At the same construction site, a junior engineer approached you for advice. The engineer showed you a Free Body Diagram of a bolt lifting two heavy materials, F1 and F2 as shown in Figure 2. You observed a mistake in her calculation which could break the bolt. Given that she has already calculated the resultant magnitude of FR = 5ON and its direction 8, = 110°, B, = 80°; (a) Calculate the magnitude of the force F2. (b) Calculate the coordinate direction angles (8,, 8y, 02) for F2. N-

At the same construction site, a junior engineer approached you for advice. The engineer showed you a Free Body Diagram of a bolt lifting two heavy materials, F1 and F2 as shown in Figure 2. You observed a mistake in her calculation which could break the bolt. Given that she has already calculated the resultant magnitude of FR = 5ON and its direction 8, = 110°, B, = 80°; (a) Calculate the magnitude of the force F2. (b) Calculate the coordinate direction angles (8,, 8y, 02) for F2. N-

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter4: Mechanical Processes

Section: Chapter Questions

Problem 4.21P

See similar textbooks

Similar questions

Engineering Mechanics (Like/Thumbs-up will be given. Write the solutions&FBD legibly. Include negative sign if in Compression, ex. -1,500 or if in Tension, ex. 1,500. Round to the nearest whole number.) The bucket and its load have a combined weight of 4000 lb with center of gravity at G. You may neglect the effect of the weights of the other members. Determine: A. Force in the hydraulic cylinder AB, in lb B. Magnitude of the pin reaction at O, in lb round off to two (2) decimal places
Mr. Pine lives on the 13th floor of the Xcel building in Denver. He has decided to extend his existing d1 ft deck (d1 = 3 ft) and add a swimming pool. To get approval for his pool, Mr. Pine must provide information to the building manager. He has hired you to provide: (1) the resultant of the distributed load f(x) lb (2) where the resultant acts relative to point A (3) the reactions at point A due to the addition (distributed load) Given: d2 = 33 ft and f(?) = 215x2 + 3749 lb with x measured from point A
A wire 4m long is stretched horizontally between points A and B 4m apart. A load W placed at the center of the wire produces a sag of 53.4mm,a. If the wire is 25mm2in cross-section and the Young’s modulus is 200GPa, what is the magnitude of load W?b. If the load was reduced by 40%, what will be the sag?
What is the bending moment from the controlling ASD load combination with dead load moment MD=5,000 lb-in and live load moment ML=10,000 lb-in? (units=lb-in) 15,000 10,000 5,000 22,000
The hanger for each chandelier in the grand ballroom of a five – star hotel is composed of a 2 m diameter ring weighing 2.5 kN/m and is supported by 6 rods such that said ring will be 3 m below the ceiling support. Find the tension in each rod.a. 1.72 kN c. 2.76 kNb. 3.38 kN d. 2.62 kN What is the minimum required diameter of each rod without exceeding the allowable stress 124 MPa?a. 5.32 mm c. 6.70 mmb. 4.41 mm d. 3.09 mm Which of the following most nearly gives the vertical displacement of the ring if the diameter of each cable is 10 mm?a. 0.53 mm c. 0.59 mmb. 0.67 mm d. 0.64 mm
A 10-lb force is pushing the 40-lb block as shown. The incline angle of the plane is α=40º . The coefficient of static friction between the block and the incline is μs = 0.75 and the coefficient of kinetic friction is μk = 0.65. Will the block slide on the plane? If it does, will it slide up or down the plane? What is the friction force between the block and the plane?
A structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries a tensile load of 29k;E=29 xx10^(3)ksi. a. Find the total elongation delta of the rod. b. What diameter d is necessary if the total delta is limited to 0.1 inch?
Imagine the plumb bob as a perfect cone, compute for the volume of steel needed to make thecone if the dimension are a diameter of 60 mm and a height of 40 mm.The height of a cone shaped tank for liquid storage in a chemical factory is 9 ft with a diameter of14 ft. a) what is the volume of liquid the tank can hold in cubic feet? (5 pts); b) if the storage tankreleases water with a rate of 350 liters per minute, how many minutes will it take for the tank beemptied?
A pull of 6,500 lb is applied to a steel rod which has an ultimate stressof 65,000 psi. Determine the steel rod diameter if the factor of safetyis 5.A. 0.998 inch C. 0.798 inchB. 0.598 inch D. 0.398 inch
For the distributed loads shown (System 1).a) Reduce the distributed loads to three concentrated forces and specify where each force acts along the beam (System 2).b) Reduce the system to an equivalent force and moment at A (System 3).c) How do we know that the simplest resultant exists?d) Draw the simplest resultant (a single force that produces the same moment about A).Note: Draw and label each system.
STRENGHT OF MATERIALS (Please write the solutions correctly and legibly. No long explanation needed. Answer in 3 decimal places. Rate will be given. 15 minutes left :<) Write the shear and moment equations for the beam loaded as shown and sketch the shear and moment diagrams. Indicate all values at the change of load points. Use a ruler for the stright line part/s of the diagrams.
If FFF = 7.8 kNkN , determine the magnitude of the resultant force acting on the screw eye.(Figure 1) Express your answer to three significant figures and include the appropriate units. Determine the direction of the resultant force acting on the screw eye measured clockwise from the xx axis. Express your answer to three significant figures and include the appropriate units.