B 450 lb-ft 350 lb-ft 600 lb-ft

Q: If the applied torque on shaft CD is 82.5 N-m, determine the absolute maximum shear stress in shaft…

A: GIVEN DATA - A GEAT TRAIN GIVEN  WE HAVE TO FIND SHEAR STRESS ON SHAFT CD

Q: The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate…

A:

Q: Q3: The shaft consists of three concentric tubes, each made from the same material and having inner…

A: Handwriting.jpg

Q: 10-7. The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is…

A: Given data: The outer diameter of the copper pipe is do=40 mm. The inner diameter of the copper…

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly…

A: Calculated absolute maximum shear stress developed in the pipe. And the calculated angle of twist of…

Q: a) the principal stress and planes and (b) the maximum in-plane shear stress, average stress and its…

A:

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C…

A: Since the magnitude of the direct shear stress compared to the twisting and bending stresses is very…

Q: Q1/ The copper pipe has an outer diameter of 3.0 in. and an inner diameter of 2.8 in. If it is…

A:

Q: The shaft has a radius of 15 mm with shear modulus of elasticity of 75 GPa. Determine the normal and…

A:

Q: The coupling is used to connect the tWo shafts together. Assuming that the shear stress in the bolts…

A:

Q: Q2:The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear stress in…

A: Given data: The diameter of the shaft, d = 50 mm. Calculate the torque at the shaft AB, TAB=900…

Q: The copper pipe has an outer diameter of 3 in. and an inner diameter of 2.50 in. If it is tightly…

A: Given data

Q: The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly…

A: Given, Outer diameter = 40 mm=0.04m Outer radius = 0.02m Inner Diameter = 37 mm=0.037m inner radius…

Q: The A-36 steel bar consists of two segments, one ofcircular cross section of radius r, and one of…

A: The strain energy stored in circular section,

Q: Q2:The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear stress in…

A:

Q: The solid aluminum shaft has a diameter of 50 mm and allowable shear stress of tallow = 60 MPa.…

A:

Q: The 200-mm-diameter aluminum cylinder supports a compressive load of 300 kN. Determine the average…

A:

Q: The plastic hexagonal tube is subjected to a torque of 150 N # m. Determine the mean dimension a of…

A: Given: The torque on a plastic hexagonal tube is T=150 N-m. The allowable shear stress on a plastic…

Q: If the applied shear force V = 18 kip, determine the maximum shear stress in the member.

A: Given data τallow=8 ksi

Q: Three forces of 500 lb, 800 lb, and 600 lb are applied to the end of the 2-in-diameter bar, as…

A:

Q: The copper pipe has an outer diameter of 3 in. and an inner diameter of 2.5 in. If it is tightly…

A: Given Data: The outer diameter of shaft is d0 = 3 in. The inner diameter of shaft is di = 2.5 in.…

Q: The 6-hp reducer motor can turn at 1200 rev>min. If the shaft has a diameter of 5 8 in.,…

A: Given: The power of the reducer motor is P=6 hp. The angular velocity of the reducer motor is ω=1200…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr %3D Tmax Ip

A: Given Circular shaft To find ζmaax=TrIP

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C…

A: Write the given data: Understand the effects of the 20 lb force on the member CD as shown in the…

Q: The rod has a diameter of 40 mm. If it is subjected to the force system shown, determine the stress…

A: Understand that the point A lies on the outer periphery of the shaft on the z axis. The Torsional…

Q: 2. The shaft is hollow from A to B and solid from B to C. (a) Determine the maximum shear stress…

A:

Q: The 2-m-long tube is made of an elastic perfectly plastic material as shown. Determine the applied…

A:

Q: The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is subjected to the…

A: Given data: Outer diameter of shaft = 100 mm                     The inner diameter of the shaft =…

Q: The gear motor can develop 14 hp when it turns at 600 rev>min. If the shaft has a diameter of 12…

A: Given Data: The power developed by the motor is P = 14 hp. The number of revolutions is N = 600…

Q: The lever is held to the fixed shaft using the pin AB. If the couple is applied to the lever,…

A: Given figure,  Take a point O in the centre on the line AB.

Q: 4-The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A:

Q: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is…

A: Given: The thickness of the wall is t=0.025 in. The inner diameter of the wall is d=0.5 in. The…

Q: The plastic tube is subjected to a torque of 150 N # m. Determine the average shear stress in the…

A: Torque=150 N-m =150×103 N-mm ; mean dimension (a) =200 mm ; thickness (t)=3 mm ;…

Q: The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is subjected to the…

A:

Q: The thin-walled pipe has an inner diameter of 1.2 cm and a thickness of 0.06 cm. If it is subjected…

A: Determine the axial and hoop tension as follows.

Q: The A-36 steel pipe is subjected to the axial loading of 60 kN. Determine the change in volume of…

A: Given data: Axial load subjected on the pipe, P = 60 kN. The inner diameter of the pipe, di = 30…

Q: The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is subjected to the…

A: Given: Outer diameter of shaft is 100 mm. Inner diameter of shaft is 80 mm.

Q: Q4. The steel shaft is L mm long and is screwed into the wall using a wrench. Determine the maximum…

A: Given data: The length of the steel rod is L = 380 mm. The magnitude of the couple forces F = 400…

Q: The hollow circular shaft is subjected to an internal torque of T = 1 0 kN # m. Determine the shear…

A: Given,Torque(T)=10 KN-m=107 N=mmBy torsion equation:→TJ=τRWhere,J=Polar moment of…

Q: The box beam is subjected to the 26-kN force that is applied at the center of its width, 75 mm from…

A: Given, P = 26 kN

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. The pipe is fixed at…

A:

Q: The bar has a circular cross section with 1-in diameter. If the torque TO = 1000 in-lb, determine…

A:

Q: If the box wrench is subjected to the 50-lb force, determine the principal stresses and maximum…

A: Draw the section a-a with shear force and bending moments.     Apply force equilibrium in the…

Q: Two spanners are used to tighten the pipe. If P =200 N is applied to each spanner, determine the…

A: Given:P=200 ND=25 mmd=20 mm

Q: 2. Given the shaft is loaded with torque and force acting at location B and C. Given the diameter of…

A: Given: The diameter of shaft, d = 1 in

Q: 15 kN-m 30 kN-m 75 kN-m 30 kN-m

A:

Q: The board is subjected to a tensile force of 200 lb. Determine the average normal and average shear…

A: The magnitude of the tensile force is, W=200 lb The orientation of the plane is, θ=20° The breadth…

Q: Determine the internal torque at each section and show the shear stress on differential volume…

A: The internal torque acting at section A-B can be written as below, TAB=300 N·m The internal torque…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.