Deturmine M- sy B- IN S = Im * (E). L2 - am • &N. filt) O (t) e0.1t 19 cos t+) -t+ ) 8/15 ¤ (t) : VIJ COS -0.1t -t 10 19

Q: In casting experiments performed during a certain alloy and type of sand mould it took 155 second fo...

A: A cube-shaped casting solidified in 155 seconds in a casting experiment using a specific alloy and k...

Q: Suppose you are taking a hike at Mt. Pulag with a terrain slope of 24° from the horizontal. After wa...

A:

Q: 3.61 A sign erected on uneven ground is guyed by cables EF and EG. If the force exerted by cable EF ...

A: Given: Force in the cable EF→FEF=46 lb We have to determine the moment about AD so we have to find o...

Q: Using the method of joints, determine the force er of the truss shown. State whether each member r c...

A:

Q: What is the difference between the friction of rest and the friction of motion, and which provides b...

A: The friction force is the resistance force, which acts in direction opposite to the motion of body. ...

Q: A composite wall is made up of external thickness of brick 110mm thick inside which is a layer of fi...

A: The thermal resistance of a plane wall can be calculated using the formula given below as- R=LkA whe...

Q: Water is flowing in a convergent duct. In one area, the diameter is 14 cm. If the velocity there is ...

A:

Q: 3. A cup of coffee that has been left on a table to cool to room temperature. Is the process reversi...

A: No this process is not reversible,because when coffee cooled down to room temperature the it will no...

Q: *Prob. 1.4-6. A portion of the boom of a crane at a construc- tion site is shown in Fig. P1.4-6. The...

A:

Q: metaicfhread: Pitch- 3mm thocadaryle=65 using 3-wire meltad Best size wisre diametoe ?

A:

Q: (i) List the name of the four processes in a generic Carnot cycle and state what type of energy tran...

A: Carnot cycle : A Carnot cycle is a theoretical perfect thermodynamic cycle suggested by Sadi Carnot,...

Q: Find vertical and horizontal reaction solid mechanics solve ??

A:

Q: (6) List the name of the four processes in a generic Carnot cycle and state what type of energy tran...

A:

Q: A medium size power station is used to produce 30 MW net power for a refinery. The station uses stea...

A: Given: The maximum pressure is Ph=35 bar and lower pressure is Pl=0.4 bar. The pressure correspond...

Q: at V = 2 m/s, T = 45°C, and atmospheric pressur over an isothermal plate at T, = 20°C. In the first ...

A: V=2m/sT∞=45°CTs=20°CRex,c=5×105x=0

Q: The space truss supports a force F = {600 i + 450j-750 k} lb. (Figure 1) %3D

A:

Q: A weight of 200lbs. rests on an inclined plane that makes an angle of 35° with the horizontal. If th...

A:

Q: 5. An electric water heater has a capacity of 2 liters. In this heater, the water is initially found...

A: given; initially volume(V1)=2 lt                           =2*10-3m3initially pressure(P1)=150KPa   ...

Q: The nozzle angle for an axial flow impulse turbine is 15°. The inlet absolute velocity is 800 ft./s ...

A: Given that, Nozzle angle for an axial flow impulse turbine, α=15°Inlet absolute velocity, V1=800 ft/...

Q: Three kg of steam at 121°C and 10%moisture undergoes a constant  volume process until the pressure ...

A:

Q: Q.4 Explain pressure feed lubrication system in I. C. engines

A:

Q: component of the hydrostatic force?

A: Given: Three cylindrical gates which restrain water in a 2D channel.Which gate experiences the maxim...

Q: Find the TOTAL DEDUCTION, round your answer. Gross pay: $399 O $30.5235 O $31 O $30.52 O None of the...

A: Given Gross salary = $399 To find Total deduction

Q: An actual steam power plant operates on a simple ideal Rankine cycle. The pressure in the boiler and...

A: Answer: The thermal efficiency of the actual steam power plant is 30.58568%.  

Q: show the step by step by constructing this using Solidworks. pls

A: Given 3D model To find Steps for modeling

Q: A solid cylinder of circular section of diameter d is of material with specific gravity S This float...

A:

Q: A cantilever beam carries a trapezoidal distributed load ( see figure) . Let wB=2.5 kN/ m, wA= 5.0kN...

A: The deflection and the angle of the free end of cantilever beam when subjected to uniformly distribu...

Q: 4.27 A reaction turbine produces 5600 hp while operating at 260 rpm and a head of 60 ft. It is propo...

A: CAVITATION: Cavitation is the arrangement and imploding of pits or air pockets in a fluid generally ...

Q: Refrigerant 134a undergoes a poly tropic process in a Piston- cylinder assembly from an initial stat...

A: Given data as per question Initial pressure =2 bar Final pressure =12 bar Find temperature =800c sta...

Q: Two steel pipes are used to support a 50KN load, as shown below. The pipes are connected to the wall...

A: Draw the FBD and find supports reactions

Q: Consider a steam power plant that operates on the ideal reheat Rankine cycle. Steam enters the high-...

A:

Q: Chnpter 2 Basic Knowledge of Orthogonal Projection 2 E n iR Draw the three views of the components o...

A:

Q: A flat rectangular plate 1 m wide and 2 m long is immersed in water. The shorter side parallel to wa...

A: Width of the flat rectangular plate, B= 1 m Length of the flat rectangular plate, L= 2 m With horizo...

Q: A mechanical system is depicted in the figure below. A pinion with fixed rotation axis passing throu...

A: Given : To find : Differential equation Transfer function

Q: Steam generators are a type of heat exchanges that are used in power plants to generate steam at des...

A:

Q: A medium size power station is used to produce 30 MW net power for a refinery. The station uses stea...

A: Given that, PH=35 bar,PL=0.4 bar, From the steam table, At P=35 bar,TH=242.5 °C,At P=0.4 bar,TL=75.8...

Q: A piston-cylinder device contains Is free to móve. The initial temperature and pressure of the Oxyge...

A:

Q: From the figure shown, the tube has an outer diameter of 80 mm and an inner diameter of 70 mm.  The ...

A:

Q: Shown below are three cylindrical gates which restrain water in a 2-D channel. Which gate experience...

A: Horizontal hydrostatic force = YAx' Where x' = c. G of body up to free surface             Y = weigh...

Q: The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and ...

A:

Q: Determine the maximum shearing stress in each springs supporting the rigid bar shown. Neglect the ma...

A: We have a rigid bar pivoted at an end and supported by two rigid springs, with a force of 5 KN actin...

Q: Problem 1. Beam AB has the given loading per unit length, q(x), Young's modulus, E, and a rectangula...

A:

Q: 2. Determine the force in each member of the truss shown. B 12' 9 E 9'- -9'- -9'- 300 lb 300 lb 900 ...

A:     From equilibrium conditions  

Q: A flat rectangular plate 1 m wide and 2 m iong is immersed in water. The shorter side parallel to wa...

A:

Q: 94 47 R5 212 35 Ø35 22 31 061 12 S6 22

A:

Q: 76. All surfaces of an infinitely long heating element, having a cross section in the shape of a cro...

A: Fins are the projection protruding from a hot surface into ambient air and they are meant for increa...

Q: 2. (20%) In the rotary system as below, where tire mass m, =12 kg, axle mass m, = 3 kg, and radius r...

A:

Q: For the structure shown in the figure, the working stresses are up to 16000 psi for the steel cable ...

A:

Q: The curve portion of a road is defined by y = 10 where x and y are in feet. Determine (a) the radius...

A: Given data curve of the road = y = x3106 speed of car when x = 600 ft =40 ft/s

Q: Determine the nodal displacements, the forces in each element, and the reactions. Use the direct sti...

A:

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.