07 Consider two identical bars of length 1 and mass m is pinned together at a point, as shown in the Figure. Support A is a fixed pin-joint. The other support B is also a pin-joint, but free to move horizontally. To keep the system in equilibrium, a force F is applied, as shown in the Figure. Find the force F using the principle of virtual work.. 3127

07 Consider two identical bars of length 1 and mass m is pinned together at a point, as shown in the Figure. Support A is a fixed pin-joint. The other support B is also a pin-joint, but free to move horizontally. To keep the system in equilibrium, a force F is applied, as shown in the Figure. Find the force F using the principle of virtual work.. 3127

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.14P: A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae=...

See similar textbooks

Similar questions

-11 A rubber cube R of a side L = 3 in. and cross- sectional area A = 9 in2 is compressed inside a steel cube S by a force F = 5 lb that applies uniformly distributed pressure to the rubber. Assume E 0.3ksi and,, = 0.45. (a) Calculate the lateral pressure between the rubber and steel (disregard friction between the rubber and the steel, and assume that the steel block is rigid when compared to the rubber). (b) Calculate the change in volume of the rubber.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
PROBLEM: Determine the forces in each member using any methoddiscussed in your theory of structures/mechanics. Using Software is notallowed. Show complete solution and tabulate your answers indicatingwhether it is compression or tension. Use Pn = 205 kN, Po = Zero. a) From the Problem and the image , Design one tension member, use either a double angle of a wt section. Check its adequacy using 1 line of bolts (three bolts in a line spaced at 75mm on centers) Assume a bolt diameter from 16-22mm. Use A 36 for all steel. Neglect block shear.
The simplest truss consists of two rods and is loaded by the force F. Given: F = 5,1 kN. Angle α = 69 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
A 2.3 m long stick with a uniform mass distribution extends horizontally from abuilding. There are two wires attached to the stick, wire A is attached to the beam 3/5 of theway from the building to the end of the stick, it pulls up at a 63° angle to the stick; wire B isattached 1/6 of the way from the building to the end of the stick, and pulls it down at a 32° angle to the stick.The tension in cable a is 112 N. What is the tension on wire B?
the bent bar AB weighing 10lb/ft is mounted as shown in figure 2 upon a carriage weighing 250 lb. The center of gravity of the carriage is at C midway between the wheels. If P=108lb and there is no frictional resistance at the wheels, find the wheel reaction R1. find the vertical component of the hinge force at A. find the horizontal concept of the hinge force at A.
A truck of mass 3 tonnes runs into a buffer stop having three buffer springs each of 40 kN/cm stiffness connected in parallel. Find the maximum compression of the springs, and the load if the wagon is travelling at 60 kmph. 1-Equivalent Stiffness of spring in kN/mm is 2-Kinetic Energy in kNmm is 3-The maximum compression of the spring in mm is 4-Load acting on the spring in kN is
A truck of mass 1 tonnes runs into a buffer stop having three buffer springs each of 15 kN/cm stiffness connected in parallel. Find the maximum compression of the springs, and the load if the wagon is travelling at 110 kmph. Equivalent Stiffness of spring in kN/mm is Kinetic Energy in kNmm The maximum compression of the spring in mm Load acting on the spring in kN is
A truck of mass 2 tonnes runs into a buffer stop having three buffer springs each of 10 kN/cm stiffness connected in parallel. Find the maximum compression of the springs, and the load if the wagon is travelling at 110 kmph.
nonuniform beam 4.50 m long and weighing 1.40 kNmakes an angle of 25.0° below the horizontal. It is held in position bya frictionless pivot at its upper right end and by a cable 3.00 m fartherdown the beam and perpendicular to it . The center ofgravity of the beam is 2.00 m down the beam from the pivot. Lightingequipment exerts a 5.00 kN downward force on the lower left end ofthe beam. Find the tension T in the cable and the horizontal and verticalcomponents of the force exerted on the beam by the pivot. Start bysketching a free-body diagram of the beam.
A horizontal board weighing Wb = 600 N is hinged to a vertical wall. A personweighing Wp = 400 N stands at the end of the board 5 m from the wall. A rope is attached to theboard at a point 3 m from the wall and makes an angle of θ = 40° with theboard. Determine the tension (T) in the rope
Two weights are connectedby a very light, flexible cord that passesover an 80.0 N frictionless pulley of radius0.300 m. The pulley is a solid uniformdisk and is supported by a hookconnected to the ceiling (Fig.).What force does the ceiling exert on thehook?