As shown in the figure, a rigid beam with negligible weight is pinned at one end and attached to two vertical rods. The beam was initially horizontal before the load W = 200KN was applied. Find the vertical movement of W. Given: Reqd: Bronze A = 900 sq.mm E =120 GPa 1.5m B L = 1.2m 3.0 m Vertical movement of W W Steel A = 500 sq.mm E = 200 GPa L= 4m 2012. W = 200 KN final position Meeting in CE397 R2

As shown in the figure, a rigid beam with negligible weight is pinned at one end and attached to two vertical rods. The beam was initially horizontal before the load W = 200KN was applied. Find the vertical movement of W. Given: Reqd: Bronze A = 900 sq.mm E =120 GPa 1.5m B L = 1.2m 3.0 m Vertical movement of W W Steel A = 500 sq.mm E = 200 GPa L= 4m 2012. W = 200 KN final position Meeting in CE397 R2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use THREE MOMENT EQUATION MET determine the member end moments of the beam of the rectangular cross section shown in Figure 11.10a. Assume that support B settles 2 cm. The modulus of elasticity and the moment of inertia of the beam are E = 210,000 N/mm2 and 4.8 × 104 mm,4 respectively. Hint final answer: MAB= 0 MBA= 165.5127 kn.m MBC= -165.5127 kn.m MCB= 52.2604 kn.m
Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️
As shown in the figure below, a cantilever beam has a span of 6m long. And it is subjected to a concentrated load 6kN acting 4m from the support and a clockwise moment of 30kN.m at the free end. E = 200 GPa and I = 100,000,000 ??^4 . (Use area moment method) a) Determine the deflection at the free end due to concentrated load only. b) Determine the maximum deflection at the free end.
5. Given: XW = 48.85 ft and weight of W = 652 lb, ? = 36° Solve for the tension in XW connected to W in lb at Y, wherein velocity of W = 14.8 ft/s Report your answers in 3 significant digits
Use Moment Distribution Method determine the member end moments of the beam of the rectangular cross section shown in Figure 11.10a. Assume that support B settles 2 cm. The modulus of elasticity and the moment of inertia of the beam are E = 210,000 N/mm2 and 4.8 × 104 mm,4 respectively. Hint final answer: MAB= 0 MBA= 141.9 kn.m MBC= -141.9 kn.m MCB= 81.26 kn.m
Situation 5. The column is used to support the floor which exerts a force of 3000 lb on the top of the column. The effect of soil pressure along its side is distributed as shown. 10. Replace this loading by an equivalent resultant force in lb. a. 3253.9 b. 4260.0 c. 3003.3 d. 3918.0 11. Specify where it acts along the column, measured from its base A in ft. a. 3.86 b. 1.62 c. 5.14 d. 1.4
A wooden beam ( sg= 0.64) is 150 mm by 150 mm by 6m and is hinged at A as shown in the figure. Assuming unit weight of water is 9.79 kN/cu.m. a.) Determine the length of the beam submerged in water? b.) At what angle will the beam float in the water? c.) And determine the buoyant force that causes the beam to be submerged at an angle of theta from horizontal. Please answer this correctly PLEASE :(
calculate the Axial Force in kips on member BC if the given 30kip and 20kip loads from the figure are both replaced by 42kips and 45kips respectively. Express your answer in 2 decimal places. Include (-) negative sign if the axial force is compression.
Only accepted correct answer is 2.84. Please show solution. A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area.
Determine the resultant of the vertical thrusts on the sphere shown in the figure for the data: d=0.6m; R=0.5m;h=4m.
If beam as shown in Figure has a rectangular section with a depth of 100mm and width of 20mm, calculate the slope and deflection at free end. Assume E = 200GPa.where P=55
Given a cantilever beam of length L=2.8meters. The left support “A” is free while the right end “B” is fixed. With constant EI=19000 KN-m2 A downward concentrated load of 54KN is applied at “A”. Using Double Integration Method (DIM) with origin taken at point A where 0 ≤ x ≤ L, calculate the first constant of integration, C1? Express your answer in KN-m2 in 2 decimal places.