1. Assume a Centaur V upper stage with an empty mass of 2,247 kg, diameter of 3.05 metersand height of 12.68m, the wall thickness is 41mm, whereas the motor can be assumed tofill up 1/4 of the inner volume. You can assume the density of the walls and the motor tobe uniform. You can assume the upper stage has been properly passivated and has no fuelremaining. (b) Code in matlab the translational motion via numeric integration of the orbit (two-bodyorbit sufficient). Use the orbital characteristics of the Centaur V upper stage from theAtlas V launch on August 21, 2002 with the COSPAR ID 2002-038-B. You can look upthe most recent orbital elements online (heavens-above.com).¹ Make a 3D plot of thepropagation over one orbital period.

The orbital elements for the Centaur V upper stage from the Atlas V launch on August 21, 2002 with…

Assume a Centaur V upper stage with an empty mass of 2,247 kg, diameter of 3.05 meters and height of 12.68m, the wall thickness is 41mm, whereas the motor can be assumed to fill up 1/4 of the inner volume. You can assume the density of the walls and the motor to be uniform. You can assume the upper stage has been properly passivated and has no fuel remaining.

Assume a Centaur V upper stage with an empty mass of 2,247 kg, diameter of 3.05 meters and height of 12.68m, the wall thickness is 41mm, whereas the motor can be assumed to fill up 1/4 of the inner volume. You can assume the density of the walls and the motor to be uniform. You can assume the upper stage has been properly passivated and has no fuel remaining.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

explanation of the performance tests undertaken for a wind turbine. With the options found, give a justified recommendation for the best system.
Each of the four jet engines on an Airbus A380 airliner develops a thrust (a forward force on the airliner) of 322,000 N. When the airplane is ﬂying at 250 m/s, what horsepower does each engine develop?
Design a rocket nozzle, knowing that you have a chamber pressure of 6.28 MPa, mass flow rate of 1.23, and temperature of 825K.
Vacumm You are designing a vacuum system with a desired equilibrium pressure of 10-7 torr. The turbomolecular pump you are using has a pumping speed of 400 L/s. What is the maximium surface area of the chamber that you can allow, assuming that the outgassing rate per square cm 10-9 torr L/s? Note : total outgassing rate G = ( outgassing rate per area ) * ( area )
A two stage compressor with first stage piston displacement of 94,390 cu.m/sec is driven by a motor. Motor output is 35 HP, suction temperature 22 degC, volumetric efficiency is 85%, mechanical efficiency is 95%, the intercooler pressure is 30 psi gage. Air temperature in and out of the intercooler are 105deg C and 44 degC, respectively. Final discharge pressure is 100 psi gage, while suctionis estimated to be 14.4 psi. Determine the compression efficiency.
The absolute steam entry velocity of a single-stage impulse turbine is 600 m/s, nozzle angle is 20°, ratio of blade speed to whirl component of steam speed is 0·5, blade velocity coefficient is 0·85. Find- (a) the blade angles at inlet and outlet if the steam enters without shock and leaves the blade in an axial direction, (b) power developed if the steam flow rate is 5 kg/sec, (c) blade or diagram efficiency and (d) axial thrust.
A reciprocating piston compressor has the following:-Piston diameter of 300mm,-Stroke of 450mm,-Intake pressure of 1 bar,-Intake temperature of air at 200C,-Clearance volume of 3%,-Rotational speed N = 250rev/min,-Discharge pressure = 40 bar,-Compression and Re-expansion are polytropic process with k = 1.25a) Find the compressor’s characteristics (V,P T at all points A,B, C, D).b) Calculate the work and power of the compressor.
A single-cylinder vertical atmospheric engine with a 1.2m bore and a piston of 2700 kg mass is used to lift a weight. Pressure in the cylinder after combustion and cooling is 22 kPa, while ambient pressure is 98 kPa. Assume piston motion is frictionless. Calculate: (a) Mass which can be lifted if the vacuum is at the top of the cylinder and the piston moves up. [kg] (b) Mass which can be lifted if the vacuum is at the bottom of the cylinder and the piston moves down.[kg]
A two stage compressor with first stage piston displacement of 94,390 cm3/sec is driven by a motor. Motor output is 35 HP, suction temperature is 22 °C, volumetric efficiency is 85%, mechanical efficiency is 95%, the intercooler pressure is 30 psi gage. Air temperature in and out of the intercooler are 105 °C and 44 °C. Final discharge pressure is 100 psi gage, suction estimated at 14.5 psi. Find the power saving by intercooler and heat removed in the intercooler in Kilowatts.
Calculate the maximum attainable power in Watts from a horizontal axis wind turbine with a rotor radius of 300 mm with an average wind speed of 12 m/s. Atmospheric air is at 1 bar and 21.1°C.
a. Given the static head of 28.91 m, and static pressure head of 3.15 cm WC. What is the normal pressure, Pn? b. What is the Static efficiency of the fan if the air flow rate is equal to 3.8 5m /sec, total head of 68.72 m, velocity head of 30.86 m, mechanical efficiency and power are 39.12% and 35.72 KW at 30.69°C, respectively. c. Solve for the area at entrance of the fan blade, if the it has a 346mm diameter, flow of air is equal to 23.328 m/se and flow rate of 3.05 m³ /second.
The pressure ratio during the constant volume portion of combustion in a Dual Combustion engine is 1.89 . If the pressure at the end of the constant volume addition of heat is 4.49 , what is the pressure at the beginning?