(b) A jet of water, having a velocity of 30 m/s impinges on a series of vanes with a velocity of 15 m/s. The jet makes an angle of 30" to the direction of motion of the vane when entering and leaves the vane at an angle of 120". (i) Sketch the velocity diagrams at the entrance and exit Determine the vane angles so that the water enters and leaves the vane without shock. If the jet is 60 mm in diameter. determine the work done for every second. What is the velocity the water as it exits the vane? (ii) (iii) (iv)

(b) A jet of water, having a velocity of 30 m/s impinges on a series of vanes with a velocity of 15 m/s. The jet makes an angle of 30" to the direction of motion of the vane when entering and leaves the vane at an angle of 120". (i) Sketch the velocity diagrams at the entrance and exit Determine the vane angles so that the water enters and leaves the vane without shock. If the jet is 60 mm in diameter. determine the work done for every second. What is the velocity the water as it exits the vane? (ii) (iii) (iv)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature.
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature. show and expalin each step please
I am studying for an exam this week, and I want to check my steps and answers for this one problem. Air enters a nozzle steadily with a density of 2.21 kg/m^3 and velocity of 40 m/s and leaves at 180 m/s with a density of 0.762 kg/m3. If the nozzle inlet has an area of 90 cm^2, determine: a) The Volumetric flow rate at the in let (m^3/s) b) The Mass flow rate (kg/s) through the nozzle; c) The exit area of the nozzle (cm^2)
a=2 , b=1 The properties of the air in the inlet section with A1 = 0.25ab m2 in a converging-diverging channel are given as U1 = 25a,b m/s, T1 = 3ab K, P1 = 13a,b kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
The maximum velocity of an air flow (v= 700 ms-1 and T=160 oC
Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 m2, ρ1=1300 kgm/m3. At exit: A2=10 m2, ʋ2=0.00125 m3/kg, ῡ2=3 m/min. Determine the following: a) ḿ1 in kg/min b) ῡ1 in m/min
14A fluid flows at a speed of 7.5 m/s in a pipe with a diameter of 35 cm. What is the power, in W, of the pump to overcome the irreversible pressure drop when the pressure drop along the pipe is calculated to be 6300 Pa?
3. In a refinery, certain oil with sp.gr 0.9 flows with a velocity of 2 m/s in a pipe of diameter 30cm. Along the flow, the pipe diameter gets reduced to 25 cm. Determine the velocity and mass flow rate of oil at this section. 4. A circular pipe of uniform diameter 500mm carries water under pressure 30 N/cm2 . The mean velocity of water at the inlet (at the datum) is 2.0 m/s. Find the total head or total energy per unit weight of the water at a cross-section, which is 5 m above the datum line. 5. A tapered pipe, through which water is flowing, is having diameter, 30cm and 20 cm at the cross-sections 1 and 2 respectively. The velocity of water at section 1 is given as 3.5m/s. Find the velocity head at section 1 and 2 and also rate of discharge. 6. Water is flowing through a pipe having diameter 300mm and 200 mm at the bottom and upper end respectively. The pressure at the lower(bigger) end is 25 N/cm2 and the pressure at the upper end is 10 N/cm2. Determine the difference in datum…
Provide the solution and diagram. Air enters the tower at the rate of 60 kg/s. The entrance enthalpy is 86 KJ/kg and exit enthalpy of 53 KJ/kg. Find the temperature range of the tower if mass flow rate of water is 30 kg/s. A. 14.34 oC B. 16.34 oC C. 10.23 oC D. 15.76oC
Consider the flow system illustrated below operating at steady state Obtain the maximum value of the velocity in the pipe 3, ?3??? (in cm/s).
Water flows from a tap at a pressure of 250 kPa above atmospheric prrssure. What is the velocity of the jet if frictional effects are neglected?A. 12.2 m/sB. 16.5 m/sC. 22.4 m/sD. 27.4 m/s
Air flows into a turbine at a rate 30 [m 3 /s], a temperature of 1100 [K] anda pressure of 300 [kPa]. The turbine’s work output is 200 [kJ/kg]. Determine thetemperature of the air at the exit, the power output in [kW] and the isentropicefficiency. The pressure ratio of the turbine is 3. The specific gas constant, R, for airis 0.287 [kJ/kg-K].