Assume that routing works in the diagram shown below. PC1 sends an ICMP ECHO request to PC2. Which MAC address will be shown when PC2 receives such packet?loopback1.1.1.1/3210.0.2.0 24loopback12.2.2.2/32DHCP Service:Enabled1.DHCP Service: Enabled.210/010 010 2410 0 3.0 24OSPF Area 0t0/101ethoethoVPCSVPCSPC1PC2R1 f0/1R2 f0/1R2 f0/0R1 f0/0PC1

For sending data packets from one system to another system, intermediate routers are used. These…

Assume that routing works in the diagram shown below. PC1 sends an ICMP ECHO request to PC2. Which MAC address will be shown when PC2 receives such packet? leopback 2.2.2.2/32 loopback 10.0.20/24 DHCP Servicelnale DHCP Service: Enabled 10.010 24 10.0 3.0 24 OSPF Area 0 ton etho etho VPCS VPCS PC1 R1 f0/1 R2 f0/1 R2 f0/0 R1 fO/0 O 000

Assume that routing works in the diagram shown below. PC1 sends an ICMP ECHO request to PC2. Which MAC address will be shown when PC2 receives such packet? leopback 2.2.2.2/32 loopback 10.0.20/24 DHCP Servicelnale DHCP Service: Enabled 10.010 24 10.0 3.0 24 OSPF Area 0 ton etho etho VPCS VPCS PC1 R1 f0/1 R2 f0/1 R2 f0/0 R1 fO/0 O 000

Comptia A+ Core 1 Exam: Guide To Computing Infrastructure (mindtap Course List)

10th Edition

ISBN:9780357108376

Author:Jean Andrews, Joy Dark, Jill West

Publisher:Jean Andrews, Joy Dark, Jill West

Chapter8: Network Infrastructure And Troubleshooting

Section: Chapter Questions

Problem 2TC

See similar textbooks

Similar questions

After establishing a connection with the local DNS server PC1 now knows the IP and MAC addresses of PC2. Suppose PC1 [IP Address: 192.168.2.1, MAC Address: 0010.1191.A946] is sending an ARP packet to PC2 [IP Address: 192.168.2.2, MAC Address: 0110.1290.AD23]. What will be written in the target MAC address before the packet reaches PC2 ?
ARP is necessary for the communication amongst the Hosts, justify this statement. Look at the following bits of ARP and clearly mention Source MAC Address, Destination MAC address, Type of ARP, Source IP & Target IP
Explain in detail how a computer technician would go about statically setting up theIPv4 address 192.168.10.25 in Windows 10 with its default subnet mask and a Router and DNS address of 192.168.10.2
Consider the LAN below consisting of 12 computers (A-L) connected by two Ethernet bridges. At t=0 the bridging table entries for both bridges are empty. At t = 1, node L sends to node E, and node E replies immediately (well before the next time step). What are the (MAC address, interface) entries in the bridging tables right after these transmissions? Note: interface = port number a) Left-hand-side bridge: (L,15), (E, 8). Right-hand-side bridge: (L,7), (E, 5). b) Left-hand-side bridge: (L,8), (E, 8). Right-hand-side bridge: (L,7), (E, 7). c) Left-hand-side bridge: (L,15), (E,5). Right-hand-side bridge: (L,7), (E, 8). d) Left-hand-side bridge: (L,8), (E,8). Right-hand-side bridge: (L,7), (E, 7).
Use given Figure 1 to configure a two-router network. All router configurations must be assumed and done using a PC connected to the router’s console port through its RS232 serial port. Configure all interfaces of ONLY Router A. Please write all necessary commands/RIP version etc.
Each of the following is true regarding TCP SYN port scanning except_______. a. it uses FIN messages that can pass through firewalls and avoid detection. b. instead of using the operating system's network functions, the port scanner generates IP packets itself and monitors for responses. c. the scanner host closes the connection before the handshake is completed. d. this scan type is also known as "half-open scanning" because it never actually opens a full TCP connection.
Question 10 The following figure shows a scenario of insertion attack in which packet "O" has a bad checksum. Why does NIDS let the packet pass through? Question options: NIDS cannot detect the packet "O" NIDS is not allowed to check the checksum of each packet NIDS does not check single letter packet NIDS is not programmed to validate the checksum of each packet. Question 13 What is the purpose of the following traffic? Question options: discover open UDP ports discover open services discover open ICMP ports discover live hosts
Assuming standard 1500 byte Ethernet max payloads: how many IPv4 fragments will be needed to transfer 2000 bytes of user data with a single UDP send? And, how do the 2000 bytes get split over the frags?
Question 1. a. At transport layer UDP uses checksum to detect errors in the received data. Suppose areceiver received 1 1 1 0 1 0 1 1 0 0 1 0 0 1 1 0 and 1 1 0 0 1 1 1 0 1 0 1 0 1 0 1 0 1 as UDP data.What will be the checksum value, please calculate?b. What is ICMP and its functionality? Give two example protocols of application layer thatuses ICMP protocol.
The process by which a base station or access point moves from one base station subsystem to another is known as wireless migration.To connect an AP to a switch, the packet must be updated with a forged MAC address. But why is this the case?
What does a cybersecurity analyst know about their target if they receive a RST packet back from a target host? The target is using UDP rather than TCP. The target expects the PSH flag to be set. The destination port is open on the target host. The source port in the RST message is closed. Which one of the following could a cybersecurity analyst enumerate using wpscan on a WordPress site? Administrators Plug-ins Posts Versions What program would a cybersecurity analyst use to enumerate services? enum4linux Nmap Snmpwalk Smbclient
1. Consider the network setup shown below. Assume that switch 3 has an empty switch table. Which of the following would be the entry on its switch table when it receives the packet from user 7? Select from the options below MAC Address of User 3 | Interface 3 | TTL of packet from User 1 MAC Address of User 7 | Interface 2 | TTL of packet from User 1 MAC Address of User 3 | Interface 1 | TTL of packet from User 7 MAC Address of User 7 | Interface 2 | TTL of packet from User 7 MAC Address of User 7 | Interface 1 | TTL of packet from User 1 2. Suppose user 1 transmits to user 7 and the switch tables of switch 1 and 2 are empty while the switch table of switch 3 contains information on user 7. How will switch 2 behave when it receives the packet? Broadcast the packet to user 4, user 5, switch 1, and switch 3. Send the packet to switch 3. Discard the packet since user 1 is not connected to any interfaces of switch 2. Send back the packet to…