At what velocity (in revolution per minute) should an open cylinder 300mm in diameter and 900mm high containing 45cm of water be rotated about its vertical axis such that the distance between the vertex of the paraboloid, which is located at the bottom of the tank, and the highest point on the new water surface is 90cm? Round off your answer to a whole number.

At what velocity (in revolution per minute) should an open cylinder 300mm in diameter and 900mm high containing 45cm of water be rotated about its vertical axis such that the distance between the vertex of the paraboloid, which is located at the bottom of the tank, and the highest point on the new water surface is 90cm? Round off your answer to a whole number.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 45P

See similar textbooks

Similar questions

An open cylindrical tank having a radius of 0.45 m. is filled with water at a depth of 0.68 m. If it is rotated about its vertical axis to a velocity of 103 rpm, what should be the height (in meters) so that no water will be spilled out? Round off to two decimal places.
A tank is in the shape of an inverted cone, having height h = 2.5 m and base radius r = 0.75 m. If water is poured into the tank at a rate of 15 L/s, how long will it take to fill the tank? Water flows into a cubical tank at a rate of 15 L/s. If the top surface of the water in the tank is rising by 1.5 cm every second, what is the length of each side of the tank?
An open cylindrical tank 2 meters in diameter and 4 meters tall is half – full of water. The tank is rotated about its vertical axis at constant angular speed. How much water is spilled (in liters) if the angular speed is 90 rpm?
A plunger (54 mm Ø and 0.5 m long) is moving through a horizontal cylinder (60 mm Ø) containing oil at a speed of 8 m/sec that has a viscosity of 7.1x10-6 m2/sec and specific gravity of 0.84. Calculate the force needed to maintain its velocity. Use 2 decimal places.
An open cylindrical vessel 1.3 m in diameter and 2.1 m high is 2/3 full of water. If rotated about the vertical axis at a constant angular speed of 100 rpm. What is the amount of water that will be spilled out? What should be the height of the tank so that no water will be spilled out?
Calculate the diameter of a pipe that would carry 75.0 ft/s of a liquid at an average velocity of 10.0 ft/s.
A spherical ball with radius of 10cm is full of water. If the water from the spherical ball is poured onto a cylindrical glass, what is the height of the top surface of the water from the bottom of the glass if the glass has a radius of 3 cm?
Suppose that one such tank is cylinder shaped, 50ft high with a radius of 20ft. If we assume that water is pumped out of the tank via a pipe directly on top of the tank and that the tank is filled to a depth of 30ft, how much work (in ft-lbs) would be done by a pump to empty the tank? You may take the density of water to be 62.4 lbs/ft3
A rectangular tank is 6 meters long, 1.2 meters ide and 2.4 meters deep is completely open at the top. If its initially filled to the top, how much liquid will be spilled out if it is given a horizontal acceleration of 0.3 grams in the direction of its length?
Calculate the diameter of a pipe that must carry 140 L/min at a velocity of 5 m/s *.
Water flows through a pipe 25 mm in diameter at a velocity of 6 m/s. Determine whether the flow will be laminar or turbulent assuming that the dynamic viscosity of water is taken as1.30 × 10−3 kg/ms and its mass density as 1000 kg/m3. If oil of specific gravity 0.9 and dynamic viscosity 9.6 × 10−2 kg/ms is pumped through the same pipe, what type of flow will occur?
A cylindrical tank 1m in diameter and 3m tall weighs 3.86kN. Given: ylead = 100kN/m3. Which of the following most nearly gives the weight of the lead that must be placed inside the tank to make the tank float vertically with 2.50m submerged in water?