Answered: At a point in plane stress the…

At a point in plane stress the principal stresses were found to be 22 MPa(T) and 14 MPa (C). The maximum shear stress at the point is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: What happens when the in-plane principal stresses are of opposite signs?

A: Principal planes are those planes on which there is no shear stress. The stresses on these planes…

Q: etermine the normal stresses in bronze rods (1) and steel rod (2) after

Q: Find the stresses at points A andB on the plate shown in the figure.

A: The normal stress at the points A and B can be determined as,

Q: The major and minor principal stresses are 3 MPa and -3MPA respectively. The maximum shear stress at…

A: Given data : Major principal stress=3 MPaMinor principal stress=-3 MPa

Q: At a point in a stressed body, the cartesian components of stress are Oxx = 60 MPa, Guy = -40 MPa,…

A: Given Data σxx=60 Mpa σyy=-40 Mpa σzz=20 Mpa τxy=-40 MPa τyz=20 MPa τxz=30 MPa Stress tensor,…

Q: At a point on the free surface of a stressed body, the normal stresses are 20 ksi (T) on a vertical…

Q: How can we find the maximum normal and maximum shear stress at the point?

A: Normal Stress: Normal stress is the amount of stress that occurred in a member when it is loaded by…

Q: 3. At a point in a strained material, the principal stresses are 100 MPa and 50 MPa both tensile.…

Q: A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the…

A: Given Data⇒ Line shaft rotating at (N)=320 rpm Power transmitted (P)=35 KW Allowable shear stress…

Q: A thin-walled cylinder has an internal diameter of 1200 mm and has walls 1.2 mm thick. It is…

A: For solution refer below images.

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner radiu…

Q: Determine the minor principal stress and position of the principal plane when a block is subjected…

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: 1. Show that pure shear gives rise to tensile and compressive stresses across the planes inclined at…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Given: σx=62 MPaσy=-85 MPaτxy=56 MPa Solution: Sign convention: The tensile stress is positive The…

Q: the stresses at point A.

A: To find Stresses at point A

Q: 3. An element in a strained body is subjected to a tensile stress of 100 MPa and a shear stress of…

A: When an amount of force act on an object, then the force has the tendency to change the shape of the…

Q: A point is subjected to tensile stresses of 200 MPa and 150 MPa on two mutually perpendicular planes…

A: Stress is defined as the resistance force acting per unit cross-section area of the body. It is also…

Q: If o = 50 ksi, Oy = 10 ksi, and Txy = 30 ksi, what is the absolute maximum shear stress for the…

Q: Determine: (a) principal planes, (b) the principal stresses (c) the orientation of the planes of…

Q: 10 MPа 4 ksi 10 MPа 4 ksi 10 MPа 2 ksi

A: Mohr circle is a graphical method to determine principal stresses. It's plotted on a graph between…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts of a…

Q: 80 MPa 60 MPa

A: Consider the given plane figure on x-y plane. From the figure, Stress in x direction = σx = 0 MPa…

Q: For the state of plane stress shown below, determine the principal stresses, the maximum in plane…

Q: tical planes at the point are Sx = 0 MPa, Sy = 54 MPa, and Sxy = 17 MPa. w Mohr's circle for this…

Q: determine (a) the principal stresses at K, (b) the maximum in-plane shear stress and average normal…

Q: Q2: For the stresses at the point shown, find: The maximum shearing stress. • The principal stresses…

A: To Find : the maximum shearing stress the principal stresses and planes Given : stress acting…

Q: In a biaxial state of stress, normal stress are 900 N/mm^2 and 100 N/mm^3 in x and y diretion…

A: Given data σx=900 MPaσy=100 MPaτxy=300 MPa

Q: In the figure shown, assume that a 21.3-mm- diameter rivet joins the plates that are each 118 mm…

A: Given Data Diameter of riveted joint is :d=21.3 mm width of plates is : W=118 mm Bearing stress is…

Q: Current Attempt in Progress Consider a point in a structural member that is subjected to plane…

Q: A torque and two forces seen in the figure are applied. the diameter is 65mm. Determine the…

Q: The normal stresses at a point are o, = 80 MPa and oy = 20 MPa; the shear stress at this point is…

Q: The 4-In. diameter shaft shown above is made from a ductile brass alloy. Which of the following are…

A: Normal Stress = Force / Cross Section Area = 4*100 / (π 4^2) = 7.957747154 Ksi Shear force is to be…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: Oy Ot Txy a Tnt Ox On (b) (a) On the surface of a structural member, stresses are given as ox=67,9…

A: Given data: The stress in x-direction is σx=67.9 MPa The stress in y-direction is σy=25.5 MPa The…

Q: Consider a point in a structural member that is subjected to plane strèss. Normal and shear stress…

A: given; stress in x direction(Sx)=41MPastress in y direction(Sy)=11MPashear stress in xy plane…

Q: Determine the minor principal stress and position of the principal plane when a block is subjected…

A: given data: stress in x direction(σx)=100MPa(tensile)stress in y direction…

Q: Q4- Draw Mohr's circle for the case as seen in Fig. 4. Determine the principal stresses and the…

A: According to the given information we have stress in x-direction and stress in the y-direction and…

Q: 1 MPа 2- For the state of stress as shown below, 2 МPа a) Find principal stresses З МРа b) Draw…

Q: At a point in a material under stress there is a compressive stress of 200MN/m2 and a shear stress…

Q: A state of stress at a point A is given by ax = 29 MPa, oy =- 195 MPa, and txy = -3.751 Which of the…

A: Data given- σx = 29 MPa σy = 195 MPa τxy = -3.75 MPa

Q: Find the maximum shear stress at a plane if the major and minor principal stresses at a point are 3…

Q: A state of stress at a point A is given by σx = -75 MPa, σy = 122 MPa, and τxy = -3.75 MPa. Which of…

A: Given σx = -75 MPa σy = 122 MPa τxy = -3.75 MPa

Q: At a certain section in a material under stress, direct stresses of 45 MN/m2 tensile and 75 MN/m2…

A: Given Data : Direct Stresses are

Q: A block is subjected to the stresses as shown in Fig. 1. If the allowable compressive normal stress…

Q: Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…

A: Punching is a process is used to make holes in the sheet metal by forcing a tool which is called a…

Q: At a point in a stressed body the state of stress on two planes 45° apart is as shown below.…

A: Given:σx=8 MPaτxy=3 MPaθ=45o

Concept explainers

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.

Question

100%

Help

8
At a point in plane stress the principal
stresses were found to be 22 MPa(T)
and 14 MPa (C). The maximum shear
stress at the point is
(ähäi 2)
MPa 18
MPa 11
MPa 4
MPa 6.5
no correct asnswer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

How can we find the maximum normal and maximum shear stress at the point?
Show whether it is safe by calculating the stresses at point A according to the Tresca Criteria. (Diameter: 20 mm, σA = 320 MPa)
SS 304 steel shaft is 3 m long and has an outer diameter of60 mm. When it is rotating at 60 rad/s, it transmits 30 kWof power from the engine to the generator. Determine thefollowing: a. The smallest thickness of the shaft if the allowableshear stress is 150 MPa and the shaft is restricted notto twist more than 0.08 rad. Use G for steel = 83 GPa. b. The percentage savings in weight had the generatorutilized a solid shaft. Assume same material, length andtorque capacity.
Internal loadings at a critical section along a steel drive shaft are given. If theyield stress under tension and shear are S_y = 800 MPa, respectively, determine the maximum length of the shaft using the maximum-shear-stress theory (Tresca yield theory) in a way that the shaft does not fail neither at A nor at B. （DON'T COPY OTHER ANSWER) AND 30mm is radius
Help me determine Maximum shear stress
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
Q2. A mild steel shaft transmits 21 kW at 250 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa.
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the diameter (mm) of the A premium?
Internal loadings at a critical section along a steel drive shaft are given. If the yield stress under tension and shear are S_y = 800 MPa, respectively, determine the maximum length of the shaft using the maximum-shear-stress theory (Tresca yield theory) in a way that the shaft does not fail neither at A nor at B
Question : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further subjected to a torque of 10 kN-m. The maximum principal stress experienced on the shaft is closest to a) 41 MPA b) 82 MPA c) 164 MPA d ) 204 Mpa
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.The shear stress in the shaft is limited to 50 MPa. Determine the inside and outside diameters of theshaft, if the ratio of the inside to the outside diameter is 0.4. [Ans. 35 mm ; 90 mm]