Assume a Centaur V upper stage with an empty mass of 2,247 kg, diameter of 3.05 metersand height of 12.68m, the wall thickness is 41mm, whereas the motor can be assumed tofill up 1/4 of the inner volume. You can assume the density of the walls and the motor tobe uniform. You can assume the upper stage has been properly passivated and has no fuelremaining. 1. Taking the Centaur upper stage from last week and assume it is spin stabalized. Model a realnutation damper. You can neglect the gravity gradient torque.(a) Plot the attitude of the upper stage, starting with an intial angular velocity of 80rpmalong the spin axis of the cylinder and 2rpm in the remaining directions. Code up inmatlab, include all matlab code in your submission, and write out relevant equationsand where you use them in your code by hand. Comment on your plots and the resultsthat you observe. Use for the nutation damper values α = 0.75, p = 0: 003.

Part 1: Calculation of Moment of Inertia The moment of inertia of the Centaur V upper stage can be…

Assume a Centaur V upper stage with an empty mass of 2,247 kg, diameter of 3.05 meters and height of 12.68m, the wall thickness is 41mm, whereas the motor can be assumed to fill up 1/4 of the inner volume. You can assume the density of the walls and the motor to be uniform. You can assume the upper stage has been properly passivated and has no fuel remaining.

Assume a Centaur V upper stage with an empty mass of 2,247 kg, diameter of 3.05 meters and height of 12.68m, the wall thickness is 41mm, whereas the motor can be assumed to fill up 1/4 of the inner volume. You can assume the density of the walls and the motor to be uniform. You can assume the upper stage has been properly passivated and has no fuel remaining.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a rocket nozzle, knowing that you have a chamber pressure of 6.28 MPa, mass flow rate of 1.23, and temperature of 825K.
Vacumm You are designing a vacuum system with a desired equilibrium pressure of 10-7 torr. The turbomolecular pump you are using has a pumping speed of 400 L/s. What is the maximium surface area of the chamber that you can allow, assuming that the outgassing rate per square cm 10-9 torr L/s? Note : total outgassing rate G = ( outgassing rate per area ) * ( area )
explanation of the performance tests undertaken for a wind turbine. With the options found, give a justified recommendation for the best system.
In order to predict the behavior of a small oil pump, tests are to be made on a model using air. The oil pump is to be driven by a 1/20 hp motor at 1800 rpm and a ¼ hp motor is available to drive the air pump at 600 rpm. Using the SG of oil at 0.92 and the density of air constant at 0.00238 slug/ft3, what size model should be built?
A pump has a displacement of 90 cm3 . It delivers 75 Lpm at 1300 rpm and 75 bar .If the prime mover torque is 90 N-m. What is the theoritical troque required to operate the pump? a. 107.48 N-m b. 75 N-m c. 120.54 N-m d. 90 N-m
A propeller type, horizontal axis wind turbine having following windcharacteristics: Speed of the wind 10 m/s at 150 C, The turbine has diameterof 120 m and its operating speed is 40 rpm at maximum efficiency.Calculate (i) the total power density in the wind stream (ii) the maximumobtainable power density assuming wind power coefficient as 40% (iii)total power produced in kW (iv) Maximum thrust and axial thrust.[Ans: 613 W/m2 , 2771 kW, 6930 kW, 619.9510 kN, 897 kN]
A drum type steam generator operates at (160 bar). (1260 kg/s) of saturated water goes down the downcomer. The downcomer and risers are all (12 m) high. The average water‐ steam mixture density in the risers is (350 kg/m3 ). Calculate the power, in kilowatts, needed to drive a forced circulation pump if the pump efficiency is (70%).
Pumps: A centrifugal pump having 4 stages in parallel, delivers 18 kiloliters/min of liquid against a head of 25 m. The diameter of the impellers being 24 cm and the speed of 1800 rpm. A pump is to be made up with a number of stages in series of similar construction to that of the first pump to run at 1250 rpm and to deliver 15 kiloliters/min against a totalhead of 250 m. Find the diameter of the impellers and the number of stages required in this case. Answer: D = 46.63 cm, n = 6 stages
Question. A boiler unit has forced draught fan maintaining draught of 90 mm of water column while discharging 38 m/s through outlet section of 1.9m² area. Ambient temperature is 300 K and assume mass of 1 m³ of air at NTP as 1.293 kg to find out power of motor of forced draught fan if for efficiency is 80%. Determine the power consumption if FD fan is substituted by ID fan of similar efficiency considering flue gas temperature of 450 K
In a Parson reaction turbine, the angles of receiving tips are 35º and of discharging tips 20º.The blade speed is 125 m/s. Calculate the tangential force, power developed, diagramefficiency and axial thrust of the turbine, if it steam consumption is 1.5 kg/min.
The pressure ratio during the constant volume portion of combustion in a Dual Combustion engine is 1.89 . If the pressure at the end of the constant volume addition of heat is 4.49 , what is the pressure at the beginning?
a. Given the static head of 28.91 m, and static pressure head of 3.15 cm WC. What is the normal pressure, Pn? b. What is the Static efficiency of the fan if the air flow rate is equal to 3.8 5m /sec, total head of 68.72 m, velocity head of 30.86 m, mechanical efficiency and power are 39.12% and 35.72 KW at 30.69°C, respectively. c. Solve for the area at entrance of the fan blade, if the it has a 346mm diameter, flow of air is equal to 23.328 m/se and flow rate of 3.05 m³ /second.