Assume that you measure the dimensions of a hollow cube with a vernier caliper many time and obtain the following average values in cm: Height: 1 Inner width: 1 Outer width: 1.1 Inner length: 1 Outer length: 1.2 Using these values, calculate the volume of the hollow cube in cm3. Express your result with 3 significant figures.

Assume that you measure the dimensions of a hollow cube with a vernier caliper many time and obtain the following average values in cm: Height: 1 Inner width: 1 Outer width: 1.1 Inner length: 1 Outer length: 1.2 Using these values, calculate the volume of the hollow cube in cm3. Express your result with 3 significant figures.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 62P: A certain hydraulic system is designed to exert a force 100 times as large as the put into it. (a)...

See similar textbooks

Similar questions

The length of a rod is 4ft and the linear density at the center is 2 kg/ft. The measure of the linear density at a point on the rod varies directly as the third power of the measure of the distance of that point from the left end of the rod. Set-up the definite integral that will give the center of the rod.
How long a piece of wire would you need to form a circular are subtending an angle of 1.4 rad, if the radius of the are is 8.1 cm?
Assume that you measure the dimensions of a hollow cube with a vernier caliper many time and obtain the following average values in cm: Height: 1 Inner width: 1 Outer width: 1.2 Inner length: 1 Outer length: 1.2 Using these values, calculate the volume of the hollow cube in cm3. Express your result with 3 significant figures.
Consider a conical enclosure of height h and base diameter D. Determine the view factor from the conical side surface to a hole of diameter d located at the center of the base.
"Painting the entire exterior surface of a cube with edge length S = 1.26 meters reduces paint level by 2 inches in a cylindrical paint can with radius R = 3.24 inches. Assuming the paint is put on with a uniform thickness, calculate this thickness in inches." Hmm... I don't think the paint can height is necessary... at least, it wasn't given in the problem. I started out by calculating the volume of the 2 inches removed from the can, and, knowing that the volume would stay the same, tried to figure out how to put the volume onto the surface of the cube. That's where I got stuck. Any ideas? Thank you!
The volume of a sphere is given byV=(4/3)πr^3, whereris the sphere’s radius. For solid spheres with the same density – made, for example, from the samematerial – mass is proportional to volume. The table below lists measures of deameterand mass for different steel balls. (a) Determine the quantity that, when you plot mass against it, should yield a straightline. (b) Make your plot, establish a best-fit line, and determine its slope (which in thiscase is proportional to the spheres’ density Diameter (cm) 0.75 1.0 1.56 2.16 2.54 Mass(g) 1.81 3.95 15.8 38.6 68.2
How do you find the area of this? I had to do an experiment where you take a styrofoam cup and poke a flashlight through the bottom of it, then shine the light onto a wall from different distances and measure the diameter. I have to calculate the area. It it just pi*r^2? That's what I did, but then I've seen someone else use 4*pi*r^2 and that confused me. I want to make sure I done it right.
A certain hydraulic system is designed to exert a force 100 times as large as the put into it. (a) What must be the ratio of the area of the cylinder that is being controlled to area of the master cylinder? (b) What must be the ratio of their diameters? (c) By what factor is the distance through which the output force moves reduced relative to the distance through which input force moves? Assume no losses due to friction.
Use dimensional analysis and show that the expression e=mc^2 has a unit of energy.
You are tasked to measure a 2.1 m door with using only a ruler. On yourfirst try, you recorded a measurement of 214 cm. You repeat themeasurement and obtain a value of 216 cm. What is the value of the truepercent relative error considering your most recent measurement?
The solutions you have sent they have solved it for 0.89m which is very easy solution. But since in question it's not mentioned so it should be done for elongation all the time
Using the value of 1.29 gcm^3as silk density, calculate a fiber equivalent diameter in μm if such fiber linear density was 0.99 den.