At what depth below the surface of the oil, relative density 0.89 will produce a pressure of 130 kN/m2. What depth of water is this equivalent to? Depth of oil in meters Depth of water is this equivalent to

At what depth below the surface of the oil, relative density 0.89 will produce a pressure of 130 kN/m2. What depth of water is this equivalent to? Depth of oil in meters Depth of water is this equivalent to

Name: 9:21Expert Q&ADoneAt what depth below the surface ofthe oil, relative
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 9:21Expert Q&ADoneAt what depth below the surface ofthe oil, relative density 0.89 willproduce a pressure of 130 kN/m2.What depth of water is this equivalentto?Depth of oil in metersDepth of water is this equivalent to

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

The greatest known ocean depth is the Mariana Trench, in the Pacific Ocean, which is at 11,034 m. At this depth the specific gravity of seawater is approximately 10,520 N / m3. On the surface ρg P 10,050 N / m3. Estimate the pressure at this depth in atmosphere
The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution.
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses RI and R2. determine its value for water if (G. = 0.072 N/m, RI=30mm, & R2=36mm) (Take smooth and very clean glass tubes).
The Mayflower ship having a displacement of 27000 metric tons and a draft of 10.4 m in ocean (sp. gr. = 1.03) enters in the Legazpi International Port with a specific gravity of 1.0 (seawater). If Mayflower’s horizontal section of the ship at the waterline is 3000 m2, what depth of seawater is required to float the ship? a. 10.63 m b. 10.58 m c. 10.66 m d. 10.54 m
Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm.
The cylindrical water tank in Fig. is being fi lled ata volume fl ow Q 1 = 1.0 gal/min, while the water alsodrains from a bottom hole of diameter d = 6 mm. At timet = 0, h = 0. Find and plot the variation h ( t ) and the eventualmaximum water depth h max . Assume that Bernoulli’ssteady-fl ow equation is valid.
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
Capillary rise in the glass tube used for measuring water level isnot to exceed 0.5 mm. Determine its minimum size, given thatsurface tension for water in contact with air = 0.07112 N/m.
Estimate the capillary depression for mercury in a glass capillary tube 2 mm in diameter. Use surface tension = 0.514 N/m Ans. 5.9 mm
[Fluid dynamics] a.) For your science exhibit, you want to make a block of wood float at the interface between a layer of oil of unknown density ?_???, and water (?_????? = 1000 [kg/m^3]) inside a container as shown. What must be the density of the oil so that only 30.0% of the wood is submerged in water? b.) Water is flowing through a pipeline shown onthe right. The radii of the pipe at points 1 and 2 are0.500 [m] and 1.50 [m], respectively. The volume flowrate through the pipeline is 2.50 [L/s]. If the pressureat point 1 in the pipe is 200 [kPa], what is the pressureat point 2, located 5.00 [m] above point 1?
A fi sh tank 14 in deep by 16 by 27 in is to be carried in acar that may experience accelerations as high as 6 m/s 2 .What is the maximum water depth that will avoid spillingin rigid-body motion? What is the proper alignment of thetank with respect to the car motion?