At what flow rate might turbulence begin to develop in a 0.380 m diameter water main? Assume a 20°C temperature and a Reynolds number of 2000. (Use 1.005 x 10-3 (N/m2) · s for the viscosity of water.) m3/s

At what flow rate might turbulence begin to develop in a 0.380 m diameter water main? Assume a 20°C temperature and a Reynolds number of 2000. (Use 1.005 x 10-3 (N/m2) · s for the viscosity of water.) m3/s

Name: At what flow rate might turbulence begin to develop in a 0.380 m diam
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: At what flow rate might turbulence begin to develop in a 0.380 m diameter water main? Assume a 20°C temperature and aReynolds number of 2000. (Use 1.005 × 10-3 (N/m²) · s for the viscosity of water.)m3/sAdditional MaterialsO Reading

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 102P: A fire hose has an inside diameter of 6.40 cm. Suppose such a hose caries a flow of 40.0 L/s...

See similar textbooks

Similar questions

Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
What is the average flow rate in cm3/s of gasoline to the engine of a car traveling at 100 km/h if it averages 10.0 km/L?
What must be the contact area between a suction cup (completely evacuated) and a ceiling if the cup is to support the weight of an 80.0-kg student?
An oil gusher shoots crude 25.0 m the through a pipe with a 0.100-m diameter. Neglecting resistance but not resistance of the pipe, and assuming laminar flow, calculate pressure at be entrance of be 50.0-m-Iong vertical pipe. Take of the oil to be 900 kg/m3 and its viscosity to be 100(N/m2) s (or 1.00 Pa s). Note that you must take into account the pressure due to 50.0-m column of oil in pipe.
Calculate Reynolds numbers for flow of trough (a) a nozzle a radius of 0.250 cm and (b) a garden hose with a radius of 0.900 cm, when be nozzle is attached to hose. The flow rate through hose and nozzle is 0.500 L/s. Can flow in either possibly be laminar?
Suppose you have a wind speed gauge like the pitot tube shown in Figure 14.32. By what factor must wad speed increase to double the value of h in the manometer? Is independent of be moving fluid and be fluid the Figure 14.32 Measurement of fluid speed on Bernoulli’s principle. (a) A manometer is connected to two tubes close together and small enough not to disturb the flow. Tube 1 is open at the end facing the flow. A dead spot having zero speed is created there. Tube 2 has an opening on the side, so the fluid has a speed v across; thus, pressure there drops. The difference in pressure at the manometer is 12v22 , so h is proportional to . 12v22 (b) This type of velocity measuring device is a Prandtl tube, also known as a pitot tube.
A trash compactor can compress its contents to 0.350 times their original volume. Neglecting mass of air expelled, by what factor is the density of be rubbish increased?
Gasoline is piped underground from refineries to major users. The flow rate is 3.00102m3/s (about 500 gal/min), viscosity of gasoline is 3.00102m3/s , and its density is 680 kg/m3. (a) What minimum diameter must be pipe have if the Reynolds number is to be less 2000? (b) What pressure difference must be along each kilometer of be pipe to maintain flow rate?
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.
Using the equation of the previous problem, find the viscosity of motor oil in which a steel ball of radius 0.8 mm falls a terminal speed of 4.32 cm/s. The densities of the ball and the oil are 7.86 and 0.88 g/mL, respectively.
What is the pressure drop due to the Bernoulli Effect as water goes into a 3.00-cm-diameter nozzle from a 9.00-cm-diameter fire hose while carrying a flow of 40.0 L/s? (b) To what maximum above be nozzle can this water rise? (The actual height will be significantly smaller due to air resistance.)