Q1. A typical graph of strain (e) versus time for a metal under creep conditions is shown below. င် B A C D E time Please select the correct labels from the graph above that correspond to the phases of a creep curve given to you for input values for Q1. (i) and Q1. (ii) and write your answers in the table on the cover sheet for [Q1. (i) and (ii)]. Note: your answers should state the letter that corresponds to the appropriate region described by the terms you were given, e.g. A, B, etc.

Q1. A typical graph of strain (e) versus time for a metal under creep conditions is shown below. င် B A C D E time Please select the correct labels from the graph above that correspond to the phases of a creep curve given to you for input values for Q1. (i) and Q1. (ii) and write your answers in the table on the cover sheet for [Q1. (i) and (ii)]. Note: your answers should state the letter that corresponds to the appropriate region described by the terms you were given, e.g. A, B, etc.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How are you getting 16 mm at the end for an answer , "HX83=219X10^3/164.909".................is that your diving by f/a and multiplying by 83 to get H , im just no sure what you did to get 16 ?.
Thermal efficiency of a power cycle is 0.8. For the cycle, Wnet = 250 kJ. Determine Qout in kJ. Enter the answer without units and without rounding.
#01: Explain the following terms in your own words. a) Aerodynamics. b) Mach Number. c) Sub-Sonic. d) Angle of Attack. e) Thrust. f) Chord Line. g) Drag Coefficient. h) Pitch Moment. i) Wind Tunnel. j) Skin Drag.
The horizontal force due to water acting on the bolt (Fh): Fh=ρ×A1×V1×V1--V2 Fh=1000×π4×0.0752×1.254×1.254+11.286( Fh)=69.472 This is the only part I did not understand how to get. Can you please explain more? I arrived with this equation, -P1A1 - P2A2 (cancelled since atmos. Pres.) +Fh = rho A1v1 (v2-v1) Why did P1A1 disappear in your solution? How did you come up with (v1 - - v2) ? What is the control volume? Why did you not do a summation of forces is equal to change in momentum but instead go immediately to getting the horizontal force acting on the bolt?
Show complete solution and 3 decimal places for the final answer. Asap thanks! A truck carrying fully-filled water container that is 2.5m long, 2.5m wide, and 2m high. The entire mass is 3000kg encountered an unbalanced force of 15kN. Estimate the acceleration in m/s^2.
Solve all the five questions, then show your complete solutions! Given: FN = 52 MN = 100 SN = 75
Study the table to the right and then answer these questions by filling in the blank columns in the table.1. Convert the miles per gallon figures in the table tokilometers per liter (kpl).2. How many liters (and how many gallons) of gasolinewould each type of car use annually if it were driven19,300 kilometers (12,000 miles) per year?3. How many kilograms (and how many pounds) of carbon dioxide would be released into the atmosphereannually by each car, based on the fuel consumptioncalculated in question 2? Assume that the combustion of gasoline releases 2.3 kilograms of CO2 per liter(19 pounds per gallon).
1. Energy consumption in a country from 2001 to 2011 increased from 1041.3 million to 1526.1 million BOE (barrels of oil equivalent). If the high calorific value (HHV) of the oil is 141,000 kJ/gallon what is the increase in energy consumption over 10 years in Joule units. What is the rate of energy consumption per year? 2. Based on data on the rate of energy consumption per year from question no. 1, if the growth rate energy 2.5% per year, calculate the doubling time (td) and what is the approximate rate of energy growth in 2021.
THE FINAL ANSWER SHOULD BE 10.75 m^3/s. Include cancellation of units and solve completely
given:Q2A=12 INCHESAB= 2FT 4 INCHESBC= 8 INCHESDE = 1 FT 3 INCHESQ7E= 12 INCHESQ5C= 2 FTDF= 2 FTCE = 3FT Ks -> use appropriate scaleKv -> 400ft/min= 1 inchVa= 472 ft/ min ☆ Solve the velocities of F and E by Resolution and Composition☆ pls show the output
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s. In the design specifications given, if the actual measurement of power via the substation amounts to exactly 530kW and given that the windspeed is off by 0.05m/s, what could have been the error in the measurement of diameter? Your answer must be in 3 decimal places and in correct signs and measurement. Show complete solution in paper.
In a hypothetical diesel engine the fuel is compressed from 579mL to 32.9 mL. This rasies the temperature of the fuel form 25°C to its ignition temperature of 210°C. If the fuel begins at 1.00atm, what is the pressure of the fuel at its ignition temperature.? Express your answer to 1 decimal place