AWshape is to be used for a uniformly loaded simple beamcarrying a total dead load of 26 kips and a total live load of 26 kips on a36-ft span. Select the lightest weight shape for unbraced lengths of (1) 9 ft,(2) 12 ft, and (3) 18 ft.

AWshape is to be used for a uniformly loaded simple beamcarrying a total dead load of 26 kips and a total live load of 26 kips on a36-ft span. Select the lightest weight shape for unbraced lengths of (1) 9 ft,(2) 12 ft, and (3) 18 ft.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.10.7P

See similar textbooks

Related questions

Q: A W 5300*101 of Steel Section (fy= 345 MPa & fu= 450 MPa) is used as simply supported beamwith a…

A: Properties of W530×101 From AISC manual Table 3-2 Sx=2290×103 mm3, Zx=2620×102 mm3Lb=3 m, L=15 m,…

Q: A reinforced concrete simply supported beam has a span of 32’ and supports service dead load of 1050…

Q: For the given beam shown in Figure 1 with fe= 35 MPa, f= 400 MPa, ag = 20 mm it is required to: a)…

A: Given fc’= 35 MPa, fy = 400 MPa, ag = 20 mm, axial tension =…

Q: A beam section shown below will be subjected to a maximum service dead load of 215 KN.m. Determine…

A: Given: D.L = 2.15KN/M f'c = 21 Mpa fy = 415 Mpa 5bars of 25mm Size = 360*650mm 1.Calculation of Area…

Q: A beam must be designed to the following specifications: ●● Span length = 35 ft ●● Beam spacing = 10…

A: We will assume the following data, b(breath)=250mm d (depth) =550mm d' (cover) = 50mm

Q: A single span beam is simply supported between two columns and carries a reinforced concrete slab as…

A: The span of simply supported beam if 6m. UDL on the beam if 13.7 KN/m. Steel to be used is S275. The…

Q: For the beam(550x780mm) to carried the loads shown in the figure below,design the al rainforcement…

A: Design steel reinforcement 350x 780mmm

Q: A circular column of a cross-section (460)mm in diameter is reinforced with 6 bars of ($25mm), with…

A: Axial force : The force operating on a body in its axial direction is characterized as axial tension…

Q: A reinforced concrete tied column is to be designed to support a factored axial load of 3000 kN. Use…

Q: A W530x101 is to be used as a column with an effective length of 6.00 m. Determine the allowable…

Q: A 36 ft simple span beam is to support two movable service 20 kip loads a distance of 12 ft apart.…

A: LRFD method: Load and Resistance Factor Design method is used for designing steel structures and…

Q: A simply supported beam with a span length of 45ft is laterally supported only at its ends and is…

A: For solving this question we are using the LFRD method which is Load Resistance Factor Design, which…

Q: A simply supported beam with a span length of 45 feet is laterally supported at its ends and is…

A: Solution Given Data Dead load=400 ln/ft Live load= 1000 lb/ft Span length = 45 feet

Q: A simply supported beam of span 12 m is loaded with a triangular load, maximum of 12 kN/m at the…

Q: An A36 W10 x 100 beam is to support the loads as shown. Neglecting the weight of the beam, check if…

A: From the loading, moment on the beam Mmax = 524.96 kN.m Yield stress f = 250 MPa Section modulus Sx…

Q: Select #3 U stirrups spacings for an 18-ft simple span beam of 15 in. beam width and 28 in. depth…

Q: A simple-span, uniformly loaded beam consists of a W 16 × 45 with Fy = 50 ksi. Find the percentage…

A: Solution Given data Section given = W 16 × 45 Fy = 50 ksi Properties of W 16 × 45 section For web…

Q: Use W27 x 84 as a flexural member with Fy = 50 ksi and Cb = 1.0, Use both methods, LRFD(Design…

A: Fy = 50ksi Md = moment due to dead load ML = moment due to live load [Note : moment capacity or…

Q: beam is simply supported and has a span of 12 m. The beam is a W33 x 240 with Fy = 345 MPa. Compute…

A: Given:- Properties of W33x240Weight = 3.51 kN/mA = 45,548 mm2d = 850.9 mmbf = 402.97 mmtf = 35.56…

Q: lem 1 The W21x50 steel beam shown in the figure below has its compression flange laterally braced at…

A: W21x50 steel beam FY = 50ksi

Q: concentrated load that this beam can carry besides its own weight. Use fc = 7MPA, fs = 124 MPa, n =…

Q: A W250X101 is used as a 6.1 m - long column. It is fixed at the bottom and fixed against rotation…

A: Given data: Length of column=6.1 m Section of column=W250*101 Axial dead load=378 kN Grade of…

Q: AWshape is to be used for a uniformly loaded simple beamcarrying a total dead load of 30 kips and a…

A: Consider the A36 steel section. The yield strength of the steel is fy=36 ksi. The dead load (DL) is…

Q: Find the safe axial load that a W 24 x117 column section could carry if it has a length of 8 m under…

A: Given Data: The column section is W24x117. The sectional properties are: Cross-sectional area…

Q: Calculate the required spacing of 10-mm U stirrup in a rectangular beam with b = 280 mm and d = 440…

Q: A column is subjected to unfactored dead load = 200 kips and live load = 120 kips. Both ends of the…

A: DL = Dead load = 200 kipsLL = Live load = 120 kipsFactored design loadPu = 1.2 DL + 1.6 LL= 1.2×200…

Q: Determine the safe live load that the slab could carry if it has a simple span of 3m, fc' = 21MPa,…

A: Unit weight of concrete = 23.5 kN/m3 Dead load wd=γcbh=23.510.175=4.1125kNm Effective depth:…

Q: A beam with both end fixed has a span length of 20 ft. The beam carries a concentrated ultimate Pu…

A: Schematic diagram of the given problem: Factored load = 1.6 Pu

Q: A reinforced concrete T-beam has an effective flange width of 800mm with a slab thickness of 110mm.…

A: given figure determine the depth of N.A xu=0.87fyAst0.36fckBfput the…

Q: A W360 x 134 section is used as a column with an effective length of 6 m. The column carries an…

Q: Determine the maximum service live load that the column shown can support if the live load is twice…

A: ASD ASD applies service load to structure. ASD evaluates forces and stress using linear materials…

Q: A W250X101 is used as a 6.1 m - long column. It is fixed at the bottom and fixed against rotation…

A: Pu = 1.2 (DL) + 1.6 (LL) Where ; Pu = Factored load Pu = A × fcd A = Area for W 250 X 101 = 12900…

Q: Design a slab with a simple span of 4m. The slab carries a floor live load of 6.69 kPa and a…

Q: Q1 // For cantilever beam shown in Fig. below if service live load = 72 kN/m, service dead load = 30…

Q: A rectangular beam has a width of 300 mm and an effective depth of 440 mm. It is reinforced with…

Q: The maximum deflection Δmax of a W21 x 68 with span L = 25 ft loaded with a single 80 kip service…

A: given dataW21×68length of span=25ftload=80kipswe know thatdeflection of beam when concentrated…

Q: C16. For the beam and loads given below, select the stirrup spacing assuming f,' = 3,500 psi, f, =…

A: To find stirrup spacing

Q: AWshape is to be used for a uniformly loaded simple beamcarrying a total dead load of 27 kips and a…

A: Solution: Given Data: DL=27 kipsLL=50 kips From Character @, ASCEPu=1.2 DL+1.6…

Q: AW12 × 53 shape of A992 steel is used as a column withan unbraced length of 16 ft. Compute the…

A: Expression of maximum factored load is; Pc=π2EIL2 ....1 Here, P- is the maximum factored load. E-…

Q: Example 4: Design a rectangular beam using fc' = 28MPa and fy = 420MPa. Provide compression bars if…

Q: A reinforced concrete T- beam has an effective flange width of 750mm with a slab thickness of 100mm.…

A: Formula to calculate the β1 value for any fc, in English units is β1=0.85-fc'-400010000.05>0.65…

Q: H.W: A 6 m span simply supported reinforced concrete beam, with a cross section shown in the figure…

Q: For the propped beam shown, lateral braces are provided at the supports and at the midspan. The…

A: Given:- The magnitude of the factored beam weight on the propped beam = Pu = 50 kips The section…

Q: Find lightest W14 for L = 20’ and w = 3k/ft AND concentrated loads of 6k @ 4ft o.c. E = 29,000ksi,…

A: L = 20feet E = 29,000 ksi fb = 30ksi fv = 20ksi Assuming all loads are factored load w = 3k/ft…

Q: Problem 2: Compute the design moment strength of the beam section described below if fy = 420 MPa,…

Q: A W10x45 column, fixed at the bottom and hinged at the top, is to compressive load of 89 kN dead…

A: Given, DL = 89 kN LL = 356 kN L = 10 m or 10000 mm Fy = 414 MPa

Q: A W8 x 35 steel column has an unsupported height of 8 m. Using A-36 steel with Fy =248 MPa and E =…

A: Given data Properties of W8x35:A = 6645.15 mm2IX = 52.45 x 106 mm4IY = 17.69 x 106 mm4rX= 88.9…

Q: A reinforced concrete T- beam has an effective flange width of 750mm with a slab thickness of 100mm.…

A: Reinforced concrete T-beam Effective flange width, bf=750 mm Slab thickness, Df=100 mm Effective…

Q: 1. For a simply supported 610UB125 section under axial compression of span 4.5m, what is the member…

A: step 1-

Q: Determine the critical buckling stress and critical buc

A: The section W14X109 is given with Lx=20' and Ly=12' Calculating the critical buckling stress and…

Concept explainers

Introduction to Steel Design

The area of steel design is majorly concerned with the structural engineering domain, which is a specialization of civil engineering. Steel design is often known as structural steel design, whose primary concern is to design steel structures. The primary structure involves the designing and construction of frames using structural steel as the material. Residential buildings, houses, bridges, complexes, tall buildings, industrial warehouses, aircraft frames, frames of ships, and stadiums are some of the examples of structures that use steel framing.

Question

AWshape is to be used for a uniformly loaded simple beam
carrying a total dead load of 26 kips and a total live load of 26 kips on a
36-ft span. Select the lightest weight shape for unbraced lengths of (1) 9 ft,
(2) 12 ft, and (3) 18 ft.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An A36 W14X605 simply supported steel beam with span L=12.6m carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported all throughout its span. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). Calculate the maximum service PLL that the beam can carry based on flexure requirement using LRFD? Express your answer in KN in 2 decimal places.
A W12x65 is to be used as a simply supported beam on a span of 20 ft with lateral support at the ends only. The beam is required to support a plastered ceiling. If the dead load is 0.20kips/ft (including beam weight), what is the maximum uniform service live load permitted on the beam, using A992 steel? What percentage increase in live load can be gained if the beam is A572 Grade 65 steel. Use AISC 360-16 specifications
The cantilever beam shown is aW10 × 77 of A992 steel. There is no lateral supportother than at the fixed end. Use an unbracedlength equal to the span length and determinewhether the beam is adequate. The uniform load isa service dead load that includes the beam weight,and the concentrated load is a service live load.
An A36 W14X605 simply supported steel beam with span L=14.4m carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). Calculate the maximum service PLL that the beam can carry based on flexure requirement using LRFD? Express your answer in KN in 2 decimal places.
57 : Design a T-beam having cross section shown in figure below according to ACI code requirement. The beam is simply supported on span 1914 of (7.31m), The is subjected to service dead load (48.80 kN/mm) (including self-weight), and service live load (25 kN.m), Assume the designer intends dnes to use: fe-21 MPa, fy=414 MPa and bf= 1 m. Use two layer of reinforcement) at lan COSM 0.09mm RÝM OC ¹0.3 m² 1000 -0.55 m
An A36 W14X605 simply supported steel beam with span L=13.7m carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). Calculate the maximum service PLL that the beam can carry based on deflection requirement? Use deflection limit of L/240. Express your answer in KN in 2 decimal places.
A W14x90 is used as a simply supported, uniformly loaded beam with a span length of 40 feet and continuous lateral support. The yield stress, Fy, is 50 ksi. If the ratio of live load to dead load is 2.5, compute the available strength and determine the maximum total service load, in kips/ft, that can be supported. (Hint: This is not a compact shape!)
steel: Select the lightest W-shape steel beam (Fy 50 ksi) to carry an ultimate uniformly distributed load of 6 k/ft over a span of 24 ti as shown in the figure below. The beam is laterally supported at its ends only. Checking of compactness, self-weight, and deflection are not needed. Start your solution with a zero self-weight. Use the.method LRFD 6 k/ft 24 ft
A W310 x97 steel wide-flange section Supports a uniformly distributed line load on a simple span of 7 m. Assume A36 steel. Calculate the allowable load (kN/m). Neglect the weight of the beam. Use Fv=0.4 Fy Material Steel ASTM A36 or A501 Steel (high-strength low-alloy) ASTM A992 Steel AISI 1020 hot-rolled Steel AISI 1040 hot-rolled Stainless steel (annealed) Cast iron (gray) Aluminum alloy 6061-T6 Magnesium alloy Titanium alloy Brass (rolled) Bronze (cast) Copper (hard drawn) Concrete Density kg/m³ x 10³ 7.85 7.85 7.85 7.85 7.85 7.21 2.64 1.794 4.40 8.56 8.56 8.81 2.40 Mod. of Mod. of Elasticity E MPa Rigidity G MPa x 10³ x 10³ 207 83 207 207 207 200 103. 70 45 114 97 83 103 21.5 83 79.3 79.3 80 41 28 17 45 41 34 41 Tensile Yield Strength F, MPa 250 345 210 290 280 240 210 900 340 170 280 Ultimate Strength MPa Tens. Comp. 400 450 380 520 580 140 260 280 970 410 230 380 550 390 21 Shear Coeff. of Thermal Expansion m/m/c x 10-6 260 11.7 11.7 11.7 Poisson's Ratio μ 0.25 9.9 0.25 11.7 0.25…
A W24x250 is used as a beam to support a one-way concrete slab floor system. The floor is to carry a totalload of Y kPa (30% DL, 70%LL, self-weight is included in DL). The beam is simply supported over a span ofW/2 m. Assume the beam is laterally supported over its length. Use Fy = 248 MPa. Allowable deflectionfrom service loads is L/360. Use ASD. a.What is the center-to-center spacing of the beams (m) based on shear capacity? b.What is the center-to-center spacing of the beams (m) based on flexural capacity?C.What is the center-to-center spacing of the beams (m) based on allowable deflection? Reference datas: W= 25 mm , 25 MPaW/2 = 12.5 mW/4 =6.25mX=475 KNY= 155 KN, 155 KPa, 175 mmZ=60×+Z=535mm
1.) In the H20-44 truck loading, the 44 means?CHOICES: a.) Total weight of truck in ksi b.) Total weight of truck in Ton c.) year of introduction d.) Total weight of truck in metric ton 2.) The Muller Breslau principle is applicable toCHOICES: a.) Beams only b.) Beams, Trusses and Frames c.) Trusses and Frames only d.) Beams and Trusses only Thank yoouu!!
A simply supported beam with a span length of 45 feet is laterally supported at its ends and is subjected to the following service loads: Dead load=400 lbyft (including the weight of the beam) Live load = 1000 lbyft If Fy=50 ksi, is a W14x 90 adequate?