Q16/ The value of the normal stress due to axial force 2 kN applied on the * :beam is Point D 10 kN Point E 50 mm h-200 mm 2 kN 75 mm 2m 3m Point F b-100 mm Q17/ The value of the normal stress due to flexural force 10 kN applied on * :the beam at point D is Point D 10 kN Point E h-200 mm 50 mm 2 kN 75 mm 2m 3m Point F b-100 mm due to flexural force 10 kN applied on * :the beam at point E is Point D 10 kN Point E 50 mm h-200 mm 2 kN 75 mm 2m 3m Point F b-100 mm

Q16/ The value of the normal stress due to axial force 2 kN applied on the * :beam is Point D 10 kN Point E 50 mm h-200 mm 2 kN 75 mm 2m 3m Point F b-100 mm Q17/ The value of the normal stress due to flexural force 10 kN applied on * :the beam at point D is Point D 10 kN Point E h-200 mm 50 mm 2 kN 75 mm 2m 3m Point F b-100 mm due to flexural force 10 kN applied on * :the beam at point E is Point D 10 kN Point E 50 mm h-200 mm 2 kN 75 mm 2m 3m Point F b-100 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

a) The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion) i) The second moment of area relative to z-axis, I_z, for the cross-section can be calculated as ( Enter your answer in cm4 ii) The bending stress at Point H can be calculated as (Enter your answer in MPa, Compressive stress is negative and tensile stress is positive) iii) The first moment of area required to calculate shear stress at H can be calculated as (Enter your answer in mm^3) iv) The absolute value of the transverse shear stress at point H can be calculated as (Enter your answer in MPa ) v) Maximum principal stress can be calculated as (Enter your answer in MPa ) vi) Minimum principal stress can be calculated as (Enter your answer in MPa ) vii) The equivalent stress for Maximum-Shear-Stress Theory ( Tresca criterion) (Enter your answer in MPa ) b) The von Mises equivalent stresses at point H can be calculated as: MPa c) The factors of safety at point H…
circular cross-section belt pulley system supported by two bearings tensioning forces formed in belts in Shaft power transmission T11 = 8 kN, T12 = 2 kN, T21 = 8 kN and T22 = 2 kN. Pulley weights are 1 no.lu pulley for both pulleys W =6 kN. Each two pulley diameters d = 1,2 m dir. a = 0.2 m ve b = c = 0,4 m. Slip safety stress Jul = 70 MPa a-) Greatest shear stress (TRESCA) b-) The diameter of the shaft (d) according to the largest change in shape (VON MISES) criteriayou can find.
A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is 6.1359 x 10 -7 m4 , determine the maximum torque the shaft could handle. A. 1.23 KN.m B. 1.68 KN.m C. 1.84 KN.m D. 2.48 KN.m
Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure of 9 MPa. The average circumferential (hoop) stress in MPa isa) 150 MPA b ) 125 MPa c) 175 MPa d ) 200 MPa e) none of these
A compound shaft consists of two segments. Segment (1) is a solid bronze [G = 45 GPa] shaft with an outside diameter of 80 mm, a length L1 = 780 mm, and allowable shear stress of 65 MPa. Segment (2) is a solid aluminum alloy [G = 26 GPa ksi] shaft with an outside diameter of 95 mm, a length L2 = 620 mm, and allowable shear stress of 40 MPa. The maximum rotation angle at the free end of the compound shaft must be limited to φA ≤ 2.5°. Determine the magnitude of the largest torque TA that may be applied at A.
The torque transmitted by a solid shaft of diameter 10 mm and shear stress 75 MPa Select one: a. 14.72x109 N-m b. 14.72 kN-m c. 147.2 N-mm d. 14.72 N-m
4kN/m uniform spring load h = 2b allowable normal stress 12MPa h(min) = ?
In determining the bending stress, what conclusion can be drawn if the neutral axis is an axis of symmetric of the cross-section? a. The maximum tensile and compression bending stresses are equal in magnitude and occur at the section of the largest bending moment. b. The maximum tensile and compression bending stresses are equal in magnitude and occur at the section of the smallest bending moment. c. None of the choices d. The maximum tensile and compressive bending stresses may occur in different sections.
The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m2. What will be the stress along the face AB? (Cambridge) ANSWER: 17.68 kN; 11.8 MN/m2 compressive.
A solid shaft is subjected to a twisting moment of 350 kNm. If the angle of twist is 5° per meter of the shaft and the shear stress is not to exceed 350 MPa. Determine the suitable shaft diameter by comparing the strength design and rigidity design. Also, determine the maximum shear strain acting on the shaft. Take G =225 GPa.
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
Given:a. the force in BD=25KNb. vertical reaction at point C=-10KNc. horizontal reaction at point C=15KNd. resultant of reaction at point C=18.0KNe. allowable tensile (normal) stress in member BD =83.33MPaf. the allowable shear stress in the pin at C =72.7MPaPlease help me solve for:1. What is the required cross-section area and minimum thickness t of member BD?2. What is the required SHEAR cross-section area at point C?3. What is the minimum diameter for the pin at C?(Solve for a value with the combination of mm and N)