4. Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is the angular velocity of each pulley if the belt has a constant speed of 5 m/s? What is the frequency and the period of each pulley? (b) What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time?? R₁ R₂ R₁ 2 R₁ -0.3 m R₂ = 0.2 m R3 -0.1 m

4. Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is the angular velocity of each pulley if the belt has a constant speed of 5 m/s? What is the frequency and the period of each pulley? (b) What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time?? R₁ R₂ R₁ 2 R₁ -0.3 m R₂ = 0.2 m R3 -0.1 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

. During the operation of a punch press, its flywheel decelerates uniformlyfrom 400 rpm to 200 rpm in l sec. The rim of the flywheel weighs 1288 lb, itsinside and outside diameters are 56 in. and 60 in., and it is attached to itshub by 6 spokes. What average shearing force is developed between the rim andeach spoke during the 1 sec interval?
(ii) A cam, with a minimum radius of 25 mm, rotating clockwise at a uniform speed is to be designed to give a roller follower made of 20mm diameter at the end of a valve rod, motion described below : 1. To raise the valve through 54 mm during 124° rotation of the cam by simple harmonic motion 2. To keep the valve fully raised through next 32° 3. To lower the valve during next 60° by uniform acceleration and retardation. Determine the maximum velocity and acceleration of the valve rod when the cam shaft rotates at 112 r.p.m and write the remaining dwell angle.
An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number. An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number.
A 2.5 ft diameter flywheel of a gas engine has a pulley 10 in. in diameter bolted to it (both turning together). The flywheel turns at a speed of 150 rpm. Find a. the angular speed of the pulley in radians per second b. the linear speed in feet per minute of a point on the surface of the flywheel c. the linear speed in feet per minute of a belt running on the pulley, assuming no slipping between the belt and pulley surface.
Question No. 18: (a) In an epicyclic gear train, an arm carries two gears A and B having 36 and 45 teeth respectively. If the arm rotates at 150 r.p.m in the anticlockwise direction about the centre of the gear A which is fixed, determine the speed of gear B. If the gear A instead of being fixed, makes 300 r.p.m in the clockwise direction, what will be the speed of gear B? (b) Prove that the resultant unbalanced force is minimum when half of the reciprocating masses are balanced by rotating masses.
Analytically determine the angular displacement of the ram in the rock-crushing mechanismshown below as the 60-mm crank is rotated from its current position 40° clockwise.
A Beyblade is a commercial line of a toy tops. It is spun using a rack (ripcord) and a pinion gear inside the launcher. If the ripcord length is 270 mm and it leaves the launcher for 3 seconds and the diameter of the gear is 20mm.Find the rotational speed of the Beyblade top. If the Beyblade stopped rotating after 2 mins, what is the angular deceleration?
A flywheel weighing 4480 lbs has a radius of gyration of 3 ft. If there is a driving torque of 600 lb-ft, and a resisting torque of 250 lb-ft, find the time required to increase its speed from 20 to 80 rpm. The correct answer is 22.5 seconds.
Link BC (of length 0.47 m) is pin connected at the fixed point C and makes an angleof ⍬ = 51° with the vertical. This link is connected to the vertical link AB (of length0.3 m) and point A is also the axle of a wheel of negligible size that is moving alonga circular track of radius r =2.3 m. If the speed of A is constant and VA = (-2.59)im/s, which one of the following statements is correct? (In the followingstatements, wAB and wBC denote ⍵AB and ⍵BC respectively, where both are definedpositive in the k-direction and given in rad/s, and A denotes the magnitude of pointA's acceleration in m/s2) 1) wAB=0; wBC=0; aA=02) wAB=6,99; wBC=-7.09; aA=03) wAB=8.63; wBC=0; aA=04) wAB=8.63; wBC=0; aA >0 5) wAB=6.99; wBC=-7.09, aA>0
A pulley 250 mm in diameter is belt-driven by a pulley 150 mm in diameter. If the 10-in.- diameter pulley is turning at 120 rpm, determine the belt speed and the rpm of the other pulley.
Wheel, which radius is r=0,4m is rolling without slip with velocity v=3m/s on the plate which is moving with velocity v2=2m/s with respect to the surface. Find the acceleration of the instantaneous center of velocity and the velocity of the instantaneous center of acceleration of the wheel
Two gear wheels with 50 and 30 teeth respectively, mesh externally, the speed of the smaller being 1800 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 18° involute form, addendum length is 8 mm and the module is 5 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact. answer with clear word please.