A Y-connected three-phase induction motorhas the following values printed on thenameplate: 230V line voltage, 60HZ, 6-pole.Additionally, it has the following parametersin ohms/phase as referred to the stator:R1=0.5 Q, R2'=0.252, X1=0.75, X2'= 0.52,Rc=5002, and Xm-1002. The friction andwindage loss is 150W. At a rated slip of 2.5%,determine:(a) The input power (b) The statorCu-loss, (c) The rotor Cu-loss (d) The air-gap power (e) The shaft torque (g) efficiency

Answered: Image /qna-images/answer/35bbff46-1f0a-4ccc-9588-1718e8eb5747.jpg

AY-connected three-phase induction motor has the following values printed on the nameplate: 23OV line voltage, 60HZ, 6-pole. Additionally, it has the following parameters in ohms/phase as referred to the stator: R1=0.5 Q, R2'=0.25Q, X1=0.75, X2'= 0.52, Rc=5002, and Xm=1002. The friction and windage loss is 150W. At a rated slip of 2.5%, determine:(a) The input power (b) The stator Cu-loss, (c) The rotor Cu-loss (d) The air- gap power (e) The shaft torque (g) efficiency

AY-connected three-phase induction motor has the following values printed on the nameplate: 23OV line voltage, 60HZ, 6-pole. Additionally, it has the following parameters in ohms/phase as referred to the stator: R1=0.5 Q, R2'=0.25Q, X1=0.75, X2'= 0.52, Rc=5002, and Xm=1002. The friction and windage loss is 150W. At a rated slip of 2.5%, determine:(a) The input power (b) The stator Cu-loss, (c) The rotor Cu-loss (d) The air- gap power (e) The shaft torque (g) efficiency

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

- Reconnecting Induction Motors 6.a. The voltage in a 460-volt motor is changed to 425 volts. If the original torque was 125 lb-ft, the newtorque isA. 135 lb-ft.B. 117 lb-ft.C. 115 lb-ft.D. 107 lb-ft.6.b. If a 575-volt three-phase motor originally connected in 3-parallel △ is reconnected in 5-parallel Y, thenew voltage isA. 501 volts.B. 794 volts.C. 598 volts.D. 747 volts.
1.Show that if three phase currents, each of equal magnitude and differing in phase by 120degree, flow in a three phase winding that are 120 degree apart from each other then it willproduce a rotating magnetic field of a fixed magnitude. 2. A three phase, 5-hp, 60Hz, 115V, 4-pole induction motor is operating at rated voltage, rated frequency, and 125 percent rated load has an efficiency of 85.4 percent. The stator conductor loss, rotor copper loss and core loss are 223.2W, 153W, and 114.8W respectively.Sketch the power flow diagram, enter the given data, and determine i) shaft speed ii) shaft torque 3. Can single phase induction motor be self-started? Explain the operation of a split phase single phase induction motor?
A three-phase, 415V, 50Hz, six-pole, star-connected induction motor is driven from a variable voltage, variable frequency supply. The motor circuit phase parameters are as follows: R₁ = R' = 1.002, X₂=X₂ = 2.002, Xm=502 When running at full load on rated voltage and frequency, the motor takes a line current of 12A at 0.86 power factor lagging. Assuming that the motor is operating in the constant flux mode, determine the supply voltage and speed when delivering the same torque at 60Hz.
A 200V, 3, star connected induction motor takes 30A at a line voltage of 35V with rotor locked. With this line voltage, power input to motor is 450W and core loss is 60W.The dc resistance between a pair of stator terminals is 0.15Ω. If the ratio of ac to dc resistance is 1.6, find the equivalent leakage reactance/phase of the motor and the stator and rotor resistance per phase.
3-phase, star-connected, 220 V line to line, 50-Hz, 4-pole induction motor has the following constants in ohm per phase referred to stator. r1 = 0.29, r2 = 0.14, X1 = 0.5, X2 = 0.21 and magnetizing reactance X0 = 13.25 ohms .The total friction windage and core lose may be assumed to be a constant at 400 watts. For a slip of 2 percent calculate: a.)Speed b.)Output, and c.) Stator current of the motor
(b) A 415V, 50Hz, delta-connected, 4-pole, squirrel cage induction motor has a perphase equivalent circuit as shown in Figure Q4(b). The circuit parameter values (in Ω/phase) for the stator is as follows: R1 = 0.095 Ω ; R2 = 0.06 Ω; X1 = 0.68 Ω ; X2 = 0.67 Ω; Xm = 18 Ω The motor is running at 1400 rpm at full-load. The core loss of the motor is assumed to be zero. The total friction and windage losses is 600 W, independent of load. Determine the efficiency of the motor.
The following data are obtained for 7.5 hp, 28A, 4-pole, 208V, 60Hz, Y-connected stator squirrel cage three-phase induction motor. DC Test: Voc = 13.6V , Ioc= 28A No-Load Test: Vt= 208V , IA= 8.12A , Pout= 420W Locked-Rolot Test: Vt=25V , IA= 28A , Pin = 920W Calculate the per-phase equivalent circuit parumeters of this motor referred to the stator side. ?????
Draw the circle diagram for a 5.6 kW, 400-V, 3-φ, 4-pole, 50-Hz, slip-ring induction motor from the following data : No-load readings : 400 V, 6 A, cos φ0 = 0.087 : Short-circuit test : 100 V, 12 A, 720 W. The ratio of primary to secondary turns = 2.62, stator resistance per phase is 0.67 Ω and of the rotor is 0.185 Ω. Calculate (i) full-load current (ii) full-load slip (iii) full-load power factor (iv) maximum torque full - load torque (v) maximum power.
A three phase, 4 pole, 3300 V, 50 Hz, star connected Induction motor, has identical primary and referred secondary impedance of value 3+j9 Ohm per phase. Using the approximate circuit, calculate: A. The full load torque at rated slip of 5%. B. The maximum torque at normal voltage and frequency.
A 110-V, 50-Hz single phase induction motor (split -phase) has the following constants for the main and auxiliary windings: Main winding, Zm (1.2 +j 25) ohm and auxiliary winding, Z,= (12+j 5) ohm. Determine (i) total current and power factor currents at time of starting, and (ii) phase angle between the main winding current and starting winding current.
Draw the circle diagram for a 5.6 kW, 400-V, 3-φ, 4-pole, 50-Hz, slip-ring induction motor from the following data :No-load readings : 400 V, 6 A, cos φ0 = 0.087 : Short-circuit test : 100 V, 12 A, 720 W.The ratio of primary to secondary turns = 2.62, stator resistance per phase is 0.67 Ωand of the rotor is 0.185 Ω.
Please Do not Designed 15 Kw Please Must Show Given Questions in Design for 11KW Motor . A15 kW, 440 V, 4-pole, 50 Hz, 3-phase induction motor is built with a stator bore 0.25 m and a core length of 0.16. The specific electric loading is 23000 ampere conductors/meter. Using the data of this machine, determine the core dimensions, number of stator slots and number of stator conductors for 11 kW, 460 V, 6 pole, 50 Hz motor. Assume a full-load efficiency of 84% and power factor of 0.82 for each machine.the Winding Factor is 0.955.