6 solve 6 show complete STEP BY STEP solution, and draw a FBD. 5. Two bars are used to support a load. When unloaded, AB is 5 in. Iong, AC is 8 in.long, and the ring at A has coordinates (, 0). If a load P acts on the ring at A, thenormal strain in AB becomes cAB = 0.02 in/in., and the normal strain in ACbecomes CAC = 0.035 in/in. Determine the coordinate position of the ring due tothe load.60°5 in.8 in.6. Two bars are used to support a load P. When unloaded, AB is 5 in. long, AC is 8in. long, and the ring at A has coordinates (0, 0). If a load is applied to the ring atA, so that it moves it to the coordinate position (0.25 in., -0.73 in.), determine thenormal strain in each bar. (Use the figure in Prob.5)

Answered: Image /qna-images/answer/ec5745fd-9cce-45eb-937b-0066768240b3.jpg

B 60 5 in. 8 in. A P 6. Two bars are used to support a load P. When unloaded, AB is 5 in. long, AC is 8 in. Iong, and the ring at A has coordinates (0, 0). If a load is applied to the ring at A, so that it moves it to the coordinate position (0.25 in., -0.73 in.), determine the normal strain in each bar. (Use the figure in Prob.5)

B 60 5 in. 8 in. A P 6. Two bars are used to support a load P. When unloaded, AB is 5 in. long, AC is 8 in. Iong, and the ring at A has coordinates (0, 0). If a load is applied to the ring at A, so that it moves it to the coordinate position (0.25 in., -0.73 in.), determine the normal strain in each bar. (Use the figure in Prob.5)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.13P: An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 ×...

See similar textbooks

Similar questions

A 4.75-in, outside diameter polyethylene pipe designed to carry chemical waste is placed in a trench and bent around a quarter-circular 90° bend (see figure). The bent section of the pipe is 52 ft long. Determine the maximum compressive strain If the normal strain cannot exceed 6.1 × 10-3 , what is the maximum diameter of the pipe? If d = 4.75 in., what is the minimum acceptable length of the bent section of the pipe?
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
A rectangular block has dimensions of 3 in, 4 in, and 5 in along the X-, y-, and z- axes, respectively. The block is subjected to triaxial loading of three uniformly distributed loadings of 30 kips (C), 45 kips (T), and 60 kips (C) along the x-, y-, and z- axes, respectively. If the strain along the X- axis and the z-axis are 0.00021 (C) and 0.00042 (T), respectively, determine the Poisson's ratio and the modulus of elasticity of the material. Also, what is the change in volume of the material?
Two fully loaded tractor trailers travel over the bridge putting substantial loading on the structure. As they pass over the middle of the bridge, one of the vertical supporting pillars, which is fixed at its bottom, deforms as shown below. The weight of the trucks causes point T to move to point T'—a distance of 2.5 cm along the x-axis. If the pillar has an original height of 27 m , find the shear strain at point T.
A cantilever beam with a rectangular cross section (width b = 20 mm, height Ii = 175mm) is loaded by a force P that acts at the mid-height of the beam and is inclined at anangle a to the vertical (see figure). Two strain gages are placed at point C, which also isat the mid-height of the beam. Gage A measures the strain in the horizontal direction,and gage B measures the strain at an angle = 600 to the horizontal. The measuredstrainsaree A = 145 X 10_6 and 68 = —165 X lO_6.Determine the force P and the angle a, assuming the material is steel with £ = 200 GPaand v = 1/3.
Question # 1 Fig 2 shows an unstressed aluminum plate 2/4 inches thick. A circle of 9.5 inches diameter is scribed on it. Normal stresses of 15 ksi and 22 ksi, along x and y direction, are caused by forces acting in the plane of the plate. For Poisson's ratio 4 and modulus of elasticity 10 *10^6psi,then determine the following (a)change in the length of diameter AB (b)change in diameter CD (c)variation in the plate thickness (d)the volume change of the plate
The strain at point A on a beam has components Px = 450(10-6), Py = 825(10-6), gxy = 275(10-6), Pz = 0. Determine (a) the principal strains at A, (b) the maximum shear strain in the x–y plane, and (c) the absolute maximumshear strain.
1.A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are epsilon_{x} = 0.40 * 10 ^ - 3 and epsilon_{y} = 0.30 * 10 ^ - 3 determine and Use sigma_{y}; E = 110 GPa and y = 0.35 . sigma_{x}. Use E= 110 GPa and v=0.35. Show complete free body diagram.
In uniaxial loading the poisson's ratio is 0.30 and the strain in the x- direction is 250 x 10^-6 . What is the strain in the z- direction? a. -7.5 x 10^-5 b. 9.5 x 10^-5 c. -8.5 x 10^-5 d. 7.5 x 10^-5 Show the answer with complete solution
A sheet of steel is stretched biaxially in the xy-plane. The strains in the sheet are described below. Determine the stresses along the x and y axes. Use E=200 GPa and v=0.28 Ex = 0.4 x 10‐³ Ey = 0.3 x 10‐³