As a design engineer, you are required to design a temperature detection system. The normal temperature for the system is 25 °C. There are three temperature sensors in the system. Each of the sensors will give a LOW input if normal temperature is detected and a HIGH input if a temperature higher than normal temperature is detected. The system will activate the red lamp when at least two temperature sensors detect a temperature which is higher than normal temperature. Meanwhile, the alarm will be activated when all the temperature sensors detect a temperature higher than normal temperature. Determine the logic circuit for the temperature detection system and write the corresponding Verilog coding using Dataflow Modelling. Show all the related steps.

As a design engineer, you are required to design a temperature detection system. The normal temperature for the system is 25 °C. There are three temperature sensors in the system. Each of the sensors will give a LOW input if normal temperature is detected and a HIGH input if a temperature higher than normal temperature is detected. The system will activate the red lamp when at least two temperature sensors detect a temperature which is higher than normal temperature. Meanwhile, the alarm will be activated when all the temperature sensors detect a temperature higher than normal temperature. Determine the logic circuit for the temperature detection system and write the corresponding Verilog coding using Dataflow Modelling. Show all the related steps.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter32: Two-speed, One-winding (consequent Pole) Motor Controllers

Section: Chapter Questions

Problem 6SQ: Describe the operation of Figure 325 (B) by adding jumper wire A to the original circuit.

See similar textbooks

Similar questions

An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
In the figure below Power Processor Input Output bag of Stop/Start Select one: a. O C. Motor O d. b. None of the choices e. Communication Power Input Output to ang On/Off control The presence of a processor module defines which rack is a local rack The yellow block represents a local rack Hopper The absence of a processor module defines which rack is a local rack The grey block represents a remote rack
Question 8 The average output voltage of full wave rectifier is more than half wave rectifier. True False Moving to another question will save this response. hp
What is the difference between AND and TEST instructions? A B I
6. Draw a comparator circuit to turn on an LED when the input voltage exceed 5 volts.
Identify the component which is not available in digital Voltmeter? a. Clock generator b. ADC c. Comparator d. 7-segment to BCD
Identify the followings H A Loja A B C E CR * D I Buzzer 2 g CR C B CR [Choose ] Holding contact Coil Start push button NC contact Float switch [Choose ]
AREF GND OREP 18 ESET 3.V GND GND Write a code to blink an LED connected to pin 3 five times with a delay of 500 ms each time using a for loop. There will be a pause of 3 seconds after each round .. DIGITAL (PWM - 0O UNO R ARDUINO ANALOG IN
A control input for an electronically controlled switch O is a terminal that is used for output acts like a resistor of electricity prevents or allows the flow of voltage based on the value of the control input O is a wire that always permits the flow of voltage
A circuit has two pushbutton switches connected to pin PB2and PB3 and two LEDs connected to pin PC0 and PC1 of AVR ATmega16 microcontroller. Write a program to control the LEDs as when any pushbutton pressedthe two LEDs will blink at the same time with 800ms total delay time for every blink.
19. Identify the response time of a meter. a. Time taken by output to reach final constant value from Zero value b. Time taken by output to reach 95% of value from 10% c. Time taken to settle inside 2% of the final value d. None of the options
What are the function of the following 8085 pins: INTR, RESET, HOLD, TRAP, ALE.