As an Electronic Engineer in XYZ Analog IC Design Centre, you are required to design Operational Amplifiers (Op-Amp). Based on combination of ideal Op-Amp as illustrated in Figure Q3 (b), derive the output voltages Vo1, Vo2, V03, and V04. If V₁ = 4 V and V2 = 2 V, determine V04. R Vio-W V₂0- 2R Voi R www R R www R 3R R www V03 V02 Figure Q3 (b) 2R www 4R 2R R V04

As an Electronic Engineer in XYZ Analog IC Design Centre, you are required to design Operational Amplifiers (Op-Amp). Based on combination of ideal Op-Amp as illustrated in Figure Q3 (b), derive the output voltages Vo1, Vo2, V03, and V04. If V₁ = 4 V and V2 = 2 V, determine V04. R Vio-W V₂0- 2R Voi R www R R www R 3R R www V03 V02 Figure Q3 (b) 2R www 4R 2R R V04

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Derive the appropriate equation for an inverting amplifier with op-amp and provide the values of resistances to obtain the gain equal 3 (kvR -> infinity, Vr -> 0)
The input-output relationship for the inverting op amp circuit is given ideally by: Vo = (-R f / Ri)Vi . The closed loop gain of the amplifier circuit is calculated as G = Vo/Vi. Use these equations to calculate the the expected output voltage and gain of the opamp circuit given
1. For n-stage analog amplifier circuit, if the voltage gain of each stage is Adi and the op amp common-mode rejection ratio is CMRRi (I =1~N): a) derive the mathematical expressions for the CMRR for the whole circuit b) analyze which stage’s CMRR has the most influence on the overall CMRR.
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem.
Graphically show the output voltage (Vo) and load current (IL) by simulating the difference receiving Op-Amp circuit given in the figure.(PSIM using PSpice or)R1 = R2=10kΩRL=1.5 kΩRf=14kΩ
Q3. For the op-amp circuit shown below, find the value of vO, where R1 = 20 Ω, R2 = 12 Ω, R3 = 15 Ω, R4 = 19 Ω, Rf = 17 Ω, VS1 = 12 V, and VS2 = 9 V.
Given circuit, assume op-amp is ideal. What is the input resistance of the circuit, RIN? What are the currents in the inputs of op-amp? i-=? i+=? What is the output resistance of the circuit, ROUT=? Find voltage VA and VB? What is the nodal equation (KCL) at node VB? Solve for VOUT=?
Assume that the op amp in the circuit shown is ideal. How large can Rx be before the amplifier saturates?
Using the components listed below, design an amplifier having a voltage gain of −10 ± 20 percent. The input impedance is required to be as large as possible (ideally, an open circuit). Remember to use practical resistance values. Cascade a non-inverting stage with an inverting stage.1) Standard 5%-tolerance resistors.2) Standard 1%-tolerance resistors. (Don’t use these if a 5%-tolerance resistor will do, because 1%-tolerance resistors are more expensive.)3) Ideal op-amps.4) Adjustable resistors (trimmers) having maximum values ranging from 100 Ω to 1 MΩ in a 1–2–5 sequence (i.e., 100Ω, 200Ω, 500Ω, 1 kΩ, etc.). Don’t use trimmers if fixed resistors will suffice.
ex: also could you help explain if consider this as an op-amp circuit, why the 1k ohms resistance belongs inside the amplifier but not Rin?
a) Design a non-inverting amplifier using an ideal op amp that has a gain 7.5.b) If you wish to amplify signals between -2V and 1.2V using the circuit you designed in part (a) what arethe smallest power supply voltages you can use?c) Draw your final circuit diagram.d) Assume that the voltage signal source is vs = −1V and the feedback resistor Rf is replaced with avariable resistor. Specify the range of Rf (in kΩ ) which will cause the op amp to saturate?