At a point of a material, the stresses forming a two-dimensional system are shown in Figure Q1. By using Mohr's circle of stress method: - (i) determine the magnitudes of the principal stresses. (ii) determine the directions of the principal stresses. (iii) Examine the value of the maximum shearing stress

At a point of a material, the stresses forming a two-dimensional system are shown in Figure Q1. By using Mohr's circle of stress method: - (i) determine the magnitudes of the principal stresses. (ii) determine the directions of the principal stresses. (iii) Examine the value of the maximum shearing stress

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.18P: Repeat the previous problem using sx= 12 MPa.

See similar textbooks

Similar questions

If the Young’s modulus and rigidity modulus of a material are 210GPa and 70GPa respectively, calculate the Poission’s ratio of that material. a. 0.111 b. 1.111 c. 0.500 d. 0.801
– The weight is suspended from structural A–36 steel alloy and 2014-T6 aluminum alloy wires, eachhaving the same initial length of 10 ft and cross-sectional area of 7×10–3 in2 (Figure Q1). If the weight is increasedgradually, determine which wire yields first? Explain which material model and yield criterion you will use? Justifyyour choices
If an isotropic material has a shear modulus of 21 Gpa and a Poisson’s ratio of 0.4, calculate its Young’s modulus. Select one: E = 59 Gpa E = 300 Gpa E = 30 Gpa E = 80 Gpa E = 450 Gpa
Find the amount of depression in mm at the midpoint of the bar AB.Mo = 1kNm, L = 1m, E = 200 GPa, I=1x106 mm4
The figure shows a sign hanging from a beam anchored to a wall by two cables. In an element of the beam, the stress tensor has been measured, resulting in the following values σxx = 2250 [psi], σyy = 1175 [psi] and ???=−820 [psi]. Q) It is known that σcreep= 2000 [psi]. Is it possible that the beam could fail? Apply the von mises and tresca criteria
A [0/90/0/±45]s Glass/Epoxy laminate is subjected to the following mechanical loads: Nx =Ny= 80*10^5 N/m. The thickness of each lamina is 0.25 mm. Longitudinal modulus of elasticity = E1 = 38.6 GPa , Transverse modulus of elasticity = E2 = 8.27 GPa , Poisons Ratio 0.26. a) Determine the local stresses at the top of 45° ply
If the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3 respectively, What is the axial strain in the cylinder wall at mid-depth?
K=17 so 107 MPa strength of material question.
Q1] A bending moment due to load applied on the head of femur bone which is offset by a distance (x= 50 mm) off the bone center for a person standing in relaxation.His weight is 70kg. 1. Find the maximum bending stress induced due to the weight and compare it to the maximum comp. stress. R= 20mm t= 12mm. 2. Draw the expression for the second moment (I) basing on min-wall hollow cylinder. 3. Find the principal stress σ1, σ2, τx1y1, and the angle θp for point C and D shown.
A machine element is subjected to the following bi-axial state of stress; sigma x = 80 MPa; sigma y = 20 MPa; Txy=40 MPa. If the shear strength of the materials is 100 MPa, find the factor of safety as per Tresca's maximum shear stress theory.
A pulley is keyed to a shaft midway between two anti-friction bearings. The bending moment at the pulley varies from – 170 N-m to + 510 N-m.The shaft is made of cold drawn steel having an ultimate strength of 540 MPa and yield strength of 400 MPa, Take σe = 0.5 σu. Determine the required diameter for an indefinite life based on Goodman equation. The actual stress concentration factor for the keyway is 1.6. The factor of safety is 1.5. Take size factor = 0.85 and surface finish factor = 0.88.
There is a gap c = 1mm between the rods in the picture, the temperature changes evenly quantitatively ΔT = 1.9°C. Calculate the normal force on the cross section of the rods. E1 = 200 GPa, L = 1.0 m, E2 = 80 GPa, A1 = 5000 mm2, A2 = 2000 mm2, α1 = 12*10-61/°C, α2 = 8*10-61/°C