Show whether it is safe by calculating the stresses at point A according to the Tresca Criteria. (Diameter: 20 mm, σA = 320 MPa)

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11633 N force. - 540…

A: P= 11633 N Width of the cross section, b= 60 mm Height of the cross section, h= 180 mm

Q: A mild steel shaft transmits 22 kW at 550 r.p.m. It carries a central load of 900N and is simply…

A: Given Data  Power, P=22KW Shaft rpm, N=550 rpm Load, P=900N Length of the beam, L=2.5m  Allowable…

Q: 3. If o, = 30 ksi, o, = 20 ksi, and ty = 10 ksi, what is the maximum in-plane shear stress in ksi? →…

A: Given:σx=30 ksiσy=20 ksiζxy=10 ksi

Q: The beam is supported by two rods AB and CD that have cross- sectional areas of 13 mm² and 7.8 mm²,…

A:

Q: A hollow iron pipe with outside diameter of 240 mm is used as a column to carry a load of 80 kN.…

A:

Q: For a cylindrical steel pressure vessel of inner diameter 50 in and constant wall hickness 0.125 in,…

A: Inner diameter of vessel, Di=50 in,Thickness of vessel, t=0.125 in,Pressure inside the vessel, P=200…

Q: The pipe shown in Fig a has an inner radius of 40 mm and an outer radius of 50 mm. If its end is…

A: Given Inner radius of pipe = 40 mm Outer radius of pipe = 50 mm To find The shear stress inner and…

Q: :O38/ Given the followtng data, the chear stress value at segment BC is G 80 GPa Diameter= 2e m 沙…

A: Find the shear stress in segment BC.

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: GivenAxial load P=115.33kNT section cantilever beam as shown below

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

A: Consider below figure for the given question: We are given, Load = P = 2000 lb Diameter of pulley =…

Q: Determine the shear stress Try that acts at point A. Express your answer to three significant…

A: Solution: GIven Data: d = 40 mm Fx = 1350 N Fy = 540 N Fz = 920 N

Q: H.W.8: Calculate the stresses, if the strains displayed on the lement have been applied. Use all…

A: To obtain the required stresses, we must first determine the principal strains in the element using…

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: Given: The load is 115.33 kN. The T cross section is shown below:

Q: If P =125 kN Determine the normal stresses of members DH & HG in (kPa). The diameter of each member…

A:

Q: - 540 mm 180 mm- 180 mm 60 mm → - B 30 kN

A:

Q: Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A:

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force. E4.png…

A:

Q: A spherical pressure vessel has an inner radius of 5 ft and a wall thickness of 0.5 in. Draw Mohr’s…

A: Given data r=5 ftt=0.5 inP=80 psi

Q: Part A a. Take T = 650 N. m and T, = 1565 N. m. Determine the maximum shear stress developed in the…

A:

Q: What is the maximum shear stress RESULTING FROM THE COMBINATION OF THE FOLLOWING stresses: Tesile…

A: Given data: Sx=200 MPaSy=100 MPaSS=50 MPa Need to determine the maximum shear stress.

Q: Help me determine   Maximum  shear stress

A: Given data : Normal stress in X direction σX=-12 MPaNormal stress in Y direction (σY)=0 MPaShear…

Q: 80 MPa 60 MPa

A: Consider the given plane figure on x-y plane. From the figure, Stress in x direction = σx = 0 MPa…

Q: Determine the limiting peripheral velocity of a steel ring if the allowable  stress is 20  ksi the…

A:

Q: Determine maximum shear stress Maximum principal stress=25 MPa Minimum principal stress=-5 MPa

A: Maximum principal stress, σmax=25 M PaMinimum principal stress, σmin=-5 MPa

Q: A pressure vessel with an internal pressure of 400 psi is fixed at one end. At its free end, two…

A: Px=10kipsPy=15kipsPz=5kipsD=10 ind=9.6 in

Q: Determine the average normal and shear stresses at a cross section (a-a) for e-65. The member has a…

A: Draw the F.B.D of the given cut section of the element.

Q: 6. A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The allowable shear stress for the…

A: Answer: The diameter of the shaft is 50 mm.

Q: Figure. rod 2m. 2m. 60

A:

Q: QI/ For the assembly below, determine the average normal stress for the cable. Assume that the cable…

A: Given Data  Load, P=12 KN d=10 mm Let us draw all the reactions

Q: Maximum shear stress (Tresca) criterion whether the diameter d is safe using ch

A:

Q: 2.2 in. in.- A IB = in. 1.6 in. e maximum and average stresses in sections A and B, take t = 0.45 in

A: Stress concentration is defined as the localization of high stresses due to the irregularities…

Q: Arshadadhom shubber H.W. 2: A 60-mm-wide by 8-mm-thick steel plate is connected to a gusset plate by…

A: Given data,  P= 70 kN  L=60 mm  d= 20 mm (pin diameter)  t= 8 mm

Q: From the figure shown, the diameter of each segment is indicated. Determine the average normal…

A:

Q: A steam turbine rotor is 160 mm diameter below the blade ring and 25 mm thick. The turbine is…

A: A steam turbine rotor has a diameter of 160 mm below the blade ring and is 25 mm thick.The turbine…

Q: A horizontal cantilever 2 m long is constructed from z-section shown in Fig. 9.19. A load of 10 kN…

A: As indicated in the illustration, we have a 2 m long horizontal cantilever made of z-section.A 10 kN…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A:

Q: Select the right value of the stress occurred on a hollow shaft when it is subjected to a twist of…

A:

Q: The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius  of 260…

A: The pressure difference between the inner and outer surfaces of a cylinder applies stress on the…

Q: 11 A crane hook is of trapezoidal cross-section hav- ing inner side 80 mm, outer side 30 mm and…

A: A crane hook has an inner side of 80 mm, an outside side of 30 mm, and a depth of 120 mm.The inner…

Q: Dmm Ø20 0,1 Ø10 20 2. Draw diagram of normal stresses.

A: Here bending stresses will be normal stresses. The normal stresses diagram drawn in step 2.

Q: A aluminum tank with a wall thickness of 2mm and radius of 120mm is 9m long was pressurized to…

A:

Q: determine the normal stresses in rod 1 (0₁) in

A:

Q: ROKNE 20KN 50m2

A:

Q: Determine the factor of safety as per tresca's max shear stress theory

A: Given: A machine element is subjected to the following bi-axial state of stress:σx=80 MPaσy=20…

Q: Determine the minimum required failure shear stress "T" for t

A: Given: d=20 mm FS= 1.8 To determine: The minimum failure shear stress

Q: Calculate the principal stresses o 1 at point A of cross-section aa. Data: L = 0.3 m; F = 0.9 kN.…

A:

Q: Solve Prob. using the maximum shear stress theory.

A: In mechanical engineering most of the components are made up of the mild steel. so assume the…

Q: Determine the stress in each cord for the system shown in fig. below, if the cross section area of…

A: To find: The stress in each cord. Given: The area of the each cord is A=650 mm2. Formula used: The…

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.