a boiler pressure of 7.2 MPa and a condenser pressure of 0.45 MPa abs. St...

Q: 4- Single acting single cylinder compressor with diameter (15cm) and stroke length of (22.5cm).The a...

Q: (S) Sonic wave of air kg) "M2s 413 = Z (to a longer liquid KG (M3 950) and quickly sound) 's cm 7500...

A: Given Data,Zair=413 kg m2/sϕL=950 kgm2VL=750 m/s

Q: Using the method of joints, determine the force er of the truss shown. State whether each member r c...

Concept explainers

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.

Question

4.
The vehicle is designed to combine the feel of a
motorcycle with the comfort and safety of an automobile. If
the vehicle is traveling at a constant speed of 80 km/h along
a circular curved road of radius 100 m, determine the tilt
angle 0 of the vehicle so that only a normal force from the
seat acts on the driver. Neglect the size of the driver.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The sports car, having a mass of 1700 kg, travels horizontally along a 20° banked track which is circular and has a radius of curvature of p = 100 m. Determine the normal force of the car in Newton.
The 0.8-Mg car travels over the hill having the shape of a parabola. If the driver maintains a constant speed of 9 m/s, determine both the resultant normal force and the resultant frictional force that all the wheels of the car exert on the road at the instant it reaches point A. Neglect the size of the car.
Find the force F and P acting on the mass M (FBD massA,massB)
Combine the two forces P and T, which act on the fixed structure at B, into a single equivalent force R.
Ball D with a mass of 20 kg, if a force F = 10ON is applied to ring A in the horizontal direction, calculate the distance d so that the force on the AC rope is equal to zero.
combine the two forces P and T, which act on the fixed structure at B into a single force R
Determine the force P needed to cause the impending motion of the block
Find the force F on the bottom of the tank if : K=1.5 m , H= 6 m , D=5 m.
AB bar, negligible weightmovement on the surface indicated by the wheelsis doing. The bar is at rest when θ = 0°is being released. A and B when θ = 30°Find the velocities of the points.
A man pushes the lawn mower at a steady speed with aforce P that is parallel to the incline. The mass of themower with attached grass bag is 50 kg with mass centerat G. If  = 15°, determine the normal forces NB and NCunder each pair of wheels B and C. Neglect friction. (useg = 9.81 m/s2)
The 10-lb collar starts from rest at A and is lifted by applying a constant vertical force of F = 25 lb to the cord. Part A: If the rod is smooth, determine the power developed by the force at the instant θ = 60 degress
If F=1kN,the magnitude of the vertical reaction force developed at the point B?