APCB circuit using 2n3904 transistors is used to construct a Darlington-pair input circuit as shown below. Assume Br= 100. The Early voltage for the transistor is 75V. Determine the ECP circuit a) input resistance Select Rin MQ. b) Differential Voltage gain Select) * Avs ) Commom Mode Rejection Ratio Select in dB

APCB circuit using 2n3904 transistors is used to construct a Darlington-pair input circuit as shown below. Assume Br= 100. The Early voltage for the transistor is 75V. Determine the ECP circuit a) input resistance Select Rin MQ. b) Differential Voltage gain Select) * Avs ) Commom Mode Rejection Ratio Select in dB

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the NMOSFET in the circuit below, K = 4.00mA/V^2, VTHN = 1.00V, l = 0V^-1, and VIN = 4.00V.a. Draw the large signal model and small signal model of the circuit. b. Solve for IDS and VOUT and verify any assumptions you made. c. Derive an equation for the small signal gain of the circuit, vout / vin as a function of the vin radian frequency, w.
Consider the common-source amplifier shown in Figure P11.50. The NMOS transistor has KP=50 μA/V2, L=5 μm, W=500 μm, Vto=1 V and rd=∞.a. Determine the values of IDQ, VDSQ and gm. b. Compute the voltage gain, input resistance, and output resistance, assuming that the coupling capacitors are short circuits for the ac signal. Repeat Problem P11.50 for an NMOS transistor having KP=50 μA/V2, W=600 μm, L=20 μm, Vto=2 V and rd=∞. Compare the gain with that attained in Problem P11.50.
In the circuit given in the figure, Vcc = 15 V, R1 = R2 = 10kΩ, RE = 1KΩ, RL = 0.5kΩ and transistor parameters are given as VBE = 0.7V, ßdc = ß0 = 100. a. Calculate the values of DC bias currents and voltages (IBQ, ICQ and VCEQ). b. Draw the small signal equivalent circuit of the circuit using the hybrid model of the transistor. c. Derive the input impedance expression of the circuit and calculate its value. d. Derive the AVI and AVG voltage gain expressions and calculate their values. e. Derive the current gain expression AI = I0 / Ii and calculate its value. Compare this value you have calculated with the value you will calculate using the expression Aİ = Zi AVI / RL.
Answer as soon as possible. I'll upvote. Thank you. Using the given BJT small-signal model, determine the AC current gain Ai = iout/iin for the given circuit. Assume ro >> rπ. You may assume that β is large. (Hint: Draw the small signal circuit first before working on your analysis.)
The small-signal resistance (i.e., dv/dlp) in kn offered by the n-channel MOSFET M shown in the figure below, at a bias point of V 2V is. (Device data for M: device transconductance parameter, = KN = H₂Cox () = 40, threshold voltage VTN = 1V, and neglect body effect and Lambda)
Connect the elements given below as a BJT amplifier circuit with common emitter. BJT is BC547B terminals from left to right are named collector, base and emitter respectively. 9V battery as VCC source will be used. The audio signal obtained from the microphone will be connected to the circuit as the input signal. C0 at the outlet, CI at the inlet, CE is given as a bypass capacitor.
Connect the elements given below as a BJT amplifier circuit with common emitter. BJT is BC547Bterminals from left to right are named collector, base and emitter respectively. 9V battery as VCC sourcewill be used. The audio signal obtained from the microphone will be connected to the circuit as the input signal. C0 at the outlet, CI at the inlet,CE is given as a bypass capacitor.
(a) A current source with Rout = βoro is used to bias a standard bipolar differential amplifier. What is an expression for the CMRR of this amplifier for single-ended outputs?
discuss briefly a comparison of the three amplifiers (Common-Source, Source Follower, and Common-Gate) in terms of low-frequency gain and 3dB bandwidth (or half-power frequency).
The multistage amplifier circuit of Figure Q.2(b) have the following parameters:Q1 and Q2 : β = 200, VBE = 0.7 V, VT = 26 mV , VA = ∞Given that ICQ1 = 2 mA and VCEQ1 = 2 V. (i) Determine the value for RB4. List the assumption/approximation made in the analysis.(ii) Sketch and label the small-signal hybrid-π equivalent circuit at midbandfrequency range.(iii) Calculate the small signal hybrid-π model parameters: gm and rπ for Q1 and Q2. Then, determine Zi2 and Zo.
In the circuit given in the figure, Vcc = 15V, R1 = R2 = 10k ohm, RE = 1k ohm, RL = 0.5k ohm and transistor parameters are given as VBE = 0.7V, beta (dc) = beta (0) = 100. According to this;a) Calculate the values of DC bias currents and voltages (I (BQ), I (CQ), V (CEQ)).b) Using the hybrid model of the transistor, draw the small signal equivalent circuit of the circuit.c) Derive the input impedance expression of the circuit and calculate its value.d) Derive the voltage gain expressions A (vi) and A (VG) and calculate its value.e) Derive the current gain expression A (i) = I (0) / I (i) and calculate its value. I sent you question's image. Thank you..
The ac equivalent circuit for an amplifier is shown . Assume the capacitors have infinite value, RI = 750 Ω, RB = 100 kΩ, RC = 62 kΩ, and R3 = 100 kΩ. Calculate the voltage gain and input resistance for the amplifier if the BJT Q-point is (40μA, 10 V). Assume βo = 100 and VA = 75V.