Answered: Q - The mechanism of bone as a solid…

Q - The mechanism of bone as a solid rod shown in figure. The diameter is 4 cm and it is subjected to the loading shown. Determine the normal stresses and shearing stress at point H shown at the rod.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.21P: An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec...

See similar textbooks

Related questions

Q: Find the stresses at points A andB on the plate shown in the figure.

A: The normal stress at the points A and B can be determined as,

Q: At a point in a stressed body, the cartesian components of stress are Oxx = 60 MPa, Guy = -40 MPa,…

A: Given Data σxx=60 Mpa σyy=-40 Mpa σzz=20 Mpa τxy=-40 MPa τyz=20 MPa τxz=30 MPa Stress tensor,…

Q: A steel pipe assembly supports aconcentrated load of (P = 22 kN) as shown in Figure. The outside…

A: Calculate the moment about point H due to load P. MH=P370 mm×1 m1000 mm=22 kN×1000 N1 kN370 mm×1…

Q: A solid disc rotating with maximum velocity V and having Poisson's ratio is u, then the maximum…

A: A solid disc rotating with maximum velocity v,then maximum tangential , radial stress develops(c) At…

Q: Rod AB is fixed at side A with a length of 500m and a diameter of 20m. On side B, the rod…

Q: At a point in a stressed body, the principal stresses are oriented as shown in the figure. Use…

Q: A same circular plate with radius of Ro-560mm and thickness of h=7.42mm is considered here again.…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 3700 psi, Sy =…

A: Find angle with vertical to find the normal and shear stress at the given plane, θ= 90 - β= 90-49=…

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: The state of plane stress at a point is represented on the element shown in the figure below. (a)…

Q: 2. A plane element in a body is subjected to a compressive stress of 80 MPa accompanied by a shear…

Q: Using the Mohr circle or analytical solution for the plane stress case in the figure; (a) Principal…

Q: In the figure shown, determine the normal stresses at AD and BC shearing stress at bolt D bearing…

A: Given data, Diameter of the bolt, d = 16 mm Free body diagram of EDC where, RD and RC are the…

Q: The state of plane stress at a point is shown on the element in Figure below. Represent this state…

A: Given: The orientation of element, θ = 45° The stress along x-axis, σx = -10 ksi The stress along…

Q: Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as…

A: Given, Force, F=178NInside diameter, di=2.66cmOutside diameter,do=3.34cm Moment of Inertia,…

Q: 4. The state of stress at a point, for a body in plane stress, is shown in the figure below. If the…

Q: (Q2: if a point is subjected to the state of stress shown in figure determined the principles stress…

Q: rect stresses of 160N/mm tensile and 120 N/mm compressive exist on two perpendicular planes at a…

A: Given, direct tensile stress, σt=160N/mm2 Compressive stress, σc=120N/mm2 The greatest principal…

Q: A same circular plate with radius of Ro-560mm and thickness of h=7.42mm is considered here again.…

Q: A circular rod of a diameter of 100 mm is subjected at its free end to force F1 = 50N and F2=(200j -…

A: In this question, three forces are given. The forces are Point force, F1=50i kN Point force,…

Q: Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as…

A: Given Data Force applied on the wrench and the force transferred to the end of the pipe, F=178 N…

Q: Find the stresses at points A and B on the plate shown in the figure.

A: The normal stress on the point A can be determined as,

Q: In the figure shown, determine the normal stresses at AD and BC shearing stress at bolt D + ,…

A: Given, tEDC = 10 mmwEDC = 50 mmtAD = tBC = 8 mmwAD= wBC = 36 mmd = 16 mmF = 20 kNLAD = LBC = 0.2 m…

Q: Determine the equivalent stress state of an element oriented 30° clockwise with respect to the…

Q: In the figure shown, determine the normal stresses at AD • , shearing stress at + and BC bolt D • ,…

A: Solution: The free body diagram of the EDC is shown above, we need to find the reactions RD and RC…

Q: A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure. Determine…

Q: Oy Ot Txy a Tnt Ox On (b) (a) On the surface of a structural member, stresses are given as ox=67,9…

A: Given data: The stress in x-direction is σx=67.9 MPa The stress in y-direction is σy=25.5 MPa The…

Q: The state plane stress at a point is represented by the stress element below. Determine the stresses…

Q: 934. If an element is subjected to the state of stress shown in Fig. P-934, find the principal…

Q: 4. For an element subjected to stresses of x= 70 ksi y=-15 ksi xy=30 ksi SAH: (a) Draw Mohr's…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Loads acting on a body induces stresses in all directions at any point of the body. The point can be…

Q: The greatest normal stress, b) The greatest shear stress, c) Calculate the shear stress at point a.

A: GIVEN :-Squre hollow bar : h=100mmlength : L=1100mmthickness: t=10 mm SOLUTION :- using force…

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure. Determine…

Q: Q5: At a point in a strained material the stresses acting on planes at right angles to each other…

Q: Q#4: Considering the original state of stress as shown in figure below and recalling the already…

A: The equation for the normal stress at an angle θ from the x-axis is given by,…

Q: Determine the principle stresses and the maximum in-plane shear stress.

Q: 3. At the point labeled A in the bracket below, the stresses are og = 4.8 ksi, o, = -1.2 ksi and Ty…

Q: For the state of plane stress, stress components are shown on the element in Figure Question 1: a)…

Q: An element in plane stress is subjected to stresses o, = -60 MPa, oy = -40MPA, and Ty = 35MPA, as…

Q: Plane Stress In the stress element given in Figure, WITH MOHR CIRCLE; a- Determine the principal…

A: To Find 1.MOHR CIRCLE 2.the principal stress directions by calculating the principal stress values…

Q: The hollow cylinder is fixed at the wall and pressurized at p = 2,000 Pa. Its outer diameter (OD)…

Q: Determine the normal and shear stresses at point D that act perpendicular and parallel,…

A: Given: The load at the point D is 10 kN. The beam is shown below:

Q: Calculate the principal stresses and angles and in-plane maximum shear stresses and angles for t…

A: Given Data⇒ σx=20 MPaσy=30 MPaζxy=60 MPa

Q: MECHANICS OF DEFORMABLE BODIES The butt joint shown in the figure is connected using five 20mm…

Q: P, P. P,

A: given:

Q: Please answer attach file

A: Given dataStress in x direction σx = -27MPaStress in y direction σy = 5.5MPaShear stress ζ =…

Q: state of the stress is illustrated in the figure below. For the given plane stress condition…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Q - The mechanism of bone as a solid
rod shown in figure. The diameter is 4
cm and it is subjected to the loading
shown. Determine the normal stresses
and shearing stress at point H shown at
the rod.
250 mm
-H-
150 N
150 mm
4 cm
300 N
200 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
• - 7.4-7 An element on the surface of a drive shaft is in pure shear and is subjected to stresses ??xy= 2700 psi, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an element oriented at a counterclockwise angle ?= 52° from the y axis. (b) The principal stresses. Show all results on sketches of properly oriented elements.
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
1 A rectangular steel plate with thickness t = 5/8 in. is subjected to uniform normal stresses a and ., as shown in the figure. Strain gages A and B. oriented in the x and v directions. respectively, arc attached to the plate. The gage readings give normal strains = 0.00065 (elongation) and £. = 0.00040 (elongation). Knowing that E = 30 X 106 psi and v = 0.3, determine the stresses c7 and a, and the change .11 in the thickness of the plate.
-18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-18 sx= 2900 kPa, sy= 9100 kPar,txy=-3750kPa
.4-2 An element in uniaxial stress is subjected to tensile stresses sx= 57 MPa. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at an angle 0 = 33° from the x axis (minus means clockwise). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.