As shown in the figure, block D is used to support the 100-kg uniform pole ABC in the position shown. 1) Find the normal force at point B. 2) Find the frictional force at point B. 3) Calculate the weight of the lightest block D that can be used to support the pole against impending sliding. 4) Calculate the weight of the lightest block D that can be used to support the pole against

As shown in the figure, block D is used to support the 100-kg uniform pole ABC in the position shown. 1) Find the normal force at point B. 2) Find the frictional force at point B. 3) Calculate the weight of the lightest block D that can be used to support the pole against impending sliding. 4) Calculate the weight of the lightest block D that can be used to support the pole against

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter5: Newton's Law Of Motion

Section: Chapter Questions

Problem 85AP: Two boxes, A and B, are at rest Box A is on level ground, while box B rests on an inclined plane...

See similar textbooks

Similar questions

One or more external forces are exerted on each object enclosed in a dashed box shown in Figure 4.2. Identify the reaction to each of these forces.
If an object is to rest o an incline without slipping, then friction must equal the component of the weight of the object parallel to the incline. This requires greater and greater friction for steeper slopes. Show that the maximum angle of an incline above the horizontal for which an object will not slide down is =tan1s . You may use the result of the previous problem. Assume that a=0and that static friction has reached its maximum value.
If you used an ideal pulley of the type shown in Figure 9.26(a) to support a car engine of mass 115 kg, (a) What would be the tension in the rope? (b) What force must the ceiling supply, assuming you pull straight down on the rope? Neglect the pulley system's mass.
A team of eight dogs pulls a sled with waxed wood runners on wet snow (mush!). The dogs have average masses of 19.0 kg, and the loaded sled with its rider has a mass of 210 kg. (a) Calculate the acceleration of the dogs starting from rest If each dog exerts an average force of 185 N backward on the snow. (b) Calculate the force in the coupling between the dogs and the sled.
Athletes such as swimmers and bicyclists wear body suits in competition. Formulate a list of pros and cons of such suits.
Construct Your Own Problem Consider the tension in an elevator cable during the time the elevator starts from rest and accelerates its load upward to some cruising velocity. Taking the elevator and its load to be the system of interest, draw a free-body diagram. Then calculate the tension in the cable. Among the things to consider are the mass of the elevator and its load, the final velocity, and the time taken to reach that velocity.
A 78 kg man is being hauled away from a flaming building as shown in the figure. Calculate the tension T1 on the left side of the rope and T, in newtons, if the man is in static equilibrium.
A plank is supported by 120N forces at A and B, as shown. The supportat A is then repositioned to C which is halfway to the center. The normal force at B and C are ____ and _____ respectively. Choices: 200 N, 40N 160 N, 80N 80N, 160N 40N, 200N 240 N,120N Show complete solution and free body diagram
The figure below shows a bird feeder that weighs 100.1 N. The feeder is supported by a vertical wire, which is in turn tied to two wires, each of which is attached to a horizontal support. The left wire makes a 60° angle with the support, while the right wire makes a 30° angle. What is the tension in each wire (in N)
Suppose a horse leans against a wall as shown in the figure. The total mass of the horse and rider is 515 kg. Calculate the force, in newtons, exerted on the wall, assuming that force is horizontal and using the data in the schematic representation of the situation. Fwall =
An 80-kg construction worker sits down 2.0 m from the end of a 1450-kg steel beam to eat his lunch. Draw a free-body diagram and use it to calculate the tension, T, in the cable supporting the beam. If the cable is rated at 15,000N, should the construction worker be worried? Bonus: Where should the construction worker sit on the beam so that the tension is exactly 15,000N?
The simply supported beam in Figure Q3a has four concentrated loads acting at points C, D, E & F. There is also a uniformly distributed load (UDL) of 20 N/m between D and E. Calculate the reaction forces RA and RB at support A and support B respectively. *Assume that the weight of the beam is zero.