1At a given instant, the slider block A has thevelocity and acceleration as shown in figure.find the angular acceleration of the link ABat this instant. *B3m45°VA=6 Aaa = 2 m/s3.771 radian per second (ccw)3.771 radian per second (cw)2.828 radian per second (ccw)2.828 radian per second (cw)

Given Data VA=6 m/s aA=2m/s2 rB/A=3(cos45i+sin45j)=2.12i+2.12j

Answered: At a given instant, the slider block A…

At a given instant, the slider block A has the velocity and acceleration as shown in figure. find the angular acceleration of the link AB at this instant.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2. The rotation of a pulley is defined by the relation θ=2t4-30t2 + 6, where θ is measured in radius…

Q: The rotating arm starts from rest and acquires a rotational speed N = 200 rpm in 2 seconds with…

Q: a. At the given instant , mention the constraints at C and D, If there are frictionless ball…

A: (a) At the given instant , Draw the constraints at C and D, If there are frictionless ball bearings…

Q: The given system consists of A, B and C gears. Since gear A rotates clockwise at a constant speed of…

A: The ratio of teeth on the gear to the teeth on the pinion is termed as gear ratio. It is also…

Q: The figure below shows a cargo lift mechanism for a delivery truck At this instant, point A has a…

Q: Draw the position and velocity diagrams of the mechanism (clearly locate point G and K in both…

Q: Motion of the 2L bar is controlled by the constrained paths of A and B. If velocity of the slider A…

Q: Thex- and y-motions of guides A and B with right-angle slots control the curvilinear motion of the…

Q: For the mechanism shown, determine the speed of point C at the instant θ2=130°. Also, determine the…

Q: In reference to the figure, @ 1 ft Given: v = 8 ft/s w = 2 rad/s Determine the velocity in ft/s of…

A: Write the given data. v=8 ft/sω=2 rad/sr=1 ft

Q: The flexible band F is connected in E to the rotating sector and has a constant speed of 4 m/s, as…

A: Given data: Linear velocity of the band=4 ms

Q: Block 2 slides outward on link 1 at a uniform velocity of 6 m/s as shown in the figure. Link 1 is…

A: Given: V=6 m/sω= 20 rad/s

Q: Magnetic tape is being fed over and around the light pulleys mounted in a computer. If the speed v…

Q: (a) Determine the magnitudes of the velocity v4 and acceleration a Ą of point A. (b) Determine the…

A: for solution refer below images.

Q: [Q6] At this instant , find angular acceleration and angular velocity for BC using I- Absolute…

A: 1 2

Q: For the instant shown below in this mechanism, the link OA has a velocity v = 1.5 m/s to the right…

A: Given: Rolling without slipping,Vp=rωω1.5=0.1×ωωωω=15 rad/sec

Q: Link AB has the angular velocity of 2 rad/s and angular acceleration of 6 rad/s². Determine the…

Q: in the figure shown, block B is pulled down with a velocity of 0.3 m/s. Calculate the velocity of…

Q: [Q6] (a) At this instant, find angular acceleration and angular velocity for CD using Absolute…

Q: A linear actuator is connected to link AB at location A. The linear actuator is extending with…

A: GivenVa=9m/saa=-10m/s2

Q: Block 2 slides outward on link 1 at a uniform velocity of 6m/s as shown in figure. Link 1 is…

A: Given:ω=20 rad/sr=100 mmv=6 m/s

Q: The cart has a velocity of 4 ft∕sec to the right. Find the magnitude of velocity on point "B" on the…

Q: The distance y- 1.6 m. Find the upward velocity of A if the downward velocity of B is 2.4 m/s.…

Q: Figure 1 shows a double cursor C formed by two sliding pieces hinged on the bar AB and the circular…

A: Soln:- in this figure slider C slides on the Arm AB. It has two acceleration at Instant. First one…

Q: The flexible belt runs around two pulleys of different radii. At the instant shown. point C on the…

A: Acceleration (a) is the velocity shift (Δv) over a time shift (Δt), expressed by the equation a=a =…

Q: If end A of the constrained link has a constant downward velocity of 2 m/s when 0= 30° degrees find…

A: Acceleration of end B By definition, α = Δω Δt α = Δ ω Δ t. Thus, These equations mean that linear…

Q: The x- and y-motions of guides A and B with right-angle slots control the curvilinear motion of the…

A: Given That y = 16 -0.57t3 We need to find. Velocity Vy at t = 2.5 sec.

Q: the Velocity of car A as observed by an occupant in car B. Illustrate the solution with a schematic…

Q: The disk shown rolls without slipping. Its center O has a speed of 3 m/s and is decelerating at 5…

A: we know that v=rωω=vr =30.4 =7.5rad/s

Q: For the following mechanism, at the instant shown, the velocity and acceleration of the cylinder are…

Q: Given the information provided at an instant, determine the angular velocity and angular…

A: Given, Vb = 4m/s Ab = 2 m/s2

Q: (c) Find the acceleration of point B at the instant. (d) Determine the acceleration and angular…

Q: Figure Q1(b) shows a train travelling along a cireular curve of a radius r= 300 m. At the instant…

A: Given:r=300 mω=0.03 rad/sα=0.0015 rad/s2

Q: At a given instant, the sliding block is traveling to the right with the speed and acceleration…

A: Given data as per the question vB =6 in/s =0.15 m/s aB = 3 in/s2 = 0.075 m/s2 Calculations The…

Q: The clockwise angular velocity of link AB is shown for an instant. Using vector analysis, determine…

Q: The given system consists of gears A, B and C. consists of. A gear clockwise 600 revolutions per…

A: Given DatarA=50mmNA=600rpmrB=100mmrB'=50mmrC=150m

Q: Problem 3 For the instant represented, link CB is rotating counterclockwise at a constant rate N=4…

Q: The rod of length L pivots on a block that slides along a horizontal shaft as shown in the diagram…

A: Given: The length of the rod is L. The rotational motion is not given, so θ ̇ = 0 The relative…

Q: Apply the instantaneous centre method at the instant and determine the angular velocity at of CB .…

Q: Member AB has the angular motion shown. Determine the velocity and acceleration of the slider block…

Q: Find the angular velocity and angular acceleration of sleeve A. B

A: Solution: Given Data:

Q: The x- and y-motions of guides A and B with right-angle slots control the curvilinear motion of the…

Q: Find the acceleration of the translating piston at the given instant if w = 10 rad/s And a, = -5…

Q: Thex-and y-motions of guides A and B with right-angle slots control the curvilinear motion of the…

A: given; x=18+0.67t2y=18-0.61t3x and y in mm.velocity at t=3s

Q: Find the angular velocity and angular acceleration of the wheel according to the values given in…

A: Theory of Machines is the branch where kinetics and kinematics of the mechanism are studied.…

Q: Q3. At the instant 0 = 50° , the slotted guide is moving upward with an acceleration of 3 m/s? and a…

A: Given Data- Find- Q = 50o…

Q: C for 36" 48" 12" A 4 ft/sec L 5 ft

A: Let us consider, Tangential acceleration at C = at Centrifugal acceleration at C = aC Velocity of…

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

1
At a given instant, the slider block A has the
velocity and acceleration as shown in figure.
find the angular acceleration of the link AB
at this instant. *
B
3m
45°
VA=6 A
aa = 2 m/s
3.771 radian per second (ccw)
3.771 radian per second (cw)
2.828 radian per second (ccw)
2.828 radian per second (cw)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

ABCD is a four-bar chain with link AD fixed. The lengths of the links are AB = 70mm; BC = 175 mm; CD = 100 mm; and AD = 200 mm to be horizontal (fixed link).The crank AB rotates at 20 rad/s clockwise. Draw the velocity and accelerationdiagram when angle DAB = 45° and B and C lie on the same side of AD. Find theangular velocity and angular acceleration of links BC and CD.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Vince Carlo is a world-renowned skateboarder who wants to try a new skateboard design. The skateboard has a length of lAB = 1.30 m. Given the figure shown, determine (a) the velocity at point B and (b) the angular velocity of the skateboard AB if the velocity at point A is vA = 2.9 m/s to the right. Neglect the diameter of the wheels.Note: Use purely Relative Motion Analysis (RMA) Method for velocity calculations.
In the mechanism shown below, link AB rotates at a constant angular velocity of 1.5 rad per sec counterclockwise. What is the acceleration of C along the channel? Assume the positive direction to be upwards and to the right.
At a given moment four link mechanism OABO1, is in the position shown on the figure and OA=AB=AO1=3√ 2 m.Link OA rotates at constant angular velocity ω1= 5 s−1.Find the angular velocity ω3 and angular acceleration α3 of link O1B.
For the mechanism shown on the figure WBC =const= 5 s-1 OA=BC=0,3m , AB=0.6 m Determine ; a)velocity an acceleration of the Point B b)angular acceleration of the body BC c)angular velocity and angular acceleration of the body OA d)linear velocity and acceleration of the Point A
Q2B=1in;BC=3in.; ω2=1rads,constant. Find the absolute linear acceleration for point C. Hint: for constant angular velocity, angular acceleration is zero. Using semi-graphical approach
The power of an engine running at 125 rpm is turned off and the engine comes to rest at the end of 2 min and 40 sec. Assuming that there is no slipping between the belt and pulley surface and that the deceleration is uniform, find 1) the average speed in radians per second of the engine pulley in coming to rest; 2) the total angular distance traveled in revolutions, radians and degrees in coming to rest; 3) the distance in feet traveled by a belt running on the pulley in coming to rest, if the pulley diameter is 3ft.
find an acceleration of the center of the beam (marked as a blue point) which is connecting both wheels , if it is known that linear velocity ot the wheels v=100km/h, r=0,8m and the distance drom the center of the wheel and the pont where the beam is connected (marked as red red distance)=0,4m, there is no slipping between wheels and the ground
Figure below is a crank and slider mechanism. Link AB rotates on a counterclockwise manner with angular velocity of 6 rad/s. Then, slider C moves along Link AB with speed or (4t^2 ) m/s, where t is in seconds. Determine the magnitude of velocity and acceleration of slider C when t = 0.75 s.
In the given figure, A link OB is rotating with a constant angular velocity of 2 rad/s in counter clockwise direction and there is a block is sliding radially outward on it with an uniform velocity of 0.75 m/s with respect to the rod, If OA = 1m , find the magnitude of the absolute acceleration of the block at location A ?
In Fig. below the angular velocity of the crank OA is 600 r.p.s. Assume crank is rotating with constant velocity.Determine the linear velocity and acceleration of the slider D and the angular velocity and angular acceleration of the link BD, when the crank is inclined at an angle of 75° to the vertical. The dimensions of various links are: OA = 28 mm; AB = 44 mm; BC 49 mm; and BD = 46 mm. The center distance between the centers of rotation O and C is 65 mm. The path of travel of the slider is 11 mm below the fixed point C. The slider moves along a horizontal path and OC is vertical.
At that instant shown below, Q2F= 15 inch, Q4B= 14 inch, Q4D= 6 inch, Q4E= 15 inch, Q2Q4= 15 inch. The crank Q4D is rotating uniformly counterclockwise at 150 rpm. Find the absolute instantaneous linear velocity in fps of point F and E and the absolute instantaneous angular velocity in rpm of the variable length crank Q2F. (USE RELATIVE VELOCITY METHOD). ?= 40