Step by step solution please thank youuu. Finding mass flow rate, volumetric flow rate and velocity. As shown in the figure, air with a volumetric flow rate of 17,000 ft°/min enters an air-handling unit at 80°F, 1 atm. The air-handlingunit delivers air at 45°F, 1 atm to a duct system with three branches consisting of two 26-in.-diameter ducts and one 50-in. duct. Thevelocity in each 26-in. duct is 13 ft/s. Assume steady state operation and ideal gas behavior for the air.4+D - 50 in.DuctTz = T3 = T, = 45°FD; = D, = 26 in.V2 = V3systemAir-handling unit1+ P = P2 = P3 = P4 = 1 atmT = B0°F(AV),Determine the mass flow rate of air entering the air-handling unit, in Ib/s, the volumetric flow rate in each 26-in. duct, in ft/min, andthe velocity in the 50-in. duct, in ft/s.

Answered: Image /qna-images/answer/e4fb7df5-df17-415b-aed1-91464392ec50.jpg

Answered: As shown in the figure, air with a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assuming the clearance is negligible for a single stage compressor with the following data : Atmospheric pressure = 90 kPa, Atmospheric temperature = 17 degrees, Delivery pressure = 7 bar, Free air delivery flow rate = 0,2 m³/min. Take n= 1,3, Cp=1,005 KJ/Kg K, Cv=0,718 KJ/Kg K Determine the following : A) Which formula is used to evaluate the delivery temperature for an isentropic? B) the delivery temperature of air for a polytropic compression process with n=1,25 in Kelvin to 1 decimal place? C) the mass flow rate of air inside the compressor operating isentropically in kg/min to 3 decimal places? D) the power input to the compressor in kW to 2 decimal places if the compression is polytropic compression process with n=1,25? E) the power input to the compressor in kW to 3 decimal places if the compression reversible isothermal? F) the power input to the compressor if the compression is isentropic in kW to 3 decimal places? G) the delivery temperature of air for an isentropic…
Steam at 80 bar, 440 °C, enters aturbine operating at steady state with avolumetric flow rate of 236 m 3 /min.Twenty percent of the entering massflow exits through a diameter of 0.25m at 60 bar, 400 °C. The rest exitsthrough a diameter of 1.5 m with apressure of 0.7 bar and a quality of 90%. Determine the velocity at each exitduct, in m/s.
5Air enters a two-stage compressor operating at steady state at 520°R, 14 lbf/in.2 The overall pressure ratio across the stages is 12 and each stage operates isentropically. Intercooling occurs at constant pressure at the value that minimizes compressor work input, with air exiting the intercooler at 520°R. When the temperature of the air entering each compressor stage is the same, the minimum total compressor work input per unit of mass flowing occurs when the pressure ratio is the same across each stage.Assuming ideal gas behavior, with k = 1.4, determine the work per unit mass of air flowing for the two-stage compressor, in Btu per lb of air flowing.
State 1 for a dual combustion engine is p1 = 1 atm and T1 = 60.3 degrees Celcius; rk = 18; at the end of the constant volume combusion process the pressure is 7695 kPa, Re = 1.5 Base on 1 kg/cycle of a hot-air standard with k = 1.31, determine a) the percentage clearance, b) p, V and T at each corner point on the cycle c) W, d) e and e) Pm
The following data were obtained from a performance test of a 10 x 9-cm single acting, water jacketed two-stage air compressor: Pressures: Atmospheric, 102 kPaa; leaving first-stage, 634 kPaa; leaving second-stage, 4.20 MPa. Temperatures: Atmospheric, 240C; leaving first-stage, 1080C; entering 2nd stage, 250C; leaving 2nd stage, 1270C Compressor speed, 648 rpm Power input to motor, 5.65 kW Motor and belt efficiency, 81.5% The following are calculated from test data: Air flow rate, 0.387 ??⁄??? Compression exponents: 1st stage 1.15; 2nd Stage, 1.2 Calculate: a) Approximate indicated power b) Power for isothermal compression c) Shaft power d) 1st stage piston displacement e) Actual volumetric efficiency f) Isothermal compression efficiency g) Mechanical efficiency based on the approximate indicated power h) Over-all efficiency of the compressor
Air enters a two-stage compressor operating at steady state at 520°R, 14 lbf/in.2 The overall pressure ratio across the stages is 20 and each stage operates isentropically. Intercooling occurs at constant pressure at the value that minimizes compressor work input, with air exiting the intercooler at 520°R. When the temperature of the air entering each compressor stage is the same, the minimum total compressor work input per unit of mass flowing occurs when the pressure ratio is the same across each stage.Assuming ideal gas behavior, with k = 1.4, determine the work per unit mass of air flowing for the two-stage compressor, in Btu per lb of air flowing.
8Air enters the diffuser of a ramjet engine (schematic shown below) at 6 lbf/in.2, 420°R, with a velocity of 1800 ft/s, and decelerates essentially to zero velocity. After combustion, the gases reach a temperature of 2000°R before being discharged through the nozzle at 6 lbf/in.2 On the basis of an air-standard analysis, determine:(a) the pressure at the diffuser exit, in lbf/in.2(b) the velocity at the nozzle exit, in ft/s.Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Assume combustion occurs at constant pressure and flow through the diffuser and nozzle is isentropic.
The following data are known for Libr-H₂O absorption system. The cooling capacity is 3.5 kW, generation temp. is 82°C, condenser temp. 40°C, evaporator temp. 6°C. Temp. of absorber is 34°C. Assumed saturation condition for strong solution entering generation, weak solution leaving generation and water vapor Leaving evaporator. Properties of solution or water at each point (p, t, h, x), Mass flow rate each point,(COP) act & (COP) tho, Relative COP and Energy balance for all cycle components.
Steam at 44 bar and a dryness fraction, x = 0.9 is throttled to a pressure of 12 bar. Calculate thedifference in power output in kilowatts between the following two expansion processes:a) Steam at the initial pressure of 44 bar and x = 0.9 at State 1 is expanded in a turbine to State 3 at 0.12 bar.b) Steam at the reduced pressure of 12 bar after throttling at State 2 is expanded in another turbine to State 4 at the same exhaust pressure of 0.12 bar.The mass flow rate of steam is 8 kg/sec in both cases and the expansion in both turbines can be assumed to be reversible and adiabatic. Sketch both expansion processes on the same T-s diagram using the respective initial and final state points as described above.Explain the reason for the difference in power output.Calculate the mass flow rate of steam for the turbine operating at the throttled/reduced pressure to generate the same output as the turbine operating at the pressure before throttling.NOTE: You are required to number the state…
OTTO CYCLE At the start of an air-standard Otto cycle's compression process, P1 = 1 bar, T1 = 300 K, V1 = 380cm3. The maximum temperature in the cycle is 2400 K and the compression ratio is 9. Determine the: (d) the mean effective pressure, in bar. Show complete solution.
1000 cfm of air at 95°F dry bulb, 74°F wet bulb is mixed with 2000 cfm of air at 65°F dry bulb, 54°F wet bulb. Determine the volumetric flow rate of the mixed stream.A. 1845 cfmB. 2445 cfmC. 2745 cfmD. 3104 cfm
The O2 input conditions to a nozzle, which operates in steady state, are 60 bar, 300 K and 1 m/s. The gas expands isentropically at 30 bar. Determine the output speed in m/s. Assume that oxygen is described by the Peng-Robinson equation

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS